quiko Titano QK-T4000 User manual

Quiko®è un marchio Borinato F.lli Snc
E-mail: [email protected] Web: www.quiko.biz
Sede legale e stabilimento 1: Via Chiesa, 59 - 36040 San Germano D.B. (VI) - Italia
Tel: [phone] Fax: [phone]
Stabilimento 2: Via Seccalegno, 19 - 36040 Sossano (VI) - Italia
Tel: [phone] Fax: [phone]
TITANO
230/400V SLIDING GATE OPENER
USE AND MAINTENANCE MANUAL
E
N
G
L
I
S
H

TECHNICAL FEATURES
PRE-INSTALLATION CONTROL
Before installing the automation, you must check that:
- The wheels of the gate are attached to make the gate stable and must be in good condition;
- The entire length of the fixed runway must be free of obstacles, straight and clean and have control levers
at the ends;
- The upper guide, parallel to the rail and lubricated, must allow for a clearance of about 1 mm from the door
Borinato F.lli Snc is liable only for products it manufactures and commercializes. Once automated, the gate
becomes a machine and is therefore subjected to the rules of the “ Machinery Directive”. It is on the installer to
verify its security. WARNING: Borinato F.lli Snc is not liable for any damages to people, animals or things due to
unauthorised modifications, alterations or betterments on its products by third parties.
QK-T4000
QK-T6000
VOLTAGE SUPPLY (VAC)
230/400 Three -phase
POWER ABSORBED (W)
1100
1500
CURRENT ABSORBED (A)
4,5/2,6
6/3,5
OPERATING TEMPERATURE C°
-30/+70
GATE SPEED m/min
10
PROTECTION LEVEL IP
44
WORKING CYCLE %
60
GEARMOTOR WEIGHT kg
58
66
SPEED rpm
1400
REDUCTION RATIO
1/30
MAX. GATE WEIGHT kg
4000
6000

MATERIALS FOR INSTALLATION
Fig. 1
1. Gear-motor
2. Counterplate
3. M6 iron rack 30x30mm
4. Limit switch cammes
POSITIONING OF THE COUNTERPLATE
Fig. 2
2
3
4
1
4

INSTALLATION OF THE GEARMOTOR
Fig. 3
Open the removable cover of the gearmotor. Loosen the four screws and remove the case. Remove the nuts
used to fasten the anchoring brackets. Position the gearmotor onto the counterplate.
The gearmotor has to be adjusted:
- Horizontally: along the gearmotor base slot (approx. 20 mm).
- Vertically (if necessary): by means of the 4 level nuts and by inserting the spacers.
INSTALLING THE RACK
Fig. 4
The rack should preferably be welded to a 40x40 mm channel and then fastened to the gate with M10 bolts and nuts.
Release the gearmotor and set the gate in the open position. Place the rack on pinion and move the gate manually to
secure the rack along its full length. Once the rack has been secured, vertically adjust the geared motor so as to have a
gap of 2 to 3 mm between the pinion and the rack with screws. Firmly secure the gearmotor with the nuts. Slightly
lubricate the rack and pinion after assembly. Manually check that the gate slides evenly.

Fig. 5
POSITIONING THE LIMIT SWITCH CAMMES
Fig. 6
Open the gate manually and fasten the limit switch cammes (2) (3) onto the rack.

USE OF MANUAL UNLOCKING
Fig.7
RELEASE INSTRUCTIONS
In case of fault or power failure, open the removable door and unlock the pinion gear by turning the pinion
gear pin counter clockwise by means of the provided tool. This allows moving the gate manually. Attention:
perform locking and lock release operations with motor cut off.
LOCK INSTRUCTIONS
To lock the geared motor, rotate the pinion clockwise, strongly tighten, and re-close the removable door.
ADJUSTING THE CLUTCH
Fig. 8
Adjust the clutch as per fig.8.
IF THE GEARMOTOR IS PROVIDED WITH THE QK-CE220RLINV CONTROL BOARD THE CLUTCH
CAN BE DISACTIVATED BY TIGHTENING THE BOLT COMPLETELY

TYPICAL INSTALLATION
Fig. 9
MAIN COMPONENTS
1 - GEAR MOTOR
2 - CLOSING LIMIT SWITCH CAMME
3 - OPENING LIMIT SWITCH CAMME
4 - PHOTOCELL
5 - KEY SELECTOR
6 - PHOTOCELL ON POSTS
7 - PHOTOCELL POST
8 - FLASHING LAMP
9 - AERIAL
For all electrical connections see the Control Board INSTALLATION
MANUAL

DECLARATION OF COMPLIANCE
(in accordance with the European Regulation UE89/392 Appendix IIA)
Manufacturer: Borinato F.lli Snc
hereby declares, under his liability, that the products:
QK-T4000 and QK-T6000 gearmotors
are in compliance with the essential safety requirements of the regulations:
Regulation 89/392CE on Machinery and its subsequent amendments;
EMC Regulation 89/336/CE (Legislative Decree 615/96);
BT Regulation 73/23/CE e 93/68/CE (Legislative Decree 626/96);
CE Machinery Directive 98/37 and directive 93/68/CE-72/23/CE-92/31/CE;
and their amendments and modifications, and with the regulations set forth by the National
Legislative Body of the country in which the machinery is destined for use.
San Germano Dei Berici, 07/18/2005
The Legal Representative
Sede legale e stabilimento 1
Via Chiesa, 59
36040 San Germano Dei Berici (VI)
Italia
Stabilimento 2
Via Seccalegno, 19
36040 Sossano (VI)
Italia

Il produttore si riserva di apportare modifiche al presente manuale senza preavviso
Stabilimento 2
Via Seccalegno, 19 - 36040 Sossano (VI) - Italia
Tel: [phone] Fax: [phone]
Quiko®è un marchio Borinato F.lli Snc
E-mail: [email protected] Web: www.quiko.biz
Sede legale e stabilimento 1
Via Chiesa, 59 - 36040 San Germano D.B. (VI) - Italia
Tel: [phone] Fax: [phone]