protech PA-5685 User manual

USER
MANUAL
PA-5685
15.6" POS Terminal
Powered by Intel 7th
Kabylake U series
PA-5685 M3

PA-5685 15.6”POSTerminal
Powered by Intel 7th Kabylake U
series
COPYRIGHT NOTICE & TRADEMARK
All trademarks and registered trademarks mentioned herein are the
property of their respective owners.
This manual is copyrighted in Jun. 2018. You may not reproduce or
transmit in any form or by any means, electronic, or mechanical,
including photocopying and recording.
DISCLAIMER
This user‟s manual is meant to assist users in installing and setting up
the system. The information contained in this document is subject to
change without any notice.
CE NOTICE
This is a class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take
adequate measures.

FCC NOTICE
This equipment has been tested and found to comply with the limits for
a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
You are cautioned that any change or modifications to the equipment
not expressly approve by the party responsible for compliance could
void your authority to operate such equipment.
CAUTION: Danger of explosion may occur when the battery
is incorrectly replaced. Replace the battery only with the
same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer’s
instructions.
WARNING: Some internal parts of the system may have
high electrical voltage. We strongly recommend that only
qualified engineers are allowed to service and disassemble
the system. If any damages should occur on the system and
are caused by unauthorized servicing, it will not be covered
by the product warranty.

i
Contents
Revision History ............................................................................................vi
1 Introduction .........................................................................................1-1
1.1 About This Manual ..................................................................... 1-2
1.2 Package List ............................................................................... 1-3
1.3 System Overview ....................................................................... 1-4
1.4 System Specifications ................................................................ 1-9
1.5 Safety Precautions ................................................................... 1-16
2 System Configuration.........................................................................2-1
2.1 System External I/O Port & Pin Assignment .............................. 2-2
2.2 Mainboard Component Locations & Jumper Setting ................. 2-3
2.3 How to Set Jumpers ................................................................... 2-4
2.4 Setting Connectors and Jumpers ............................................... 2-6
2.4.1 Power Switch ...................................................................... 2-6
2.4.2 VGA Port ............................................................................. 2-6
2.4.3 HDMI Port ........................................................................... 2-7
2.4.4 DC IN Port ........................................................................... 2-7
2.4.5 2nd Display Power Port ...................................................... 2-8
2.4.6 Printer Power Port (Optional) .............................................. 2-8
2.4.7 Cash Drawer Port ............................................................... 2-8
2.4.8 COM Port ............................................................................ 2-9
2.4.9 COM Ports ........................................................................ 2-11
2.4.10 USB Port ........................................................................... 2-11
2.4.11 LAN Port ........................................................................... 2-12
2.4.12 COM Connectors .............................................................. 2-13
2.4.13 Enables COM4 Ports ........................................................ 2-13
2.4.14 SPI(BIOS) Flash Wafer ..................................................... 2-14

ii
2.4.15 Audio Jack ........................................................................ 2-14
2.4.16 DRW Ports ........................................................................ 2-15
2.4.17 USB Connectors ............................................................... 2-19
2.4.18 Enable to Jusb8 ................................................................ 2-20
2.4.19 Selection of USB2.0 & M.2_E ........................................... 2-20
2.4.20 Power Connector .............................................................. 2-21
2.4.21 Power for Thermal Printer Connector ............................... 2-21
2.4.22 Fan Connector .................................................................. 2-21
2.4.23 i-Button Connector ............................................................ 2-22
2.4.24 Audio Connector ............................................................... 2-22
2.4.25 Speaker Connector ........................................................... 2-22
2.4.26 Power indication LED connector ....................................... 2-23
2.4.27 Power Switch .................................................................... 2-23
2.4.28 System Reset .................................................................... 2-23
2.4.29 RTC Coin Battery Wafer ................................................... 2-24
2.4.30 Clear RTC Data Selection Connector ............................... 2-24
2.4.31 Clear CMOS data.............................................................. 2-25
2.4.32 Unlock the Entire SPI Flash (override descriptor setting) . 2-25
2.4.33 SATA 3.0 Connector .......................................................... 2-26
2.4.34 HDD Power Port ............................................................... 2-26
2.4.35 eDP Connector ................................................................. 2-27
2.4.36 VCC Selection for eDP ..................................................... 2-28
2.4.37 M.2 M-Key ......................................................................... 2-29
2.4.38 M.2 E-Key ......................................................................... 2-30
2.5 Peripheral Boards Component Location, Pin Define & Jumper
Setting ...................................................................................... 2-31
2.5.1 Printer Board: PDAC-3100 ............................................... 2-31
2.5.1.1 Power Supply Connector ................................................. 2-32
2.5.1.2 RS-232 Interface Connector ............................................ 2-32
2.5.1.3 Auto-Cutter Connector .................................................... 2-33

iii
2.5.1.4 USB Connector................................................................ 2-33
2.5.1.5 Thermal Head / Motor / Sensor Connector ..................... 2-34
2.5.1.6 Thermal Assignment Connector ...................................... 2-36
2.5.2 Printer Board: MB-1030 Series ......................................... 2-37
2.5.2.1 Power Supply Connector ................................................. 2-38
2.5.2.2 RS-232 Interface Connector ............................................ 2-38
2.5.2.3 Thermal Head / Motor / Sensor Connector ..................... 2-39
2.5.2.4 Auto-Cutter Connector .................................................... 2-41
2.5.2.5 Paper-Near-END Sensor Connector ............................... 2-42
2.5.2.6 USB Interface Connector ................................................ 2-42
2.5.2.7 Thermal Assignment Connector ...................................... 2-43
2.5.3 Printer Board: MB-1011 & MB-1013 ................................. 2-44
2.5.3.1 Power Supply Connector ................................................. 2-45
2.5.3.2 RS-232 Interface Connector ............................................ 2-45
2.5.3.3 Auto-Cutter Connector .................................................... 2-46
2.5.3.4 USB Interface Connector ................................................ 2-46
2.5.3.5 Thermal Head / Motor / Sensor Connector ..................... 2-47
2.5.3.6 Thermal Assignment Connector ...................................... 2-49
2.6 VFD Board Component Locations & Pin Assignment .............. 2-50
2.7 MSR Board Component Locations & Pin Assignment ............. 2-51
2.8 System Cabling ........................................................................ 2-53
3Software...............................................................................................3-1
3.1 Driver Disc .................................................................................. 3-3
3.1.1 Installing Intel® Chipset Software Installation Utility ........... 3-3
3.1.2 Intel® Management Engine Components Installer .............. 3-4
3.1.3 Microsoft Hotfix Driver installation ...................................... 3-5
3.1.4 Installing Graphics Driver Utility .......................................... 3-6
3.1.5 Installing LAN Driver Utility ................................................. 3-7
3.1.6 Installing Sound Driver Utility .............................................. 3-8

iv
3.1.7 Installing Intel® Serial I/O Driver Utility ................................ 3-9
3.2 API ............................................................................................ 3-10
3.2.1 API Package Content ....................................................... 3-10
3.2.2 API Procedure ................................................................... 3-11
3.2.3 Cash Drawer ..................................................................... 3-14
3.2.4 Watchdog .......................................................................... 3-15
3.3 API Function ............................................................................. 3-16
3.3.1 Cash Drawer Function ...................................................... 3-16
3.3.2 Watch Dog Function ......................................................... 3-17
3.4 Peripheral Devices ................................................................... 3-18
3.4.1 Printer Board: MB-1030 .................................................... 3-18
3.4.1.1 Command ........................................................................ 3-18
3.4.1.2 OPOS Printer Driver ........................................................ 3-67
3.4.2 VFD: MB-4103 (RS-232) . ................................................ 3-75
3.4.2.1 Command List ................................................................. 3-75
3.4.2.2 OPOS Driver .................................................................... 3-76
3.4.3 MSR: MB-3012 (PS/2) ...................................................... 3-81
3.4.3.1 OPOS Driver .................................................................... 3-81
3.4.4 MSR: GIGA-TMS MJR243R (RS-232) ............................. 3-87
3.4.4.1 Command List ................................................................. 3-87
3.4.4.2 OPOS MSR Register ....................................................... 3-90
3.4.4.3 OPOS MSR Tester .......................................................... 3-97
3.5 BIOS ....................................................................................... 3-101
3.5.1 BIOS Setup ..................................................................... 3-101
3.5.1.1 Accessing Setup Utility .................................................. 3-103
3.5.2 Main ................................................................................ 3-105
3.5.3 Advanced ........................................................................ 3-106
3.5.3.1 Advanced - CPU Configuration ..................................... 3-107
3.5.3.2 Advanced - SATA Configuration .................................... 3-109

v
3.5.3.3 Advanced - PCH-FW Configuration .............................. 3-110
3.5.3.4 Advanced - Trusted Computing ..................................... 3-111
3.5.3.5 Advanced - ACPI Settings ............................................. 3-113
3.5.3.6 Advanced - F81866 Super IO Configuration ................. 3-114
3.5.3.7 Advanced - Hardware Monitor ....................................... 3-121
3.5.3.8 Advanced - F81866 Watchdog ...................................... 3-123
3.5.3.9 Advanced - USB Configuration ..................................... 3-124
3.5.3.10 Advanced - Network Stack Configuration .................. 3-125
3.5.4 Chipset ............................................................................ 3-126
3.5.4.1 System Agent (SA) Configuration .................................. 3-127
3.5.4.2 PCH IO Configuration .................................................... 3-129
3.5.5 Security ........................................................................... 3-131
3.5.6 Boot ................................................................................. 3-133
3.5.7 Save & Exit ..................................................................... 3-134
3.6 Configuring WatchDog Timer ................................................. 3-136
3.7 Update Procedure .................................................................. 3-139
3.8 Appendix ................................................................................ 3-142
4System Diagram..................................................................................4-1
4.1 System Diagram ......................................................................... 4-2

vi
Revision History
The revision history of PA-5685 User Manual is described below:
Version No.
Revision History
Date
M1
Initial Release
2018/6

PA-5685 User Manual
Page: 1-1
1 Introduction
This chapter provides the introduction for the PA-5685
system as well as the framework of the user manual.
The following topic is included:
• About This Manual
• POS System Illustration
• System Specifications
• Safety precautions
Experienced users can jump to chapter 2 on page 2-1
for a quick start.

Chapter 1 Introduction
PA-5685 User Manual
Page: 1-2
1.1 About This Manual
Thank you for purchasing our PA-5685 Series System. The PA-5685 is an updated
system designed to be comparable with the highest performance of IBM AT personal
computers. The PA-5685 provides faster processing speed, greater expandability and
can handle more tasks than before. This manual is designed to assist you how to
install and set up the whole system. It contains 4 chapters. Users can configure the
system according to their own needs.
Chapter 1 Introduction
This chapter introduces you to the background of PA-5685 user manual. It also
includes the physical illustrations and specifications for the PA-5685 system. Read the
safety reminders carefully on how to take care of your system properly.
Chapter 2 System Configuration
This chapter outlines the locations of the motherboard, VFD, MSR components and
their respective functions. You will learn how to set the jumpers and configure the
system to meet your own needs.
Chapter 3 Software Utilities
This chapter contains helpful information for proper installations of the “DRIVER”
which comes in a DVD-ROM format, how to change the AMI BIOS configurations,
Watchdog Timer Configuration, Flash BIOS Update and ACPI functions list.
Chapter 4 System Diagrams
This chapter provides the exploded diagrams and part numbers of the PA-5685.
CAUTION
FOR YOUR TROUBLESHOOTING NEEDS,
CONSULT THESE MODULES' USER'S GUIDES
INCLUDED IN PA-5685 USER MANUALFILE.
YOU MAY ALSO CONTACT OUR SERVICE
WINDOW FOR TECHNICAL ASSISTANCE.

Chapter 1 Introduction
PA-5685 User Manual
Page: 1-3
1.2 Package List
If you discover any of the items listed below are damaged or lost, please
contact your local distributor immediately.
Item
Q’ty
PA-5685 POS System
1
Manual / Driver DVD
1

Chapter 1 Introduction
PA-5685 User Manual
Page: 1-4
1.3 System Overview
Panel-PC
Front View
Rear View
Left Side
Right Side
Top View
391
250
48

Chapter 1 Introduction
PA-5685 User Manual
Page: 1-5
Small Stand
Front View
Rear View
Side View Quarter View
391
218
268
247
48
Adjustable angle
0~70 degrees

Chapter 1 Introduction
PA-5685 User Manual
Page: 1-6
Big Stand
Front View
Rear View
Side View Quarter View
391
345
240

Chapter 1 Introduction
PA-5685 User Manual
Page: 1-7
Printer Stand
Front View
Rear View
Side View Quarter View
391
345
240
50°

Chapter 1 Introduction
PA-5685 User Manual
Page: 1-8
Caution:
The correct method of
"Closing Printer-Door".
Please refer to around
drawings.

Chapter 1 Introduction
PA-5685 User Manual
Page: 1-9
1.4 System Specifications
System
CPU Supports
Core-i3 7100U
Intel® Kaby Lake Pentium 4415U
Celeron 3965U
Memory
1 x DDR4 SO-DIMM socket (up to 16GB)
Network
10/100/1000 Ethernet
Power Supply
60~90 Watt power adapter
Audio
2W speaker
Weight
approx. 6kg with Normal-Stand bundled power
adaptor
Dimensions
391 x 247 x 48mm (W x H x D)
OS support
Windows IoT10
BIOS
AMI SPI BIOS, 8 Mbits with VGA BIOS
RTC Accuracy
3 days ± 3 seconds
SATA1
1 x 2.5" HDD or SSD
SATA2
1 x M.2 SSD
I/O Ports
USB
On rear
2 x USB 2.0
2 x USB
on side bezel
1 x USB 2.0
Serial Ports
1 x DB9
2 x RJ45
1 x RJ45 (all support + 5V / 12V selectable)
(optional)
LAN
1 x RJ45, GIGA
VGA
1 x DB15
HDMI 1 x HDMI port
Cash Drawer
1 + 1 (option, with Y cable) x RJ11 (12V / 24V
selectable)
HDD slot
1 x 2.5" HDD / SSD maintenance slot
DC In
1 x 4-pin DC power jack
DC12V Out
1 x 3-pin connector for Protech 2nd display
DC 24V Out
1 x 4-pin connector for Protech Embedded
printer Stand
Line Out
1 x 3.5mm phone jack

Chapter 1 Introduction
PA-5685 User Manual
Page: 1-10
MIC
 1 x 3.5mm phone jack
Environment
EMC & Safety
 CE / FCC
Operating Temp.
 0 ~ 35° C
Storage Temp.
 -5 ~ 60° C
Humidity
 20 ~ 90%
Display
LCD
 15.6" TFT LCD
Resolution
 1366 x 768
Brightness
 220 cd/m²
Touchscreen
 Bezel-Free Projected Capacitive
Brightness(cd/m2)
P1 / 167.3
P2 / 195.6
P3 / 189.2
P4 / 158.6
P5 / 191.4
AVR. 180;
MIN: 160

Chapter 1 Introduction
PA-5685 User Manual
Page: 1-11
Power Consumption (AC): Power Supply: 60~90 Watt power adapter
System
Status
OFF
DLE
Working
Without
Embedded
Printer-Stand
With
Embedded
Printer-Stand
Burn-in Test Loading
set / CPU / HDD /
Memory
Shut
Down
Standby
Full loading
Dummy
COM
12V / 1A
1
1
1
1
COM
12V / 0.5A
1
1
1
1
USB 2.0
5V / 0.5A
2
2
2
2
USB 3.0
5V / 0.9A
1
1
1
1
Power
Consumption
AC 1.7W
AC 45W
AC 55.4W
AC 84.2W
Certificate: CE, CE-LVD, FCC
Type
Standard
Description
EMI
EN 55022 Class A
-
EMS
EN 55024
-
IEC 61000-4-2
ESD
• 8kV air discharge
• 4kV contact discharge
IEC 61000-4-3
RS
80~1000MHz, 3V/m, 80% AM (1kHz)
IEC 61000-4-4
EFT
• AC Power Port: 1kV
• DC Power Port: 0.5kV
• Signal Ports & Telecommunication
Ports: 0.5kV