protech PA-6225 User manual

USER
MANUAL
PA-6225
15” Waterproof True Flat
Touch POS Terminal
Powered by Intel®Celeron®
J1900 Quad-Core
PA-6225 M6

PA-6225 POS System
COPYRIGHT NOTICE & TRADEMARK
All trademarks and registered trademarks mentioned herein are the property of their
respective owners.
This manual is copyrighted in August 2017. You may not reproduce or transmit in
any form or by any means, electronic, or mechanical, including photocopying and
recording.
DISCLAIMER
This operation manual is meant to assist both Embedded Computer manufacturers
and end users in installing and setting up the system. The information contained in
this document is subject to change without any notice.
CE NOTICE
This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.

Page: 2
FCC NOTICE
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
You are cautioned that any change or modifications to the equipment not
expressly approve by the party responsible for compliance could void your
authority to operate such equipment.
CAUTION: Danger of explosion may occur when the
battery is incorrectly replaced. Replace the battery only
with the same or equivalent type recommended by the
manufacturer. Dispose of used batteries according to
the manufacturer’s instructions.

Contents
Page: i
TABLE OF CONTENTS
CHAPTER 1 INTRODUCTION
1-1 About This Manual ........................................................................... 2
1-2 POS System Specification................................................................. 3
1-3 System Specifications ....................................................................... 8
1-4 Safety Precautions........................................................................... 16
CHAPTER 2 SYSTEM CONFIGURATION
2-1 System External I/O Port & Pin Assignment................................... 18
2-2 Power Button, Ports, Connectors and Jumpers ............................... 19
2-2-1 Power Button .................................................................... 19
2-2-2 DC-IN Port........................................................................ 19
2-2-3 VGA Port.......................................................................... 19
2-2-4 COM Ports........................................................................ 20
2-2-5 LAN Port........................................................................... 20
2-2-6 Cash Drawer Port (Optional) ............................................ 21
2-2-7 2nd Display Power Port (Optional)................................... 21
2-2-8 RAID Power Port (Optional) ............................................ 21
2-2-9 USB Ports ......................................................................... 22
2-2-10 Printer Power Port (Optional)......................................... 22
2-2-11 UPS Power Port (Optional)............................................. 22
2-3 Mainboard Component Locations & Jumper Settings..................... 23
2-4 How to Set Jumpers ........................................................................ 24
2-4-1 COM Port RI & Voltage Selection ................................... 26
2-4-2 COM Connectors .............................................................. 27
2-4-3 i-Button Connector............................................................ 27
2-4-4 i-Button Function Selection .............................................. 27
2-4-5 Cash Drawer Control Selection......................................... 28
2-4-6 Cash Drawer Power Selection........................................... 32
2-4-7 USB Connectors................................................................ 33
2-4-8 LED Connectors................................................................ 33
2-4-9 Power for Thermal Printer Connector............................... 33
2-4-10 Power Connectors............................................................. 34
2-4-11 External Speaker Connectors............................................ 34

Contents
Page: ii
2-4-12 Inverter Connectors........................................................... 34
2-4-13 Power Button Connectors ................................................. 35
2-4-14 LED Backlight Power Control Selection .......................... 35
2-4-15 LED Backlight Power Connector...................................... 36
2-4-16 Panel Resolution Selection................................................ 36
2-4-17 LVDS Connector............................................................... 37
2-4-18 Touch Panel Connectors ................................................... 37
2-4-19 Touch Panel Signal Interface Selection............................. 38
2-4-20 Clear CMOS Data Selection ............................................. 38
2-4-21 MSR/Card Reader Connectors.......................................... 39
2-4-22 SATA & SATA Power Connectors................................... 39
2-4-23 Printer Connector.............................................................. 40
2-4-24 Mini-PCIe / mSATA Connector........................................ 41
2-5 Printer Board Component Locations & Pin Assignment................. 42
2-5-1 Printer Board: PDAC-3100............................................... 42
2-5-1-1 Power Supply Connector .................................... 43
2-5-1-2 RS-232 Interface Connector................................ 43
2-5-1-3 Auto-Cutter Connector........................................ 44
2-5-1-4 USB Connector................................................... 44
2-5-1-5 Thermal Head/Motor/Sensor Connector............. 45
2-5-1-6 Terminal Assignment Connector......................... 47
2-5-2 Printer Board: MB-1030................................................... 48
2-5-2-1 Power Supply Connector .................................... 49
2-5-2-2 RS-232 Interface Connector................................ 49
2-5-2-3 Thermal Head/Motor/Sensor Connector............. 50
2-5-2-4 Auto-Cutter Connector........................................ 52
2-5-2-5 Paper-Near-END Sensor Connector ................... 52
2-5-2-6 USB Interface Connector.................................... 53
2-5-2-7 Terminal Assignment Connector......................... 53
2-5-3 Printer Board: MB-1011 & MB-1013............................... 54
2-5-3-1 Power Supply Connector .................................... 55
2-5-3-2 RS-232 Interface Connector................................ 55
2-5-3-3 Thermal Head/Motor/Sensor Connector............. 56
2-5-3-4 Auto-Cutter Connector........................................ 58
2-5-3-5 USB Interface Connector.................................... 58

Contents
Page: iii
2-5-3-6 Terminal Assignment Connector......................... 59
2-6 VFD Board Component Locations & Pin Assignment.................... 60
2-6-1 VFD Board: MB-4103, LD720......................................... 60
2-6-1-1 Power Switch Selection....................................... 61
2-6-1-2 RS-232 Serial Interface Connector ..................... 61
2-7 MSR Board Component Locations & Pin Assignment ................... 62
2-7-1 ID-TECH .......................................................................... 62
2-7-1-1 Main Connector .................................................. 62
2-7-2 SYSKING......................................................................... 63
2-7-2-1 Main Connector .................................................. 63
2-7-3 MB-3012............................................................................ 64
2-7-3-1 Information Button Reader ................................. 64
2-7-3-2 Output Connector................................................ 64
CHAPTER 3 SOFTWARE UTILITIES
3-1 Driver.............................................................................................. 66
3-1-1 Introduction....................................................................... 66
3-1-2 Intel® Chipset Software Installation Utility...................... 67
3-1-3 VGA Driver Utility........................................................... 68
3-1-4 LAN Driver Utility............................................................ 68
3-1-5 Sound Driver Utility.......................................................... 69
3-1-6 Touchscreen Driver Utility ............................................... 69
3-1-7 Fingerprint Driver Utility.................................................. 70
3-1-8 RFID Module Driver Utility (Optional)............................ 70
3-1-9 Wireless Module Driver Utility (Optional)....................... 71
3-1-10 For Intel Trusted Execution Engine Interface (TXE)........ 71
3-2 Peripheral Devices .......................................................................... 72
3-2-1 Printer Board: MB-1030................................................... 72
3-2-2 VFD: MB-4103 (RS-232)............................................. 127
3-2-3 MSR: MB-301x (USB)................................................. 133
3-2-4 MSR: GIGA-TMS MJR243 (RS-232).......................... 141
3-3 API................................................................................................ 144
3-3-1 API Package Content ...................................................... 144
3-3-2 API Procedure................................................................. 145
3-3-3 Sample Code................................................................... 147

Contents
Page: iv
3-3-4 Cash Drawer.................................................................... 150
3-3-5 API Function................................................................... 151
3-3-6 Cash Drawer Function..................................................... 152
3-4 BIOS Operation ............................................................................ 153
3-4-1 Introduction..................................................................... 153
3-4-2 Accessing Setup Utility................................................... 155
3-4-3 Main…............................................................................ 158
3-4-4 Advanced ........................................................................ 160
3-4-5 Chipset............................................................................ 185
3-4-6 Security........................................................................... 192
3-4-7 Boot................................................................................. 193
3-4-8 Save & Exit..................................................................... 196
3-5 Watchdog Timer Configuration .................................................... 198
3-6 BIOS Update Instructions............................................................. 201
3-7 System Resource Map................................................................... 205
CHAPTER 4 SYSTEM DIAGRAMS
Exploded Diagrams for Panel PC................................................................ 221
Exploded Diagrams for Stand ..................................................................... 234
Exploded Diagrams for Peripheral Devices ................................................ 266
Exploded Diagrams for Packing.................................................................. 272

PA-6225 SERIES USER MANUAL
Page 1
INTRODUCTION
This chapter gives you the information for the PA-6225. It also outlines
the system specifications.
The following topics are included:
About This Manual
POS System Illustration
System Specifications
Safety precautions
Experienced users can jump to Chapter 2 starting page
17 for a quick start.
CHAPTER
1

Chapter 1 Introduction
PA-6225 SERIES USER MANUAL
Page 2
1-1. ABOUT THIS MANUAL
Thank you for purchasing our PA-6225 Series System. The PA-6225 is an updated
system designed to be comparable with the highest performance of IBM AT personal
computers. The PA-6225 provides faster processing speed, greater expandability and
can handle more tasks than before. This manual is designed to assist you how to install
and set up the whole system. It contains four chapters. Users can configure the system
according to their own needs.
Chapter 1 Introduction
This chapter introduces you to the background of this manual. It also includes
illustrations and specifications for the whole system. The final section of this chapter
indicates some safety reminders on how to take care of your system.
Chapter 2 System Configuration
This chapter outlines the location of motherboard, printer, VFD, MSR components
and their function. You will learn how to set the jumpers and configure the system to
meet your own needs.
Chapter 3 Software
This chapter contains detailed information for driver installations of the Intel®Utility,
VG, LAN, Sound, Touch Screen, embedded peripheral devices, BIOS setup & update,
Watchdog timer and resource map.
Chapter 4 System Diagrams
This chapter includes the exploded diagrams and part numbers of PA-6225
components.

Chapter 1 Introduction
PA-6225 SERIES USER MANUAL
Page 3
1-2. POS SYSTEM ILLUSTRATION
15” LCD &
Touchscreen
Stand
(Optional)
Vertical Module:
MSR & i-Button
HDD & its cover
Cable
Cover
LED
Indicator
Rotatable part
for Panel PC
Front View
Rear View
380
240
385

Chapter 1 Introduction
PA-6225 SERIES USER MANUAL
Page 4
Top View
Side View
270
310
45°
225
Unit: mm
With printer
Front View
Side View
239.74
182.27
111
57.47
50°
134.26
111
15.15

Chapter 1 Introduction
PA-6225 SERIES USER MANUAL
Page 5
Printer Opened
50°
Ø 80
86.5
75
Unit: mm

Chapter 1 Introduction
PA-6225 SERIES USER MANUAL
Page 6
Caution: Please refer to the pictures below to close the printer door
properly.

Chapter 1 Introduction
PA-6225 SERIES USER MANUAL
Page 7
Small stand type
Front View
Rear View
380
408
303
220
3.2
Side View
Quarter View
310
45°
215
252
58
Unit: mm

Chapter 1 Introduction
PA-6225 SERIES USER MANUAL
Page 8
1-3. SYSTEM SPECIFICATIONS
System
CPU
Intel®Celeron®J1900 Quad-Core 2.0GHz
Memory
1 x DDR3 SO-DIMM 204-pin socket, up to 8GB
OS Support
Windows POSReady7
Windows Embedded 8 Industry Pro Retail
Windows 10 IoT Enterprise LTSB 2016
LAN
1 x Giga LAN
VGA
1 x DB-15
Wireless LAN (Optional)
802.11 b/g/n
AP distance
0˚
90˚
180˚
270˚
5M
-32 dB
-27 dB
-37 dB
-33 dB
10M
-43 dB
-37 dB
-46 dB
-44 dB
Note:
1. Test tolerance: ±5dB
2. AP: ASUS RT-N56U (2 x internal antenna with 3.8 dBi
gain)
Angle: 0°
AP
(Distance)
Angle: 180°Angle: 90° Angle: 270°
AP
Audio
2W speaker & Line-out Port
BIOS
AMI SPI BIOS, 8 Mbits with VGA BIOS
RTC Accuracy
3 days ± 3 seconds
System Weight
With power adapter approx. 7 kg
Dimension (W x H x D)
377mm x 318mm x 240mm
Viewing Angel
24~30˚

Chapter 1 Introduction
PA-6225 SERIES USER MANUAL
Page 9
120W
Power Supply: 72 ~ 120Watt power adapter
Power Consumption (AC):
System
Status
CPU/
HDD/
Memory
VFD
Printer
COM & USB
Ports to supply
power of Rear I/O
Consumption
OFF
Off
without
2W
IDLE
Turns on, but
not to execute
extra AP
Runs
new
ticker
Standby
19.8W
Working
(without
printer)
100% loading
of burn-in test
25.6W
Working
(with
printer)
DC24V
1.4A dummy
load
59.1W
Full Loading
USB dummy load
500mA x4
68.9W
Certificate: CE, CE-LVD, FCC
Type
Standard
Description
EMI
EN 55022 Class A
-
EMS
EN 55024
-
IEC 61000-4-2
ESD
8kV air discharge
4kV contact discharge
IEC 61000-4-3
RS
80~1000MHz, 3V/m, 80% AM(1kHz)
IEC 61000-4-4
EFT
AC Power Port: 1kV
DC Power Port: 0.5kV
Signal Ports & Telecommunication
Ports: 0.5kV
IEC 61000-4-5
Surge
AC Power Port:
Line to line: 1kV
Line to earth(GND): 2kV
DC Power Port:
Line to earth(GND): 0.5kV
Signal and Telecommunication Port:
Line to GND: 1kV
IEC 61000-4-6
CS
0.15~80MHz, 3Vrms, 80% AM, 1kHz
IEC 61000-4-8
PFMF
50Hz, 1A/m
IEC 61000-4-11
Voltage Dips
> 95% reduction for 0.5 periods
30% reduction for 25 periods
Voltage Interruptions
> 95% reduction for 250 periods

Chapter 1 Introduction
PA-6225 SERIES USER MANUAL
Page 10
Display
15” TFT XGA LCD
Max. Resolution: 1024 x 768
Signal Interface: TTL (24-bit)
Touchscreen
15” true flat screen
5-wire resistive type
Projected capacitive type
Brightness
Resistive Touchscreen:
Minimum
Typical
Maximum
160 cd/m2
200 cd/m2
-
Projected Capacitive Touchscreen:
Minimum
Typical
Maximum
180 cd/m2
225 cd/m2
-
Environment
Temperature
Operating: 0~35°C (32 ~ 95°F)
Storage: -20~60°C (-4 ~ 140°F)
Humidity
20~90%
Optional accessories
MSR & i-Button
ISO I ,II, III; JIS I,II and support information key reader
Fingerprint
8-bit grayscale reader
2nd Display
8” LCD (Resolution: 800 x 600)
10.4” LCD (Resolution: 1024 x 768 or 800 x 600)
Customer Display
Interface: RS-232C Baud Rate: 9600/19200 bps
Placement: 20 columns and 2 lines, each column is 5
x 7 dots
Brightness: cd/m2
Dimensions:
18.2
107.2

Chapter 1 Introduction
PA-6225 SERIES USER MANUAL
Page 11
0.55 0.75
6.75
3.75
0.8
1.0
Standard Code
CP-437, CP-850, CP-857, CP-865, Katakana
International Characters
USA, FRANCE, GERMANY, UK, DENMARK I,
SWDEN, ITALY, SPAIN, JAPAN, NORWAY,
DENMARK II, RUSSIA, SLAVONIC
Printer
2” or 3” easy loading thermal printer with auto-cutter
Printer:
Items
Specifications
Printing method
Thermal dot line printing
Printing accuracy
1mm /5M
Paper feed pitch
0.0625 mm
Maximum Paper-Roll
thickness
80mm
Total dots per line &
Printable dots per line
2inch 432 dots;
3inch 576 dots
Maximum print speed
2inch 200 mm/s;
3inch 170 mm/s
Print width
2inch 54 mm;
3inch 72mm
Paper width
2inch 58 +0/-1 mm;
3inch 80 +0/-1 mm

Chapter 1 Introduction
PA-6225 SERIES USER MANUAL
Page 12
Printer
A mm (Printing Width)
2 inch (A:54, C:58, D:2)
3 inch (A:72, C:80, D:4)
D mm
D mm
0
-1 mm (Paper Width)
C
Auto-cutter:
Items
Specifications
Paper cutting method
Slide cutting
Type of paper cutting
Full cut and Partial cut (1.5 ±
0.5 mm tab left at the center)
Paper curling tendency
Fixed blade side and Movable
blade side
Minimum paper core
diameter
φ8 mm (paper thickness: 75μm
or thin)
φ18 (paper thickness: thicker
than 75μm)
Minimum paper cutting
length
10 mm
Cutting processing time
Approx. 0.5 s/cycle
Cutting frequency
1 cut/2 s max.
Standard Code
CP-437, CP-850, CP-857, CP-737, CP-852, CP-860,
CP-862, CP-863, CP-865, CP-866, CP-1250,
CP-1251, CP-1252, CP-1253, CP-1254, CP-1257,
Katakana
KANJI
JAPANESE (SHIFT-JIS) Code,
TRADITIONAL CHINESE Code
International Characters
USA, FRANCE, GERMANY, UK, DENMARK I,
SWDEN, ITALY, SPAIN I, JAPAN, NORWAY,
DENMARK II, SPAIN II, LATIN AMERICA,
KOREA, RUSSIA, SLAVONIC

Chapter 1 Introduction
PA-6225 SERIES USER MANUAL
Page 13
RAID:RAID 1