RAK RAK566 User manual

How to config network parameters and Pair the Module
This document is only using for Flylink HD .
Flylink HD : RAK566(TX) and RA554(RX).
RAK5610 is same with RAK554 including firmware and Hardware.
1 RAK554 PIN Definition
2 RAK554 Dip switch definition
There are 6 group Dial-up in the module . ON direction is showing low-level ,marked as 0.
When The Dial-up is on the opposite direcetion ,that is showing high-level,marked as 1 .
The dial-up flag order is 1-6,marked as sw1-6.
The function definition is followed ：
Sw6
Sw5
Band
Channel
Band
1
1
4
149
5745
1
0
1
48
5240
0
1
1
36
5180
0
0
4
165
5825
The default band is Band4. That is to say channel 149.
Sw1 is using for WPS function . If you want to use this function , you need do the following
steps.
Step1 : Whatever the SW1 level , set SW1 into low-level more than 1 second .
Step2 : Then Set SW1 into high-level .
Step3 : The Wifi light will blink.that is showing you have step into the WPS mode.
After power on the module,please scan the AP：FS_5G_AP_xxxxxx or Flylink_xxxxxx（please
make sure your smartphone supporting 5G SSID）. X means MAC address.

3 How to change SSID and PSK
RAK553 will work as OPEN network .if you have to change the SSID and PSK .please following
the steps strictly. Note: Once you change the network parameters, you have to make a new
connection with Transmitter. Please reference the PART 5.
Step 1 : Power on RAK553.
Step 2: Waiting for the Blue LED turn on and that means the restart completed .
Step 3: Scan and connect the AP with your 5G WIFI device ,such as phone,pad ,or PC .
Step 4: Open broswer and input the following HTTP command in the address bar and Enter .
you need to input the user and password which both are admin. If you get the “value”:”0”,
that means the configuration succeed.
HTTP Command: Encryption :
192.168.100.1/param.cgi?action=update&group=wifi&ap_ssid=RAK_5G_AP_XXXXX%20%23=BR
ING&ap_auth_mode=WPA2PSK&ap_encrypt_type=AES&ap_auth_key=RAK12345
Function:
Change the network to WAP2 encryption and a new SSID .
Key point(Red words) :
IP address : 192.168.100.1. Must be 192.168.100.1!
SSID : RAK_5G_AP_XXXXX. Change to what you want ,such as SMD_5G_AP_CC566A . we can
only support the following chars. but we suggest you’d sue the letters and numbers .
./abcdefghijklmnopqrstuvwxyzABCDEFGHIJKLMNOPQRSTUVWXYZ_-+=&1234567890@[]?%#
PSK : RAK12345. Change to what you want ,such as 1234567890 . the length must be in the
range from 8 char to 32 char. we can only support the following chars.
./abcdefghijklmnopqrstuvwxyzABCDEFGHIJKLMNOPQRSTUVWXYZ_-+=&1234567890@[]?%#
Note: please don’t change any other words !
HTTP Command:Open :
192.168.100.1/param.cgi?action=update&group=wifi&ap_ssid=RAK_5G_AP_XXXXX%20%23=BR
ING&ap_auth_mode=OPEN&ap_encrypt_type=NONE
Function:
Change the network to OPEN mode and a new SSID .
Key point(Red words) :
IP address : 192.168.100.1. Must be 192.168.100.1!
SSID : RAK_5G_AP_XXXXX. Change to what you want ,such as SMD_5G_AP_CC566A . we can
only support the following chars.but we suggest you’d sue the letters and numbers .
./abcdefghijklmnopqrstuvwxyzABCDEFGHIJKLMNOPQRSTUVWXYZ_-+=&1234567890@[]?%#
Note: please don’t change any other words !
4 Example
Change the network to OPEN mode and a new SSID: SMD_5G_AP_CC566A .
Command:

192.168.100.1/param.cgi?action=update&group=wifi&ap_ssid=SMD_5G_AP_CC566A%20%23=B
RING&ap_auth_mode=OPEN&ap_encrypt_type=NONE
Input the command in Broswer and input the user and password with admin.
HTTP Successful Return:
5Make new Pair
Transmitter（STA）: RAK566.
Step1 : Power on RAK566 waiting the board blink or lighting more than 10 seconds .
Step2 : Power on RAK554(RX) and waiting for blue LED turn on . Toggle Receiver’s DIP
switch PIN1 to Low-Level more than 1 second and then Toggle to High-Level .The blue LED will be
quick flashing. The Receiver have run into WPS Pair mode .
Step3 : Press the button in the red circle 3 seconds and leave . the blue LED will be
quick flashing. The Receiver have run into WPS Pair mode . If not ,please try again .
Step4 : Waiting for the Transmitter blue LED turn on more then 10 seconds. That means the
configuration have completed .
6 Enclosure
Android APP: https://www.pgyer.com/camsight
IOS APP : Search in APPLE STORE with camsight sport and install.
Document Center：

www.rakwireless.com/en/download
wiki.rakwireless.com/doku.php
Support Center：
supporten.rakwireless.com/
Website：
www.rakwireless.com
APP SDK Source code(rakvideo)：
www.github.com/rakwireless