protech prox PA-J511 User manual

USER
MANUAL
PA-J511
15" High Performance
POS Terminal
PA-J511M2

PA-J511 15” High
Performance POS Terminal
COPYRIGHT NOTICE & TRADEMARK
All trademarks and registered trademarks mentioned herein are the
property of their respective owners.
This manual is copyrighted in Apr. 2023. You may not reproduce or
transmit in any form or by any means, electronic, or mechanical,
including photocopying and recording.
DISCLAIMER
This user’smanual is meant to assist users in installing and setting up
the system. The information contained in this document is subject to
change without any notice.
CE NOTICE
This is a class A product. In a domestic environment this product may
cause radio interference in which case the user may be required totake
adequate measures.

FCC NOTICE
This equipment has been tested and found to comply with the limits for
a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
You are cautioned that any change or modifications to the equipment
not expressly approve by the party responsible for compliance could
void your authority to operate such equipment.
CAUTION: Danger of explosion may occur when the battery
is incorrectly replaced. Replace the battery
only with the
same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer’s
instructions.
WARNING: Some internal parts of the system may have
high electrical voltage. We strongly recommend that only
qualified engineers are allowed to service and disassemble
the system. If any damages should occur on the system and
are caused by unauthorized servicing, it will not be covered
by the product warranty.

i
Contents
Revision History ............................................................................................. v
1Introduction ......................................................................................... 1-1
1.1 About This Manual ..................................................................... 1-2
2Getting Started .................................................................................... 2-1
2.1 Package List............................................................................... 2-2
2.2 System Overview ....................................................................... 2-3
2.2.1 Panel PC ............................................................................. 2-3
2.2.2 Normal Stand Only.............................................................. 2-4
2.2.3 Normal Stand with 10.1" 2nd Display ................................. 2-5
2.3 System Specifications ................................................................ 2-6
2.4 Safety Precautions ..................................................................... 2-8
3System Configuration......................................................................... 3-1
3.1 System External I/O Ports Diagram ........................................... 3-2
3.2 Mainboard Component Locations & Jumper Setting ................. 3-3
3.3 How to Set Jumpers................................................................... 3-4
3.4 Main Board Connector & Jumper Quick Reference Table ......... 3-6
3.5 Setting Main Board Connectors and Jumpers ........................... 3-7
3.5.1 Power Switch ...................................................................... 3-7
3.5.2 DC IN Connector (DC In) .................................................... 3-7
3.5.3 1st Display Port (MDP1) ..................................................... 3-8
3.5.4 COM Ports (COM1, COM2) ................................................ 3-9
3.5.5 COM Connector (COM3, COM4)........................................ 3-9
3.5.6 LAN Port (LAN1) ............................................................... 3-11
3.5.7 USB 2.0 Port (USB4) ........................................................3-12

ii
3.5.8 Dual USB 2.0 Ports (USB2).............................................. 3-13
3.5.9 Dual USB 3.0 Ports (USB1).............................................. 3-13
3.5.10 2nd Display Port (MDP2) .................................................. 3-14
3.5.11 HDMI Port Connector (HDMI1).........................................3-15
3.5.12 Cash Drawer Port (DRW) .................................................3-16
3.5.13 Internal USB Wafer (JUSB9) ............................................3-19
3.5.14 Internal USB Wafer (JUSB7) ............................................3-20
3.5.15 M.2 M-Key Connector for SSD (M2_M1)..........................3-21
3.5.16 M.2 M-Key Connector for SSD (M2_M2)..........................3-23
3.5.17 M.2 E-Key Connector for Wi-Fi (M2_E1) ..........................3-25
3.5.18 Speaker Wafer (JSPK1).................................................... 3-27
3.5.19 Microphone Connector (JMIC1)........................................ 3-27
3.5.20 Power Output 24V Wafer (J24V_OUT1)........................... 3-27
3.5.21 System LED Wafer (JSYS_LED1) .................................... 3-28
3.5.22 CPU Fan Wafer (CPU_FAN1)...........................................3-28
3.5.23 Power Button Wafer (JPWRBTN1) ................................... 3-29
3.5.24 Battery Wafer (JBAT1) ......................................................3-29
3.5.25 System Reset Wafer (JRST1)........................................... 3-29
3.5.26 Cash Drawer Voltage Selection (JP3) ..............................3-30
3.5.27 Clear CMOS Data Selection (JCMOS1) ...........................3-31
3.6 A/D Board Component Locations & Jumper Setting................3-32
3.7 A/D Board Connector & Jumper Quick Reference Table .........3-33
3.8 Setting A/D Board Connectors and Jumpers ........................... 3-34
3.8.1 1st Display Port Connector (MDP1).................................. 3-34
3.8.2 Embedded DisplayPort Connector (JEDP2).....................3-35
3.8.3 Speaker Connector (JSPK1) ............................................3-36
3.8.4 Inverter Connector (JINV1)............................................... 3-36
3.8.5 LVDS Connector (LVDS1).................................................3-37
3.8.6 USB 2.0 Connector (JUSB1, JUSB2, JUSB3)..................3-38

iii
3.8.7 Backlight Voltage Selection (JP_INV1).............................3-39
3.8.8 LVDS Panel Voltage Control Selection (JP_VDD1).......... 3-39
3.8.9 LVDS Backlight Control Selection (JP1) ........................... 3-40
4Software Utilities................................................................................. 4-1
4.1 Introduction................................................................................. 4-2
4.1.1 Installing Intel®Chipset Software Installation Utility ........... 4-3
4.1.2 Installing Graphics Driver Utility.......................................... 4-4
4.1.3 Intel®Management Engine Components Installer Installation.
........................................................................................... 4-5
4.1.4 Installing LAN Driver Utility ................................................. 4-6
4.1.5 Installing Sound Driver Utility.............................................. 4-7
5BIOS SETUP ........................................................................................ 5-1
5.1 Introduction................................................................................. 5-2
5.1.1.1 Accessing Setup Utility ................................................... 5-4
5.1.2 Main .................................................................................... 5-7
5.1.3 Advanced ............................................................................ 5-8
5.1.3.1 Advanced - CPU Configuration..................................... 5-10
5.1.3.2 Advanced - PCH-FW Configuration.............................. 5-11
5.1.3.3 Advanced - Trusted Computing ....................................5-12
5.1.3.4 Advanced - ACPI Settings ............................................ 5-13
5.1.3.5 Advanced - F81967 Super IO Configuration ................ 5-14
5.1.3.6 Advanced - Hardware Monitor ...................................... 5-19
5.1.3.7 Advanced - F81967 Watchdog .....................................5-22
5.1.3.8 Advanced - S5 RTC Wake Settings.............................. 5-23
5.1.3.9 Advanced - USB Configuration..................................... 5-24
5.1.3.10 Advanced - Network Stack Configuration ..................... 5-25
5.1.3.11 Advanced - NVMe Configuration ..................................5-26
5.1.4 Chipset ..............................................................................5-27
5.1.4.1 System Agent (SA) Configuration ................................. 5-28

iv
5.1.4.2 PCH IO Configuration ...................................................5-30
5.1.5 Security ............................................................................. 5-36
5.1.6 Boot................................................................................... 5-38
5.1.7 Save & Exit ....................................................................... 5-40
Appendix A System Diagrams....................................................A-1
PPC Memory Maintenance.......................................................................A-2
PPC M.2 2280 Maintenance.....................................................................A-4
PA-J511 Memory Maintenance ................................................................A-5
PA-J511 M.2 2280 Maintenance ..............................................................A-7
How To Turn System Touchscreen ...........................................................A-8
2nd Display Assembly ..............................................................................A-9
VFD Module Assembly ...........................................................................A-12
iButton Module Assembly .......................................................................A-14
Fingerprint Module Assembly .................................................................A-15
Barcode Scanner Assembly ...................................................................A-16
MSR Module Assembly ..........................................................................A-17
POS Type Assembly Exploded Diagram ................................................A-18
PPC Type Assembly Exploded Diagram ................................................A-19
Appendix B Technical Summary ................................................B-1
Block Diagram ..........................................................................................B-2
Interrupt Map ............................................................................................B-3
I/O MAP ..................................................................................................B-18
Memory Map...........................................................................................B-20
Configuring WatchDog Timer .................................................................B-22
Flash BIOS Update.................................................................................B-26

v
Revision History
The revision history of PA-J511 User Manual isdescribed below:
Version No. Revision History Date
M2 The description of Section 3.5.12 Cash Drawer
Port (DRW) has been revised. (Page 3-16) 2023/04/25
M1 Initial Release 2023/4/10

PA -J511SERIES USER MANUAL
Page: 1-1
1Introduction
This chapter provides the introduction for PA-J511 system
as well as the framework ofthe user manual.
The following topic is included:
•About This Manual

Chapter 1 Introduction
PA -J511SERIES USER MANUAL
Page: 1-2
1.1 About ThisManual
Thank you for purchasing our PA-J511system. The PA-J511is an updated system
designed to be comparable with the highest performance of IBM AT
personal computers. The PA-J511provides faster processing speed, greater
expandability and can handle more tasks than before. This manual is designed to
assist you how to install and set up the whole system. It contains 5 chapters and 2
appendixes. Users can configure the system according to their own needs. This user
manual is intended for service personnel with strong hardware background. It is
not intended for general users.
The following section describes the structure of this user manual.
Chapter 1 Introduction
This chapter introduces the framework of this user manual.
Chapter 2 Getting Started
This chapter describes the package contents and system specifications,and illustrates
the physical appearances for PA-J511system. Read the safety reminders carefully on
how to take care of your system properly.
Chapter 3 System Configuration
This chapter describes the locations and functions of the system main board
components. You will learn how toproperly configure the connectors and system
configuration jumpers on the main board and configure the system tomeet your own
needs.
Chapter 4 Software Utilities
This chapter introduces how to install Intel Chipset Software Installation Utility,
Graphics Driver Utility, Intel Management Engine Components Installer Driver
Utility, LAN Driver Utility, Serial IO Driver Utility and Sound Driver Utility.
Chapter 5 BIOS Setup
This chapter provides BIOS setup information.
Appendix A System Diagrams
This appendix provides the exploded diagrams and part numbers of PA-J511.
Appendix B Technical Summary
This appendix provides the information about the system block diagram, allocation
maps for system resources, Watchdog Timer Configuration and Flash BIOS Update.

PA -J511Series User Manual
Page: 2-1
2Getting Started
This chapter provides the introduction for the PA-J511
system as well as the framework ofthe user manual.
The following topic is included:
•About This Manual
•POS System Illustration
•System Specifications
•Safety precautions
Experienced users can jump to Chapter 3 on page 3-1
for a quick start.

Chapter 2 Getting Started
PA -J511Series User Manual
Page: 2-2
2.1 Package List
If you discover any of the items listed below are damaged or lost, please contact
your local distributor immediately.
Item Q’ty
PA-J511 POS System 1
Manual / Driver DVD 1
Power Adapter 1
Power Cord 1

Chapter 2 Getting Started
PA -J511Series User Manual
Page: 2-3
2.2 System Overview
Unit: mm
2.2.1 Panel PC
Front View Rear View
Side View
342
270
136
VESA 75
VESA 75
24.4
60.4

Chapter 2 Getting Started
PA -J511Series User Manual
Page: 2-4
2.2.2 Normal Stand Only
Unit: mm
Front View Rear View
Side View
342
270
322.4
DC In LAN
1st Dis. HDMI
Type C
COM2 COM1 DRW2nd Dis.
24.4

Chapter 2 Getting Started
PA -J511Series User Manual
Page: 2-5
2.2.3 Normal Stand with 10.1" 2nd Display
Unit: mm
Front View Rear View
Side View
342
270
322.4
DC In LAN
1st Dis. HDMI
Type C
COM2 COM1 DRW2nd Dis.
198.8
24.4
20.2

Chapter 2 Getting Started
PA -J511Series User Manual Page: 2-6
2.3 System Specifications
2.3 System Specifications 2.3 System Specifications
System
CPU Support  Intel
®
Celeron
®
J6412 (fanless)
Memory  1 x DDR4 260-pin SO-DIMM slot (up to 16GB)
Network  1 x RJ45, 10/ 100/1000 Mbps
 1 x M.2 (Key E, 2230)
Power Supply  1 x 60/90 watt power adapter
Audio  1 x 2W speaker
System Weight
 POS + 2nd Display: approx. 5.3 kg
(w/o power adapter)
 POS: 4.3 kg
 PPC: 3.9 kg
Dimensions
(W x H x D)
 POS + 2nd Display: 342 x 291 x 237 mm
(with 45 degree)
 POS: 342 x 270 x 195 mm (with 45 degree)
 PPC type: 342 x 270 x 60 mm
O.S. Support  Windows 11 / Windows 10 IoT Enterprise
Storage
SATA  1 x M.2 2242 / 1 x M.2 2280, SATA interface
I/O Ports
Display
 1 x Mini DP for Primary display (for Protech original
display only)
 1 x Mini DP for 2nd display (for Protech original
display only)
 1 x HDMI 1.4
USB  Rear I/O: 3+1 (optional) x USB 2.0 / 2 x USB 3.1
 Side I/O: 1 x USB 2.0
Serial Ports  1 x RJ45 (all support 5V/12V selectable under BIOS)
(RS-232 interface)
LAN  1 x 2.5G LAN (RJ45)
Cash Drawer  1 x RJ11 (+12V or +24V selectable)
(default at +24V)
DC In  1 x 4-pin DC power jack (4pin, DIN)
Option  1 x USB 2.0 or 1 x 24V Power USB (1A) or
1 x DC Out (1A) or 1 x RJ-45 (RS-232 interface)

Chapter 2 Getting Started
PA -J511Series User Manual
Page: 2-7
Add-ons
Customer Display VFD kit, 20 columns x 2 lines STN LCD display
MSR JIS I,II, ISO Track1+2+3 (USB interface)
2nd Display 10.1” with P-cap touch
Fingerprint Silicon Fingerprint Module (USB interface)
iButton iButton module (USB interface)
Scanner 2D: PDF417, QR Code, Micro QR, Data Matrix
Display
Primary Display 15” IPS LCD (Resolution: 1024 x 768)
Brightness: 400 cd/m²
Touchscreen Bezel-free projected capacitive
2nd Display 10.1” Monitor with Touch
Environment
EMC & Safety CE / FCC
Operating Temp. 0°C ~ 35°C (32°F ~ 95°F)
Storage Temp. -5°C ~ 60°C (23°F ~ 140°F)
Humidity 20% ~ 90%

Chapter 2 Getting Started
PA -J511Series User Manual
Page: 2-8
2.4 Safety Precautions
Before operating this system, read the following information carefully to protect your
systems from damages, and extend the life cycle of the system.
1. Check the Line Voltage
•The operating voltage for the power supply should be within the range of 100V
to 240V AC; otherwise, the system may be damaged.
2. Environmental Conditions
•Place your PA-J511on a sturdy,level surface. Be sure to allow enough space
around the system tohave easy accessneeds.
•Avoid installing your PA-J511system inextremely hot orcold places.
•Avoid direct sunlight exposure for a long period of time (for example, ina
closed car insummer time. Also avoid the system from anyheating device.). Or
do not use PA-J511when it has been left outdoors in a cold winter day.
•Bear inmind that the operating ambient temperature is between 0°C and 35°C
(32°F and 95°F).
•Avoid moving the system rapidly from a hot place to a cold place, andvice
versa, because condensation may occur inside the system.
•Protect your PA-J511from strong vibrations which may cause hard disk failure.
•Do not place the system tooclose to any radio-active device. Radio-active
device may cause signal interference.
•Always shut down the operating system before turning off the power.
3. Handling
•Avoid placing heavy objects on the top of the system.
•Do notturn the system upside down. This may cause the hard drive to
malfunction.
•Do not allow any objects to fall into this device.
•If water orother liquid spills into thedevice,unplug the power cord
immediately.

PA -J511Series User Manual
Page: 3-1
3System Configuration
This chapter provides the information for the PA-J511 system.
It describes the jumper and connector settings, component
locations, and pin assignment.
The following topics are included:
•System External I/O Port Diagram
•Mainboard Component Locations & Jumper Setting
•How to Set Jumpers
•Setting Connectors and Jumpers

Chapter 3 System Configuration
PA -J511Series User Manual
Page: 3-2
3.1 System External I/O Ports Diagram
Rear I/O
Side I/O
DC OUT USB Power USB COM
LAN
COM1
COM2
HDMI
DC In 2nd Display
Port
1st Display
Port
(optional)
USB 2.0
USB 3.0 DRW
USB 2.0
1st Dis. DC In LAN HDMI
USB USB
COM2 COM1 DRW 2nd Dis.
USB
USB7 Power
Button
Open up the cover from the right side of PA-J511 Box as shown
and find the Side I/O USB7 and Power Button.