RADWAG PM C32 User guide

Start up Guide
• PM C32
Precision Balances
IMMB-09-01-09-20-EN

To view a complete User Manual go to the website or scan QR code:
radwag.com/en/manuals/3670

1. CONTENT
*The plug type may vary by country.
Models: PM C32 (max: 25-50 kg)
Models: PM C32 (max ≤ 15 kg)
Power adapter*
×1
Power adapter*
×1
Power adapter*
×1
Precision balance
×1
Precision balance
×1
Precision balance
with weighing pan
×1
Weighing pan
×1
Weighing pan
×1
2. UNPACKING
1 2 3
Models: PM (max: 10-50 kg)
Models: PM 60.1.C32 (max ≥ 60 kg)

3. RECOMMENDATIONS AND WARNINGS
Operate the device in a room where the temperature ranges between 10–40 °C
(50–104 °F) and where the relative humidity is below 80%. Temperature must
change slowly and gradually.
Using the anti-vibration table is recom-mended in order to enable the most stable
and repeatable measurement.
+10 oC
+50 oF
+104oF
+40 oC
Avoid air drafts and air movements
at the workstation.
Place the balance away from heat
sources. Avoid exposing the balance
to the sunlight.
Avoid exposing the balance to a mag-
netic field. Do not weigh magnetic
substances.
Not intended for usage within EX
zones. Not intended for weighing
explosive or flammable substances.
Make sure that the balance is placed
on an even surface.
Do not place the balance on an
unstable surface exposed to shocks
and vibrations.
1 2 3
Models: PM C32 (max ≥ 60 kg)
Keep the packaging should a warranty
claim or service be required.

4. ACTIVITIES TO BE DONE PRIOR TO OPERATION
4.2. Grounding spring check
Check whether the grounding
spring takes its intended
location.
Make sure that the grounding
spring juts slightly out of the
hole.
Grounding
foot
21
Models: PM C32 (max = 60 kg only)
Models: PM C32 (max: 10 - 50 kg only)
4.1. Remove transport lock
5. COMPONENTS ASSEMBLY
Models: PM C32 (max ≤ 15 kg)
1 2

6. PREPARING FOR WORK
6.1. Temperature stabilization
Place the device at the workstation, wait until
it reaches room temperature.
Prior to switching the device on,
let it reach room temperature
(estimated stabilisation time: 1-8 hours).
Connect the power adapter
to DC connector.
Connect the power
adapter to the mains.
1 2 3
1
up to 1- 8 h
Models: PM C32 (max: 25-50 kg)
Models: PM C32 (max = 60 kg)
1
1
2
2

6.2. Balance levelling
Your balance is ready to use!
To switch the device on, press ON / OFF key.
6.3. Switching the balance on
Models: PM C32 (max: 10 - 50 kg)
Models: PM C32 (max = 60 kg)
To level the balance, turn its
feet and keep turning the feet
until an air bubble takes the
central position.
To level the balance, turn its
feet and keep turning the feet
until an air bubble takes the
central position.

7. PANEL AND SCREEN
7.1. Panel keys
7.2. Home screen
Proximity sensor
Switching on / off
Main menu
Log in
Cancel
Text / Numeric
keyboard mode
Back / delete
Zeroing
Taring
Weighing unit
Confirm
Working mode
ENTER / PRINT
Text / Numeric keyboard
with navigation keys
Proximity sensor
Editable quick
access toolbar
Configurable additional
information field
Weighing result
window
Status bar
Working mode Communication status
Adjustment Print footerPrint header Select product Databases

Press the key under the icon to start
the adjustment.
Wait for the adjustment completion.
8. BASIC OPERATIONS
8.1. Adjustment
1 2
8.3. Taring
8.2. Zeroing
1
1
2
2
With loaded weighing pan: upon stabilization
of the weighing result, press key.
Make sure that the weighing pan is empty
and press key.
The balance has been tared.
The balance has been zeroed.
0.68
0.68
0.21
0.21
0.21 0.21

9. SETTINGS
9.1. Administrator’s logging in
1 2
Some balance settings are accessible for Administrator exclusively.
Prior balance parameters setup, log in as the Administrator.
Press key To enter ‘’User’’ menu. Users list is displayed. Using keys, select
“Admin” option and press key to confirm.
Log out
2
Admin
Operators
Admin
8.4. Working modes selection
8.5. Units selection
Weighing
Dosing
Checkweighing
Formulations
Percent weighing
Statistics
Parts counting
Animal weighing
Solids density
Liquids density
Peak hold
•Gram [g]
•Miligram [mg]
•Carat [c]
•Pound [lb]
•Ounce [oz]
•Troy ounce [ozt]
•Pennyweight [dwt]
•Hong Kong Tael [tlh]
•Singapore tael [tls]
•Taiwanese tael [tlt]
•Chinese tael [tlc]
•Momme [m]
•Grain [gr]
•Tical [ti]
•Newton [N]
•Baht [baht]
•Tola [tola]
•Mesghal [msg]
•User unit 1
•User unit 2
Using key enter working modes menu. Using keys select working
mode and press key to confirm.
Press the key to change the weight unit.
The balance enables selecting the
following weighing units:

Users
Admin
Name New
New
Password
Permissions
******
User
Code
3 4
Using numeric keyboard enter “1111” password
and press key to confirm.
You have logged as the administrator.
1111
Operators
9.2. User settings
1 2
Prior balance users setup, log in as Administrator (point 9.1.).
Databases
Products 0
Packaging 0
Customers 0
Users 1
Press the key under the icon to enter
databases.
Using keys, go to “Users” and press
key to confirm.
3 4
Press the key under the icon to add
a new user.
Select “Name” parameter and press key
to confirm.

9.3. Proximity sensors setup
Prior balance proximity sensors setup, log in as Administrator (point 9.1.).
You can assign the proximity sensors with different functions for each working mode (the sensors will trigger
different operation for each working mode). The diagram presents sensors setup for the “Weighing” mode.
1 2
Press key. Using keys, go to “Working Modes” and
press key to confirm.
Parameters
Reports
Communication
Data bases
Working modes
Using keyboard enter user name and
press key to confirm.
5 6
User name has been entered.
New
Name John Smith
Password
Permissions
******
User
Code
7
Code:
Enter user ID
Password:
Enter user password
Access levels:
Set respective access level
(user, advanced, admin)
Following the above procedure, set remaining parameters:

Following the above procedure you can configure sensors for other working modes.
4
6
5
Using keys select “Proximity sensors”,
and press key to confirm.
Using keys select “Weighing” mode,
and press key to confirm.
Using keys select the appropriate sensor
(right or left), and press key to confirm.
Using keys set function that is to be
assigned to a selected sensor, and press
key to confirm.
Weighing
Readout
Autotare
Print mode When stable
Proximity sensors
Right sensor
Accept / Print
Print header
Print footer
Zeroing
Left sensor None
Right sensor
3
Working modes
Availability
Parts counting
Checkweighing
Weighing

10. PERIPHERAL DEVICES CONNECTORS
Wi-Fi®
Wi-Fi ®is a registered trademark of Wi-Fi ®Alliance.
Computer
Computer
Computer
Computer
Printer
Printer
Printer
Printer
Keyboard
Barcode
scanner
Barcode
scanner
Power adapter
Additional
display

11. DEVICE CLEANING
Prior to cleaning, it is necessary to
disconnect th e balance from the
mains.
Use soft cloths made of microfiber,
natural fiber or man-made fiber. Avoid
using abrasive cloths or cloths that
might scratch the surface.
Apply the cleanser onto the cloth first.
Avoid applying the cleanser directly
onto the device.
11.1. General recomendations
Do not use aggressive cleaning
agents (e.g. solvents, chlorine
preparations, corrosive chemicals,
bleach).
• GLASS PANES AND COMPONENTS can be cleaned using window cleaner.
• WEIGHING PANS AND STAINLESS STEEL OR ALUMINIUM COMPONENTS can be cleaned using a cloth slightly
soaked in a solution of water and gentle cleanser (e.g. soap or dishwashing liquid).
• OPERATION PANEL AND HOUSING can be cleaned using a cloth slightly soaked in a solution of water and gentle
cleanser (e.g. soap or dishwashing liquid).
• Dry sample leftovers can be removed using either brush or handheld vacuum cleaner.
•Clean components can be dried using soft cloth or dust-free paper towel, with this the remaining moist will be absorbed.
• Install all the components providing they are completely dry.
Neither use substances of sharp
structure nor intended for
scrubbing.
Make sure that neither dust nor
liquid gets inside the weighing
system (device inside).
11.2. Cleaning instructions

www.radwag.com