Qlight S100R User manual

44
90dB
5020
1
Bulb Revolving Warning Light
S100R/ S100U/ S100UA
S100R - BZ - 220 - R
[Model
number] [Buzzer] [Voltage] [Color]
| | | |
• S100R
• S100U
• S100UA
• (Blank)
- No buzzer type
• BZ
-Built-in buzzer
type
• 12 - DC12V
• 24 - DC24V
• 110 -AC110V
• 220 -AC220V
R-Red
A-Amber
G-Green
B-Blue
• Protection rating : IP44
• Ambient operating temperature : -20°C to +50°C
Model
number
Voltage Current
Bulb specications
Certicate Weight Color
Volts/
Watts
Standard
Part#
S100R
DC12V 0.966A 12V10W
T16x35
15S
9
0.34kg
R-Red
A-Amber
G-Green
B-Blue
DC24V 0.566A 24V10W 10
AC110V 0.130A 12V10W 9
0.60kg
AC220V 0.065A 12V10W 9
S100U
S100UA
DC12V 0.966A 12V10W 9
0.36kg
DC24V 0.566A 24V10W 10
AC110V 0.130A 12V10W 9
0.59kg
AC220V 0.065A 12V10W 9
Ordering Specications
Thank you for purchasing Qlight’s products. Please read this user manual carefully
prior to installation and operation to ensure safe and correct use.
Precautions for Safety
Failure to follow the instructions below may cause a loss of life or serious physical injury.
1. Please remove any objects that can interrupt ventilation around the product.
2. Please turn o󰀨 the power of the product immediately if it fails to operate properly.
3. Carefully wire the product according to each product’s specication.
4. Please be careful in preventing chemicals such as thinner, benzene, etc. in contact with the surface of the product.
5. Do not apply excessive force/impact to the product.
6. Failure to follow any of the instructions above may cause malfunction or damage to the product, re, and electric shock.
Precautions for Correct Use
Failure to follow the proper instructions may cause damage to property, the product, or malfunction of the
product that would void the warranty.
1. During wiring or maintenance, please completely turn o󰀨 the power of the product. (Failure to follow this may lead to an electric shock.)
2. Do not install the product in locations that subjects it to excessive dust or water other than the conditions designated by the IP protection
ratings indicated for each product. (Failure to follow these instructions may cause a re to the product, electric shock, physical injury,
malfunction or damage to the product.)
3. Do not alter or repair this product. If maintenance or repair service is required, please contact your local Qlight contact point. (Failure to
follow these instructions may lead to re, electric shock, or product damage.)
4. Please apply the correct voltage to the product. (Failure to follow these instructions may lead to re, electric shock, or product damage.)
5. When the product is applied to a condition that may impact lives or property, please make sure to have a double safety device. (Failure to
follow this may cause damage to property, re, electric shock and loss of life.)
Product Specications
Please scan the QR code for more
detailed product information.
www.qlight.com

2
Ø10 CABLE ENTRY Ø10 CABLE ENTRY
Ø9 CABLE ENTRY
S100UAS100RS100U
132
11
149
12
PCD 60
360°/3-M4 BOLT
93
152
12
46
PCD 60
360°/3-M4 BOLT
12 155
9646
PCD 60
360°/3-M4 BOLT
Ø101 Ø101 Ø101
• External power line - UL1015 AWG18(0.75sq) × 2C 400mm
• For built-in buzzer type, there is a shared supply line for the buzzer and lighting element.
Red
Black
White
Black
Power Power
Fuse Fuse
DC AC
Parts Denition/ Installation
S100R S100U S100UA
Lens(AS)
Housing(ABS)
Flange nut
Reector
(Heat resistant ABS)
Light bulb
Flat washer
Rubber spacer
Wiring Instructions
Dimensions
(Units : mm)
• First, remove the ange nuts from bolts and place the product through the mounting surface holes.
• Fasten the ange nuts on the opposite side of the mounting surface until the product is tightened securely.

3
PCD 60
3-Ø5 HOLES
Min. Ø5 CABLE ENTRY
S100R/ S100U/ S100UA
Dimensions
S100R
S100U
S100UA
SWP125 SWM125
Mounting Hole Specications/ Bulb Replacement Instructions
• Machine holes on the mounting surface referring to the
diagram below.
■ Mounting Hole Specications
• Please wait at least 1 minute after turning o󰀨 the power
before replacing the bulb.
• In order to dissemble the bulb, please push down the bulb(①)
lightly and screw it counterclockwise.
• In order to put the bulb in to the unit, please place the bulb(①)
in the socket(②) and screw it clockwise while lightly pushing
down the bulb.
Assemble
bulb
Disassemble
bulb
■
Bulb Replacement Instructions
①
②
Installation Environment and Protection Rating
• This product is designed for use with protection rating of IP44.
• If the product is installed in locations that subject it to excessive dust or water other than the designated IP protection rating
indicated(IP44), it may cause malfunction or damage to the product.
• In case of outdoor applications, install the product in the upright position. Do not install the product horizontal or upside-
down positions where water can potentially penetrate into the product and impact it’s operation.
• For further information, please visit our website (www.qlight.com).
Mounting Accessories (Sold Separately)
• Please refer to the dimensions below for installation of mounting brackets
Ø22
PCD60~70
PCD50
PCD85
Ø10 CABLE ENTRY
360°/ 3-
Ø5.5 HOLES
6-Ø5.5 HOLES
4-Ø5.5 HOLES
26.511.5
115
70
90
65
Ø22
PCD60~70
PCD50
PCD85
Ø10 CABLE ENTRY
360°/ 3-
Ø5.5 HOLES
6-Ø5.5 HOLES
4-Ø5.5 HOLES
26.511.5
117
70
94
69

Qlight Co., Ltd. www.qlight.com | [email protected]
Head O󰀩ce | Suite #1510, STX-V Tower, 128 Gasan digital 1-ro, Geumcheon-gu, Seoul, Korea
Tel. [phone](Toll free. [phone]) Fax. [phone]
Factory | 185-25, Mukbang-ro, Sangdong-myeon, Gimhae-si, Gyeongsangnamdo, Korea Tel. [phone](Toll free. [phone])
Qlight OverSEAs Sales Dept | 704 Nakdong-daero, Sasang-gu, Busan, Korea(Eomgung-Dong) Tel : [phone]
Qlight Public Relations & Marketing Team O󰀩ce | 704 Nakdong-daero, Sasang-gu, Busan, Korea(Eomgung-Dong) Tel. [phone]
Qlight USA, Inc. www.qlight.com www.qlightusa.com | [email protected]
3003 North First Street, Suite #341, San Jose, CA 95134 USA Tel. [phone] Fax. [phone]
SHANGHAI Qlight Electronic Co., Ltd. www.qlight.com www.qlightcn.com | [email protected]
China Factory/ Shanghai Sales O󰀩ce | #19, Nanda Road, Baoshan Area, Shanghai, China Tel. +86 - 21 - 6651 - 7100 Fax. +86 - 21 - 6315 - 3929
China Factory Site 2 (Qidong) | #33, Haiyan Road, Qidong High-tech Industrial Development Zone, Qidong, Jiangsu Province, China
Tel +86 - 513 - 8384 - 9999 Fax +86 - 513 - 8384 - 9910
Product Operation Inquiry / Customer Support [phone]
You can expect prompt service if you have exact information such as model name, symptom, telephone number and address.
※ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Head office : Suite #1510, STX-V Tower, 128 Gasan digital 1-ro, Geumcheon-gu, Seoul, Korea (Postal Code : 08507)
Factory : 185-25, Mukbang-Ro, Sangdong-Myeon, Gimhae-Si, Gyeongsangnam-Do, Korea (Postal Code : 50805)
For your safety
Specication and dimensions listed in this catalogue subject to change without notice for product quality improvement.
The newest product information is available on our website.(www.qlight.com)
Please read the instruction manual attached to the product carefully before installation and use.
www.qlight.com
EN - S100R - 2106A