protech prox PA-J510 User manual

USER
MANUAL
PA-J510
15" High Performance
POS Terminal
PA-J510M3

PA-J51015” High
Performance POS Terminal
COPYRIGHT NOTICE & TRADEMARK
All trademarks and registered trademarks mentioned herein are the
property of their respective owners.
This manual is copyrighted in June 2023. You may not reproduce
or transmit in any form or by any means, electronic, or
mechanical, including photocopying and recording.
DISCLAIMER
This user’smanual is meant to assist users in installing and setting up
the system. The information contained in this document is subject to
change without any notice.
CE NOTICE
This is a class A product. In a domestic environment this product may
cause radio interference in which case the user may be required totake
adequate measures.

FCC NOTICE
This equipment has been tested and found to comply with the limits for
a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
You are cautioned that any change or modifications to the equipment
not expressly approve by the party responsible for compliance could
void your authority to operate such equipment.
CAUTION: Danger of explosion may occur when the battery
is incorrectly replaced. Replace the battery
only with the
same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer’s
instructions.
WARNING: Some internal parts of the system may have
high electrical voltage. We strongly recommend that only
qualified engineers are allowed to service and disassemble
the system. If any damages should occur on the system and
are caused by unauthorized servicing, it will not be covered
by the product warranty.

i
Contents
Revision History ............................................................................................. v
1Introduction ......................................................................................... 1-1
1.1 About This Manual ..................................................................... 1-2
2Getting Started .................................................................................... 2-1
2.1 Package List............................................................................... 2-2
2.2 System Overview ....................................................................... 2-3
2.2.1 Panel PC............................................................................. 2-3
2.2.2 Normal Stand Only.............................................................. 2-4
2.2.3 Normal Stand with 10.1" 2nd Display ................................. 2-5
2.3 System Specifications ................................................................ 2-6
2.4 Safety Precautions ..................................................................... 2-8
3System Configuration......................................................................... 3-1
3.1 System External I/O Ports Diagram ........................................... 3-2
3.2 Mainboard Component Locations & Jumper Setting ................. 3-3
3.3 How to Set Jumpers................................................................... 3-4
3.4 Main Board Connector & Jumper Quick Reference Table ......... 3-6
3.5 Setting Main Board Connectors and Jumpers ........................... 3-7
3.5.1 Power Switch ...................................................................... 3-7
3.5.2 DC IN Connector (DC In).................................................... 3-7
3.5.3 1st Display Port (MDP1) ..................................................... 3-8
3.5.4 COM Ports (COM1, COM2) ................................................ 3-9
3.5.5 LAN Port (LAN1) ............................................................... 3-10
3.5.6 USB Type C Port (USB Type C) ....................................... 3-11
3.5.7 Dual USB 2.0 Ports (USB2)..............................................3-12

ii
3.5.8 Dual USB 3.0 Ports (USB1)..............................................3-12
3.5.9 2nd Display Port (MDP2) .................................................. 3-13
3.5.10 HDMI Port Connector (HDMI1).........................................3-14
3.5.11 Cash Drawer Port (DRW) ................................................. 3-15
3.5.12 Internal USB Wafer (JUSB1, JUSB9) ............................... 3-18
3.5.13 Internal USB Wafer (JUSB7) ............................................ 3-19
3.5.14 M.2 M-Key Connector for SSD (M2_M1).......................... 3-20
3.5.15 M.2 M-Key Connector for SSD (M2_M2).......................... 3-22
3.5.16 M.2 E-Key Connector for Wi-Fi (M2_E1)..........................3-24
3.5.17 Speaker Wafer (JSPK1).................................................... 3-26
3.5.18 Microphone Connector (JMIC1)........................................ 3-26
3.5.19 Power Output 24V Wafer (J24V_OUT1)........................... 3-26
3.5.20 System LED Wafer (JSYS_LED1) ....................................3-27
3.5.21 CPU Fan Wafer (CPU_FAN1)........................................... 3-27
3.5.22 Power Button Wafer (JPWRBTN1) ...................................3-28
3.5.23 Battery Wafer (JBAT1) ...................................................... 3-28
3.5.24 System Reset Wafer (JRST1)........................................... 3-28
3.5.25 USB Signal Selection (JP1) ..............................................3-29
3.5.26 USB Signal Selection (JP2) .............................................. 3-29
3.5.27 Cash Drawer Voltage Selection (JP3) .............................. 3-30
3.5.28 Clear CMOS Data Selection (JPCMOS1) ........................ 3-31
3.6 A/D Board Component Locations & Jumper Setting................ 3-32
3.7 A/D Board Connector & Jumper Quick Reference Table ......... 3-33
3.8 Setting A/D Board Connectors and Jumpers ........................... 3-34
3.8.1 1st Display Port Connector (MDP1)..................................3-34
3.8.2 Embedded DisplayPort Connector (JEDP2)..................... 3-35
3.8.3 Speaker Connector (JSPK1) ............................................3-36
3.8.4 Inverter Connector (JINV1) ............................................... 3-36
3.8.5 LVDS Connector (LVDS1).................................................3-37

iii
3.8.6 USB 2.0 Connector (JUSB1, JUSB2, JUSB3).................. 3-38
3.8.7 Backlight Voltage Selection (JP_INV1)............................. 3-39
3.8.8 LVDS Panel Voltage Control Selection (JP_VDD1).......... 3-39
3.8.9 LVDS Backlight Control (JP1) ........................................... 3-40
4Software Utilities................................................................................. 4-1
4.1 Introduction................................................................................. 4-2
4.1.1 Installing Intel®Chipset Software Installation Utility ........... 4-3
4.1.2 Installing Graphics Driver Utility.......................................... 4-4
4.1.3 Intel®Management Engine Components Installer Installation.
........................................................................................... 4-5
4.1.4 Installing LAN Driver Utility ................................................. 4-6
4.1.5 Installing Intel®Serial I/O Driver Utility................................ 4-7
4.1.6 Installing Sound Driver Utility.............................................. 4-8
5BIOS SETUP ........................................................................................ 5-1
5.1 Introduction................................................................................. 5-2
5.1.1.1 Accessing Setup Utility ................................................... 5-4
5.1.2 Main .................................................................................... 5-7
5.1.3 Advanced ............................................................................ 5-8
5.1.3.1 Advanced - CPU Configuration.....................................5-10
5.1.3.2 Advanced - PCH-FW Configuration.............................. 5-11
5.1.3.3 Advanced - Trusted Computing .................................... 5-13
5.1.3.4 Advanced - ACPI Settings ............................................ 5-15
5.1.3.5 Advanced - F81967 Super IO Configuration ................5-16
5.1.3.6 Advanced - Hardware Monitor ...................................... 5-19
5.1.3.7 Advanced - F81967 Watchdog ..................................... 5-22
5.1.3.8 Advanced - USB Configuration.....................................5-23
5.1.3.9 Advanced - NVMe Configuration .................................. 5-24
5.1.4 Chipset .............................................................................. 5-25
5.1.4.1 System Agent (SA) Configuration ................................. 5-26

iv
5.1.4.2 PCH IO Configuration ................................................... 5-28
5.1.5 Security ............................................................................. 5-31
5.1.6 Boot................................................................................... 5-33
5.1.7 Save & Exit ....................................................................... 5-35
Appendix A System Diagrams....................................................A-1
PPC Memory Maintenance.......................................................................A-2
PPC M.2 2280 Maintenance.....................................................................A-4
PA-J510Memory Maintenance ................................................................A-5
PA-J510M.2 2280 Maintenance ..............................................................A-7
How To Turn System Touchscreen ...........................................................A-8
2nd Display Assembly ..............................................................................A-9
VFD Module Assembly ...........................................................................A-12
iButton Module Assembly .......................................................................A-14
Fingerprint Module Assembly .................................................................A-15
Barcode Scanner Assembly ...................................................................A-16
MSR Module Assembly ..........................................................................A-17
POS Type Assembly Exploded Diagram ................................................A-18
PPC Type Assembly Exploded Diagram ................................................A-19
Appendix B Technical Summary ................................................B-1
Block Diagram ..........................................................................................B-2
Interrupt Map ............................................................................................B-3
I/O MAP ..................................................................................................B-18
Memory Map...........................................................................................B-20
Configuring WatchDog Timer .................................................................B-23
Flash BIOS Update.................................................................................B-25

v
Revision History
v
The revision history of PA-J510 User Manual is described below:
Version No. Revision History Date
M3 Added: The default voltage of Cash Drawer
is “default at +24V”. (Page 2-6) 2023/6/15
M2 The description of Section 3.5.11 Cash Drawer
Port (DRW) has been revised. (Page 3-15) 2023/4/25
M1 Initial Release 2023/4/10

Page: 1-1
PA-J510SERIES USER MANUAL
1Introduction
This chapter provides the introduction for PA-J510 system
as well as the framework ofthe user manual.
The following topic is included:
•About This Manual

Chapter 1 Introduction
PA -J510SERIES USER MANUAL Page: 1-2
1.1 About This Manual
1.1 About This Manual
Thank you for purchasing our PA-J510 system. The PA-J510 is an updated system
designed to be comparable with the highest performance of IB M AT personal
computers. The PA-J510 provides faster processing speed, greater expandability and
can handle more tasks than before. This manual is designed to assist you how to
install and set up the whole system. It contains 5 chapters and 2 appendixes. Users can
configure the system according to their own needs. This user manual is intended for
service personnel with strong hardware background. It is not intended for general
users.
The following section describes the structure of this user manual.
Chapter 1 Introduction
This chapter introduces the framework of this user manual.
Chapter 2 Getting Started
This chapter describes the package contents and system specifications, and illustrates
the physical appearances for PA-J510 system. Read the safety reminders carefully on
how to take care of your system properly.
Chapter 3 System Configuration
This chapter describes the locations and functions of the system m ain board
components. You will learn how to prope rly configure the connectors and system
configuration jumpers on the main board and configure the system to meet your own
needs.
Chapter 4 Software Utilities
This chapter introduces how to install Intel Chipset Software Installation Utility,
Graphics Driver Utility, Intel Management Engine Components Installer Driver
Utility, LAN Driver Utility, Serial IO Driver Utility and Sound Driver Utility.
Chapter 5 BIOS Setup
This chapter provides BIOS setup information.
Appendix A System Diagrams
This appendix provides the exploded diagrams and part numbers of PA-J510.
Appendix B Technical Summary
This appendix provides the information about the system block diagram, allocation
maps for system resources, Watchdog Timer Configuration and Flash BIOS Update.

PA -J510Series User Manual
Page: 2-1
2Getting Started
This chapter provides the introduction for the PA-J510
system as well as the framework of the user manual.
The following topic is included:
•About This Manual
•POS System Illustration
•System Specifications
•Safety precautions
Experienced users can jump to Chapter 3 on page 3-1
for a quick start.

Chapter 2 Getting Started
PA -J510Series User Manual
Page: 2-2
2.1 Package List
If you discover any of the items listed below are damaged or lost, please contact
your local distributor immediately.
Item
Q’ty
PA-J510 POS System
1
Manual / Driver DVD
1
Power Adapter
1
Power Cord
1

Chapter 2 Getting Started
PA -J510Series User Manual
Page: 2-3
2.2 System Overview
Unit: mm
2.2.1 Panel PC
Front View Rear View
Side View
342
270
VESA 75
136
VESA 75
60.4
24.4

Chapter 2 Getting Started
PA -J510Series User Manual
Page: 2-4
2.2.2 Normal Stand Only
Unit: mm
Front View Rear View
Side View
342
270
322.4
DC In LAN
1st Dis. HDMI
Type C
COM2 COM1 DRW2nd Dis.
24.4

Chapter 2 Getting Started
PA -J510Series User Manual
Page: 2-5
2.2.3 Normal Stand with 10.1" 2nd Display
Unit: mm
Front View Rear View
Side View
342
270
322.4
DC In LAN
1st Dis. HDMI
Type C
COM2 COM1 DRW2nd Dis.
24.4
20.2
198.8

Chapter 2 Getting Started
PA -J510Series User Manual
Page: 2-6
2.3 System Specifications
2.3 System Specifications
System
CPU Support Intel
®
Core
®
i5-1145G7E / i3-1115G4E /
Celeron® 6305E / Pentium® 7505 CPU
Memory 1 x DDR4 SO-DIMM slot (up to 16GB)
Network 1 x Gigabit 10/100/1000 Base-T Fast Ethernet
1 x M.2 (E Key, 2230)
Power Supply 1 x 60/90 watt power adapter
Audio 1 x 2W speaker
System Weight
PPC: 3.9 kg
POS: 4.3 kg
POS + 2nd Display: approx. 5.3 kg (w/o power
adapter)
Dimensions
(W x H x D)
PPC: 342 x 270 x 60mm
POS: 342 x 270 x 195 mm (45 degree)
POS + 2nd Display: 342 x 291 x 237 mm
(45 degree)
O.S. Support Windows
®
11 / Windows
®
10 IoT Enterprise
Wall Mount Type  VESA 75 x 75mm standard
Storage
SATA 1 x M.2 2280, SATA interface
I/O Ports
Display
1 x Mini DP for Primary display (for Protech original
display only)
1 x Mini DP for 2nd display (for Protech original
display only)
1 x HDMI 1.4
USB Rear I/O: 2 x USB 2.0/ 2 x USB 3.1/ 1 x USB Type-C
Side I/O: 1 x USB 2.0
Serial Port 1 x RJ45 (support +5V/12V selectable)
LAN 1 x Giga LAN
Cash Drawer 1 x RJ11 (+12V or +24V selectable) (Default at +24V)
DC In 1 x 4-pin DC power jack
Option 1 x USB 2.0 or 1 x 24V Power USB (1A) or
1 x DC Out (1A)

Chapter 2 Getting Started
PA -J510Series User Manual
Page: 2-7
Add-Ons
Customer Display  20 columns x2 lines STN LCD display
MSR & i-Button ISO I,II,III;JIS II and support information key
(USB interface)
Fingerprint Silicon Fingerprint Module (USB interface)
Barcode Scanner
1D: EAN-13, EAN-8, UPC-A, UPC-E, ISSN, ISBN,
Codabar, Code 128, Code 93, ITF-6, ITF-14,
Interleaved 2 of 5, Industrial 2 of 5, Standard 2 of
5, Matrix 2 of 5, GS1 Databar, Code 39, Code 11
2D: PDF417, QR Code, Micro QR, Data Matrix,
Chinese sensible code
Display
LCD 15” IPS LCD (Resolution: 1024 x 768)
Brightness: 400 cd/m²
Touchscreen Bezel-free projected capacitive
Tilt Angle 0~50 degree
Environment
EMC & Safety CE / FCC
Operating Temp. 0°C ~ 35°C (32°F ~ 95°F)
Storage Temp. -20°C ~ 60°C (-4°F ~ 140°F)
Humidity 20% ~ 90%

Chapter 2 Getting Started
PA -J510Series User Manual
Page: 2-8
2.4 Safety Precautions
Before operating this system, read the following information carefully to protect your
systems from damages, and extend the life cycle of the system.
1. Check the Line Voltage
•The operating voltage for the power supply should be within the range of 100V
to 240V AC; otherwise, the system may be damaged.
2. Environmental Conditions
•Place your PA-J510on a sturdy, level surface. Be sure to allow enough space
around the system to have easy access needs.
•Avoid installing your PA-J510system in extremely hot or cold places.
•Avoid direct sunlight exposure for a long period of time (for example, in a
closed car in summer time. Also avoid the system from any heating device.). Or
do not use PA-J510when it has been left outdoors in a cold winter day.
•Bear in mind that the operating ambient temperature is between 0°C and 35°C
(32°F and 95°F).
•Avoid moving the system rapidly from a hot place to a cold place, and vice
versa, because condensation may occur inside the system.
•Protect your PA-J510from strong vibrations which may cause hard disk failure.
•Do not place the system too close to any radio-active device. Radio-active
device may cause signal interference.
•Always shut down the operating system before turning off the power.
3. Handling
•Avoid placing heavy objects on the top of the system.
•Do not turn the system upside down. This may cause the hard drive to
malfunction.
•Do not allow any objects to fall into this device.
•If water or other liquid spills into the device, unplug the power cord
immediately.

PA -J510Series User Manual
Page: 3-1
3 System Configuration
This chapter provides the information for the PA-J510 system.
It describes the jumper and connector settings, component
locations, and pin assignment.
The following topics are included:
•System External I/O Port Diagram
•Mainboard Component Locations & Jumper Setting
•How to Set Jumpers
•Setting Connectors and Jumpers

Chapter 3 System Configuration
PA -J510Series User Manual
Page: 3-2
3.1 System External I/O Ports Diagram
Rear I/O
Side I/O
USB
Type C
USB USB
COM2 COM1 DRW 2nd Dis.
1st Dis. DC In LAN HDMI
LAN COM1
COM2
HDMI
DC In
2nd Display
Port
1st Display
Port
Power USBDC OUT USB
(optional)
USB
Type C
USB 3.0 DRW
USB 2.0
USB7 Power
Button
Open up the cover from the right side of PA-J510 Box as shown
and find the Side I/O USB7 and Power Button.