protech prox PA-A310 User manual

USB Rear: 2 x USB 3.0 + 2 x USB 2.0
(optional) 2 x USB 2.0 +1 x power USB (+12V/+24V)
Side: 1 x USB 2.0
System
CPU Support Intel®Celeron® J3355 / 3455 CPU
Memory 1 x DDR3L SO-DIMM slot (up to 8GB)
Network 10/100/1000Mbps Base-T Fast Ethernet
Power Supply 60~90 Watt Power Adapter
Audio 2W Speaker
System Weight with power adaptor approx. 4 kg
Dimensions (WxHxD) 299 x 148 x 300mm
O.S. Support Windows 10
Storage
SATA1 x 2.5" HDD or SSD
1 x M.2 2242 (SATAIII interface)
I/O Ports
Serial Ports 3 x RJ45 (support +5V/12V selectable) + 1 (optional) x DB9
LAN 1 x RJ45
VGA 1 x DB15
Cash Drawer 1+1(option, with Y cable) x RJ11 (+12V or +24V selectable)
DC IN 1 x 4-pin DC Power Jack
Add-ons
Customer Display VFD, 20 columns and 2 lines, each column is 5 x 7 dots
Printer 2" or 3" easy loading thermal printer with auto-cutter
MSR & iButton JIS I,II , ISO Track1+2+3 (PS/2 interface)
Fingerprint 8-bit grayscale reader
Display
LCD 10.1" TFT LCD
Resolution 1280 x 800
Brightness 400 cd/m²
Touchscreen 10.1" Capacitive Touch panel, USB I/F (EETI controller)
Tilt Angle 24 ~ 30 degrees
Environment
EMC & Safety CE / FCC
Operating Temp. 0°C ~ 35°C (32°F ~ 95°F)
Storage Temp. -5°C ~ 60°C (23°F ~ 140°F)
Humidity 20% ~ 90%
HDMI 1 x HDMI
Line Out 1 (optional) x phone jack
All Rights Reserved. Copyright 2017
PIP1230
Specifications
If you discover any item below was damaged or lost,
please contact your vendor immediately.
Packing Checklist
PA-3122
System View
Front View
Side View
Top View
Rear View
Quarter View
PA-A310 PA-A310
PA-A310
Quick
Reference
Guide
All Rights Reserved. Copyright 2019
Ver. Q1
298.29
299.88
PA-A310
Bottom View
DC IN COM1 COM2 COM3 HDMI LAN USB1/2 USB3/4 DWR
145.90
22°
I/O View
VGA
DRW1
DRW1-1 DRW1-2
extended with
Y cable
LINE
OUT VGA
DC IN COM1 COM2 COM3 LAN
COM4
HDMI USB 1/2 USB 3/4 DWR
DWR2
(Option)
Line Out
(Option)
DC IN
COM1 COM3
COM2
LAN
HDMI USB 3.0
COM4
(Option) USB Port
(Option 1) DWR2
(Option)
DWR
Power USB
(Option 2)
USB 2.0
AC Power Cord (Optional) X 1
PA-A310 X 1
This Quick Reference Guide X 1
Driver DVD X 1
MSR Card Reader (Optional) X 1
i-Button + MSR Card Reader (Optional) X 1
X 1
Wireless LAN (IEEE 802.11 b+g) (Optional)
X 1
VFD (Optional)
Barcode Scanner (Optional) X 1

Easy Maintenance
PA-A310
Jumper Setting
Jumper Setting
All Rights Reserved. Copyright 2019
The One-of-a-kind Highly Integrated Fanless 10.1" POS Terminal
Step 1
Step 2
Step 3
Step 4
Safety Precaution
Safety Precaution
COM1 / COM2 voltage adjustment:
The voltage of external COM1 & COM2 can be adjusted via BIOS for your convenience.
The following messages are safety reminders on how to protect your system from damages,
and extend the life cycle of the system.
1. Check the Line Voltage
● Make sure the operating voltage range is between 100V and 240V AC; otherwise, the
system could be damaged.
2. Environmental Conditions
● Place your PA-A310 on a sturdy, level surface. Be sure to allow enough space around
the system to have easy access needs.
● Avoid installing the system in extremely hot or cold places.
● Avoid exposure to sunlight for a long period of time or in an airtight room.
● Also, avoid the system from any heating device or using the PA-A310 when it has been
left outdoors in a cold winter day.
● Avoid moving the system rapidly from a hot place to a cold place, and vice versa, because
condensation may occur inside the system.
● Operate the PA-A310 in strong vibration may cause hard disk failure.
● Do not place the system too close to any radio-active device. Radio-active device may
cause signal interference.
● Always shut down the operating system before you turn off the power.
3. Handling
● Avoid placing heavy objects on the top of the system.
● Do not turn the system upside down. This may cause the hard drive to malfunction.
● Do not allow any objects to fall into this product.
● If water or other liquid spills into this product, unplug the power cord immediately.
4. Good Care
● When the outside case gets stained, remove the stains using neutral washing agent with
a dry cloth.
● Never use strong agents such as benzene and thinner to clean the surface of the case.
● If heavy stains are present, moisten a cloth with diluted neutral washing agent or alcohol
and then wipe thoroughly with a dry cloth.
● If dust is accumulated on the case surface, remove it using a special vacuum cleaner for
computers.
● Do not replace the motherboard battery by yourself, or serious damage may occur.
CAUTION! Danger of explosion if battery is incorrectly replaced. Replace only with the same
or equivalent type recommended by the manufacturer. Dispose of used batteries according to
the manufacturer’s instructions.
WARNING! Some internal parts of the system may have high electrical voltage. Therefore we
strongly recommend qualified engineers open and disassemble the system. The LCD and
touchscreen are easily breakable; please handle them with extra care.
JP6, JP7, JP8
COM4 / i-Button
Function Selection
I-BUT
1
(default)
COM4
1
JP5 LVDS Backlight
Enable Voltage
(default)
1
3.3V 5V
1
DRW1 USB3_1 USB1 LAN1 HDMI1 COM3 COM2 COM1 DC_IN1
COM1_1COM2_1
JLPC1
JP8
JP7
JP6
COM4
JP_VDD1
JP5
JP_USB3_2
JP_USB3_1
USB3_2
JP_USB5
USB5
USB6 SATA1
SATA_PWR1
OUT_5V
SO_DIMM1
HS1
EDP1 PS2
M2_E
M2_M
M2 M1
FAN_1 JUSB7
SW3
USB7
OUT_24V OUT12V_2
OUT12V_1
JVGA1
JP_USB2
USB2
LED1SW2
BAT1
JP3
JP2
JSPK1
JP1
JAUD1
JP11
12
56
1
2
5
6
1
5
1
5
12
12
56
12
56
1
1
15
6
12
2930
1
6
1
1
1 2
15 16
12
56
1
11
1
1
1
12
78
1
2
3
4
1
1
1
1
5
6
10
1
1
2
9
10
11
1
1
1 5
610
15
610
SW1
5
8
4
1
M.2 SSD
M.2 Wi-Fi
SP1
I-BUT1
1
TOUCH1
1
5
LVDS1
2
1
30
29
17
JP_VDD1
LVDS Voltage Selection
(default)
1
3.3V 5V
1
JINV1
JP4
16
2
5
1
JP_USB3_1 / JP_USB3_2
USB3 Port Selection
USB3_1
(default)
12
56
USB3_2
12
56
JP_USB2
USB2 Port Selection
M.2 USB
1 2
5 6
(default)
USB2
1 2
5 6
JP11 Cash Drawer Selection
(default)
1 Drawer &
12V
2
6
12
56
1 Drawer &
24V
5
12
6
2 Drawer &
12V
2 Drawer &
24V
12
56
JP4 LVDS Sequence Control Selection
From CH7511From CPU
(default)
1
2
5
6
1
2
5
6
JP_USB5
USB5 Port Selection
1
2
5
6
USB5
(default)
JP3 Clear CMOS Data
Selection
Normal
1
(default)
Clear CMOS
1
JP1
Force DNX FW Load
Normal
(default) Force
1
2
3
4
1
2
3
4
JP1 Flash
Descriptor Override
Normal
(default)
1
2
3
4
Override
1
2
3
4