protech PA-1922 User manual

USER
MANUAL
PA-1922
Semi-SelfService
PaymentKiosk
PA-1922 M3

PA-1922 15” Semi-Self Service
Payment Kiosk With 10.4”
Customer Touch Display
COPYRIGHT NOTICE & TRADEMARK
All trademarks and registered trademarks mentioned herein are the
property of their respective owners.
This manual is copyrighted in May 201. You may not
reproduce or transmit in any form or by any means,
electronic, or mechanical, including photocopying and recording.
DISCLAIMER
This user’s manual is meant to assist users in installing and setting up
the Kiosk. The information contained in this document is subject to
change without any notice.
CE NOTICE
This is a class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take
adequate measures.

FCC NOTICE
This equipment has been tested and found to comply with the limits for
a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
You are cautioned that any change or modifications to the equipment
not expressly approve by the party responsible for compliance could
void your authority to operate such equipment.
CAUTION: Danger of explosion may occur when the battery
is incorrectly replaced. Replace the battery only with the
same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer’s
instructions.
WARNING: Some internal parts of the Kiosk may have high
electrical voltage. We strongly recommend that only qualified
engineers are allowed to service and disassemble the Kiosk.
If any damages should occur on the Kiosk and are caused by
unauthorized servicing, it will not be covered by the product
warranty. Please operate the LCD and Touchscreen with
extra care as they can break easily.

i
Contents
1 Introduction .........................................................................................1-1
1.1 About This Manual......................................................... 1-2
2 Getting Stared......................................................................................2-1
2.1 Package Contents ......................................................... 2-2
2.2 System Overview........................................................... 2-3
2.3 System Specifications.................................................... 2-7
2.4 Quick Setup................................................................... 2-8
2.4.1 Plug In AC Power Cord...................................................2-8
2.4.2 Feed / Take Notes............................................................2-9
2.4.3 Feed / Take Coins..........................................................2-10
2.4.4 Change Printer Paper....................................................2-11
2.5 Cabel Map................................................................... 2-12
2.6 Cabel Lock Position of Cube-body............................... 2-13
2.7 Cabel Illustrations........................................................ 2-13
2.8 Safety Precautions....................................................... 2-35
3 System Configuration.........................................................................3-1
3.1 01. 2D Scanner_RIOTEC FS5022J ............................... 3-2
3.2 02. 10.4 inch Touch Monitor_PHISTEK P104VR............ 3-3
3.3 03. 3-Inch Printer_EPSON Kit........................................ 3-4
3.4 04. Coin Acceptor ICT UCA ........................................... 3-6
3.5 05. Coin Hopper_Innovative SMART Hopper................. 3-9

ii
3.6 06. Note Acceptor_Innovative NV11..............................3-11
3.7 07. Note Acceptor_JCM Vega-RC Twin........................ 3-12
3.8 08. Note Acceptor_ICT NE77....................................... 3-13
3.9 09. 15-Inch Panel-PC_Prox PA-6322-PPC .................. 3-15
4 Software Utilities.................................................................................4-1
4.1 Driver & SDK................................................................. 4-2
4.2 BIOS Operation ............................................................. 4-5
4.2.1 Main ...................................................................................4-9
4.2.2 Advanced ........................................................................4-10
4.2.2.1 Advanced –ACPI Settings..................................4-11
4.2.2.2 Advanced –F81866 Super IO Configuration...... 4-12
4.2.2.3 Advanced –Hardware Monitor........................... 4-18
4.2.2.4 Advanced –F81866 Watchdog.......................... 4-19
4.2.2.5 Advanced –CPU Configuration ......................... 4-20
4.2.2.6 Advanced –IDE Configuration........................... 4-22
4.2.2.7 Advanced –OS Selection.................................. 4-23
4.2.2.8 Advanced –CSM Configuration......................... 4-24
4.2.2.9 Advanced –USB Configuration.......................... 4-25
4.2.3 Chipset.............................................................................4-27
4.2.3.1 North Bridge....................................................... 4-28
4.2.3.2 South Bridge...................................................... 4-30
4.2.4 Security............................................................................4-31
4.2.5 Boot..................................................................................4-33
4.2.6 Save & Exit......................................................................4-34
4.3 Configuring Watchdog Timer........................................ 4-36
4.4 Flash BIOS Update...................................................... 4-38

iii
4.5 Optional Devices for PA-6322...................................... 4-38
4.5.1 MB-3102 (PS/2) MSR OPOS Driver...................... 4-41
4.5.2 MSR: GIGA-TMS MJR243 (RS-232)..................... 4-45
4.5.2.1 Commands List.................................................. 4-45
4.5.2.2 OPOS MSR Register ......................................... 4-48
4.5.2.3 OPOS MSR Tester............................................. 4-53
4.5.3 Optional Fingerprint Driver Utility.................................4-57
4.5.3.1 Installing Fingerprint Driver...........................................4-57
5 System Diagrams................................................................................5-1

PA-1922 SERIES USER MANUAL
Page: 1-1
1 Introduction
This chapter provides the introduction for the PA-1922
Kiosk as well as the framework of the user manual.
The following topics are included:
• About This Manual

Chapter 1 Introduction
PA-1922 SERIES USER MANUAL
Page: 1-2
1.1 About This Manual
Thank you for purchasing our PA-1922 Semi-Self Service Payment Kiosk. The
PA-1922 is an updated system designed to be comparable with the highest
performance of IBM AT personal computers. The PA-1922 provides faster processing
speed, greater expandability and can handle more tasks than before. This manual is
designed to assist you how to install and set up the whole system. It contains four
chapters and three appendixes. Users can configure the system according to their own
needs. This user manual is intended for service personnel with strong hardware
background. It is not intended for general users.
Chapter 1 Introduction
This chapter introduces PA-1922 Kiosk general information and the framework of
PA-1922 user manual.
Chapter 2 Getting Started
This chapter includes the physical illustrations, quick setup and specifications for the
PA-1922 system. Read the safety reminders carefully on how to take care of your
system properly.
Chapter 3 System Configuration
This chapter outlines the locations of the motherboard and sensor board components
and their respective functions. You will learn how to set the jumpers and configure the
system to meet your own needs.
Chapter 4 Software Utilities
This chapter contains helpful information for proper installations of the “DRIVER &
SDK” which comes in a DVD-ROM format, how to change the AMI BIOS
configurations, and Watchdog Timer Configuration, Flash BIOS Update and ACPI
functions list.
Chapter 5 System Diagrams
This appendix provides the exploded diagrams and part numbers of the PA-1922.

PA-1922 SERIES USER MANUAL
Page: 2-1
2 Getting Started
This chapter provides the information for the PA-1922
system. It describes how to set up the system quickly and
outlines the system specifications.
The following topics are included:
• Package List
• System Overview
• System Diagram
• Quick Setup
• System Specification
• Safety Precautions
Experienced users can go to Chapter 3 System
Configuration on page 3-1 for a quick start.

Chapter 2 Getting Started
PA-1922 SERIES USER MANUAL
Page: 2-2
2.1 Package Contents
If you discover any of the items listed above are damaged or lost,
please contact your local distributor immediately.
No.
Item
Q’ty
1
PA-1922 Semi-Self Service Kiosk
1
2
PA-1922 Quick Reference Guide
1
3
Manual/Driver DVD
1
4
AC Power Cord
1

Front View
Rear View
Side View
Chapter 2 Getting Started
2.2 System Overview
Chapter 2 Getting Started
PA-1922 SERIES USER MANUAL
Page: 2-3

10.4"
Customer
Touch
Display
Maintenance Door
Printer
Drawer
15" Sales Clerk
Touch Panel-PC
Reserved space
for "Credit Card
Reader"
Maintenance
Cover
Chapter 2 Getting Started
PA-1922 SERIES USER MANUAL
Page: 2-4

Insert Coin
Scan
Insert Cash
Get receipt
Credit Card
(customer
consign)
Get change back
Coin Acceptor
Bill Acceptor
Barcode
Reader
Credit Card
Reader
Change area
Thermal
printer
For PAYMENT Device
Chapter 2 Getting Started
PA-1922 SERIES USER MANUAL
Page: 2-5

CAUTION
Chapter 2 Getting Started
PA-1922 SERIES USER MANUAL
Page: 2-6
FOR YOUR TROUBLESHOOTINGNEEDS, CONSULT
THESE MODULES’ USER’S GUIDES INCLUDED IN
PA-1922 USER MANUAL FILE, AS LISTED BELOW.
YOU MAY ALSO CONTACT OUR SERVICE WINDOW
FOR TECHNICAL ASSISTANCE.
01. 2D Scanner_RIOTEC FS5022J
02. Touch Monitor_10.4 inch PHISTEK P104VR
03. Printer_EPSON BA-T500II Control Board
03. Printer_EPSON BA-T500II Near Sensor Board
03. Printer_Epson M-T532IIAP-000 Thermal Print-Core
04. Coin Acceptor_ICT UCA
05. Coin Hopper_Innovative SMART Hopper
03. Printer_EPSON BA-T500II Control Board
06. Note Acceptor_Innovative NVII
07. Note Acceptor_JCM VEGA
08. Note Acceptor_ICT NE77_Guide
09. Panel-PC 15 inch PROX PA-6322-PPC
03. Printer_EPSON BA-T500II Near Sensor Board

2.3 System Specifications
System
Dimension 450 x 530 x540mm (W x H x D)
Weight Without packaging approx. 40kg; With packaging
approx. 50kg
Power Supply AC 100-240V available
Reserved USB 2 Type-A USB 3.0 ports located on the system rear I/O
panel
Reserved RS-232 1 RJ-45 port at Panel-PC I/O
Sales Clerk Side
Panel PC 15” 5-Wire Resistive Touch & XGA LCD
Intel® Celeron J1900 CPU; DDR3L SO-DIMM
Memory; 2.5” SATA Storage; Windows 7 Series
Optional
Vertical MSR & iButton/JIs-or II, ISO Track1+2+3;
Vertical Fingerprint / 8-bit grayscale, reader
Customer Side
Touch Display 10.4” 5-Wire Resistive Touch & XGA LCD
Note Acceptor & Recycler Capacity / Acceptor: 300 notes / Recycler: 30 notes
Coin Acceptor & Hopper Capacity / About 1 x 1300 pcs
Printer Epson 3” thermal printer module
Supports paper rolls with 80mm or 130mm
Barcode Reader 1D UPC-A, UPC-E, EAN-8, EAN-13, UCC/EAN-128,
Code 39, Code 93, Interleaved 2 of 5, Codabar,
MSI, GS1 Databar
PDF417, MicroPDF417, DataMatrix, QR Code,
MaxiCode
Environment
EMC & Safety CE / FCC
Operating Temp. 0° C ~ 35° C
Storage Temp. -20° C ~ 60° C
Humidity 20%~ 90%
printer running
Power
Consumption
AC W
AC W
AC W
AC W
Chapter 2 Getting Started
PA-1922 SERIES USER MANUAL
Page: 2-7
€
Barcode Reader 2D
Certificate
CE, CE-LVD, FCC

Chapter 2 Getting Started
2.4 Qick Setup
2.4.1 Plug In AC Power Cord
PA-1922 SERIES USER MANUAL
Page: 2-8
Maintenance
Cover
Fixing screws
15" Sales Clerk
Touch Panel-PC
Release 3 x "fixing screws"
(see above) and open the
MaintenanceCover.
Plug in AC Power Cord and
LAN cable as shown.
AC Power Cord
LAN Cable
Step 1.
Step 2.

Chapter 2 Getting Started
2.4.2 Feed / Take Notes
PA-1922 SERIES USER MANUAL
Page: 2-9
Unlock the “Maintenance
Door” with the key.
Insert paper notes into
Recycler for future payout
preparation in the direction
shown. (red arrow)
Draw out the cash box to
withdraw the paper notes. Bank
Note
Lock
Step 1.
Step 2.
Step 3.
Step 2.
Cash Box

2.4.3 Feed / Take Coins
Chapter 2 Getting Started
PA-1922 SERIES USER MANUAL
Page: 2-10
Push
Button
Unlock the "Maintenance
Door" with the key.
Lift up the "Pulling Handle"
and pull out the "Coin
Hopper".
Step 1.
Step 2.
Step 3.
Step 4.
Pulling Handle
Lock
Press the "Push Button" on the Coin Hopper
and slide to remove the top cover.
Feed or take Coins
into/from the Coin
Hopper.

Chapter 2 Getting Started
2.4.4 Change Printer Paper
PA-1922 SERIES USER MANUAL
Page: 2-11
Unlock and pull out the "Printer Drawer".
Open the "PaperHolder" and take
out the thermal paper as shown.
※The "Paper Holder" won’t open if
thermal paper have run out.
Close the "Paper Holder" and
thenchange the thermal paper roll
(section type).
※Make sure the "Paper Holder"
is closed before you feed paper.
Open
Close
Step 1.
Step 2.
Step 3.
Paper Holder
Lock

2.5 Cable Map
Chapter 2 Getting Started
PA-1922 SERIES USER MANUAL
Page: 2-12