Razor Black Label R Tec User manual

Black Label R Tec™ Scooter
OWNER’S MANUAL
Read and understand this entire manual before allowing
child to use this product! For assistance contact Razor.
DO NOT RETURN TO STORE.
NOTE: Manual illustrations are for demonstration purposes only.
Illustrations may not reflect exact appearance of actual product.
Specifications subject to change without notice.
Please have your product along with the 22 character product I.D. code with you
before contacting Razor for warranty assistance and/or replacement parts.
Product I.D. Code: _____________ - ____________ - ____________

1
CONTENTS
SAFETY WARNINGS
AN IMPORTANT MESSAGE TO PARENTS: This manual contains
important information. For your child’s safety, it is your responsibility to
review this information with your child and make sure that your child
understands all warnings, cautions, instructions and safety topics. All
children and preteens should ride with adult guidance at all times. Razor USA
recommends that you periodically review and reinforce the information in this
manual with younger riders, and that you are required to inspect and maintain
your child’s scooter to ensure their safety.
GENERAL WARNING: Scooter riding can be a hazardous activity.
Scooters can and are intended to move, and it is therefore possible to get into
dangerous situations and/or lose control and/or fall. If such things occur you
can be seriously injured or die. LIKE ANY OTHER MOVING PRODUCT, USING
A SCOOTER CAN BE A DANGEROUS ACTIVITY AND MAY RESULT IN INJURY
OR DEATH EVEN WHEN USED WITH PROPER SAFETY PRECAUTIONS. USE AT
YOUR OWN RISK AND USE COMMON SENSE.
• Always wear safety equipment, such as helmet, knee pads and elbow
pads. Always wear a helmet when riding your scooter and keep the
chinstrap securely buckled.
• Always wear closed toe shoes.
• Ride on smooth, paved surfaces away from motor vehicles.
• Avoid sharp bumps, drainage grates, and sudden surface changes. Scooter
may suddenly stop.
• Avoid streets and surfaces with water, sand, gravel, dirt, leaves, and other
debris. Wet weather impairs traction, braking, and visibility.
• Do not ride at night.
• Brake will get hot from continuous use. Do not touch after braking.
• Avoid excessive speed associated with downhill rides.
• Adults must assist children in the initial assembly and/or adjustment
procedures to adjust handlebar scooter.
• Obey all local traffic and scootering laws and regulations.
• Watch out for pedestrians.
• Do not exceed 220 lb (100 kg) total weight on the Black Label R Tec.
• A parent’s decision to allow his or her child to ride this product should be
based on the child’s maturity, skill and ability to follow rules.
• Do not allow children under age six (6) to use the Black Labe R Tec scooter.
Black Label R Tec scooters are for children ages six (6) and above. All
children and preteens should ride with adult guidance at all times.
• Rider weight does not necessarily mean a child’s size is appropriate to fit or
maintain control of the scooter.
ACCEPTABLE RIDING PRACTICES AND CONDITIONS
Direct parental supervision is required. Scooters are meant to be used only
in controlled environments free of potential traffic hazards and not on public
streets. Do not allow your child to ride a scooter in any areas where vehicle
traffic is present. Child must maintain a hold on the handlebars at all times.
Never allow more than one child at a time to ride a scooter. Never use near
steps, sloped driveways, hills, roadways, alleys or swimming pool areas.
Adults must not allow children to assist in assembling the scooter.
Do not ride a scooter in wet weather. Scooters are intended for use on solid,
flat, clean and dry surfaces, such as pavement or level ground without loose
debris, such as rocks or gravel. Wet, slick or uneven and rough surfaces may
impair traction and contribute to possible accidents. Do not ride a scooter in
mud, ice, puddles or water. Avoid excessive speeds that can be associated
with downhill rides. Never risk damaging surfaces, such as carpet or flooring,
by use of a scooter indoors. Do not ride at night or when visibility is impaired.
PROPER RIDING ATTIRE
Always ensure rider is wearing proper protective equipment, such as an
approved safety helmet. A helmet may be legally required by local law or
regulation in your area. A rider should always wear shoes and keep shoelaces
tied and out of the way of the wheels. Never ride barefooted or in sandals.
Knee pads and elbow pads are recommended.
WARNING: ALWAYS INSPECT SCOOTER PRIOR TO RIDING. Properly
inspecting and maintaining your scooter can reduce the risk of injury. Always
inspect your scooter before riding and regularly maintain it. Check and secure
all fasteners before every ride. Replace worn or broken parts immediately.
WARNING: CHECK LOCAL LAWS REGARDING SCOOTER USE.
Check local laws and regulations to see where and how you may use
your Razor scooter legally. In many states and local areas scooter riders
are required BY LAW to wear a helmet. Check local laws and regulations
regarding laws governing helmet use and scooter operation in your area.
FAILURE TO USE COMMON SENSE AND HEED THE ABOVE
WARNINGS FURTHER INCREASES RISK OF SERIOUS INJURY. USE
AT YOUR OWN RISK AND WITH APPROPRIATE AND SERIOUS
ATTENTION TO SAFE OPERATION. USE CAUTION.
Safety Warnings .............................................................................................. 1
Before You Begin.............................................................................................. 2
Assembly and Set-up....................................................................................... 3
Pre-Ride Checklist and Usage.......................................................................... 4
Repair and Maintenance.................................................................................. 5
Warranty and Contact Information.................................................................. 6

2
Need Help? Visit our web site for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service
contact information is listed at the back of this manual.
BEFOREYOU BEGIN
Remove contents from box. Inspect the contents of the box for scratches and/or dents that may have occurred during
shipping. Because your scooter was partially assembled and packed at the factory, there should not be any problems,
even if the box has a few scars or dents.
WARNING:
DO NOT USE NON-RAZOR
PRODUCTS WITH YOUR SCOOTER.
Razor scooters have been built to
certain Razor design specifications.
The original equipment supplied at
the time of sale was selected on
the basis of its compatibility with
the frame, fork and all other parts.
Certain aftermarket products may
not be compatible and will void
the warranty.
Required Tools
5 mm
Allen wrench
Product ID Locations:
1. Side of deck plate
2. Box - side of UPC (not shown)
Box Contents:
• Scooter
• Allen wrench
• Owner’s manual
Quick-release lever
Extension tube
Brake
T-bar
Collar clamp

3
Need Help? Visit our web site for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service
contact information is listed at the back of this manual.
ASSEMBLY AND SET-UP
Note: The tension of the quick-
release lever can be adjusted by
manually tightening or loosening
the Allen bolt. Be careful not to
over-tighten. You should always
be able to open and close the
quick-release lever by hand and the
T-bar should slide freely when the
quick-release is open unless T-bar
is fully extended.
4To adjust the height of the
handlebars, open the quick-release
lever and slide the T-bar to the
desired position. Resecure the
quick release lever to lock into
place. When the T-bar is raised to
the maximum height, depress the
push button located directly below
the quick release lever to unlock
the T-bar.
1Open the quick-release lever
and fully extend the T-bar to the
maximum height.
Attaching and Adjusting the Handlebars
Required Tool: 5 mm Allen wrench
WARNING: Failure to
properly secure the quick-release
lever may cause the T-bar to
telescope up or down while riding
and may cause you to lose control
and fall.
3With the front wheel pointed
straight ahead and the
handlebars square to the front
wheel and the Razor logo facing
the front, tighten the clamp as
shown. Tighten securely.
2Loosen the collar clamp. Insert
T-bar into the fork until it bottoms
out on the headset locknut.
Note: If necessary, carefully twist
the T-bar while pushing downward.
WARNING: Failure to
properly install and tighten the
collar clamp may cause the rider
to lose control and fall. If you are
having difficulty understanding
these instructions, please
contact Razor Customer Service
for assistance.

4
Need Help? Visit our web site for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service
contact information is listed at the back of this manual.
PRE-RIDE CHECKLIST
How to Ride
Place one foot on the baseboard, push forward with the other foot. Steer with both hands on the handlebars.
For enhanced cornering, lean slightly into the direction of the turn. For controlled stops, apply the brake by stepping
on the rear brake. Razor recommends that you practice applying the brake at various speeds and in an open area
free from obstructions before riding your scooter around others.
Loose Parts
Check and secure all fasteners before every ride. Make sure the
collar clamp and quick release lever are locked properly in place
before riding.
Replacement Parts
Replace worn or broken parts immediately.
Call 1-866-467-2967 for parts or visit www.razor.com.
Safety Gear
Always wear proper protective equipment, such as an approved
safety helmet, elbow pads and kneepads. Always wear shoes
(lace-up with rubber soles) and keep shoelaces tied and out of
the way of the wheels. Never ride barefooted or in sandals.
Be Careful!
You will see people on TV and maybe even people you know doing
tricks and stunts. These are people who have been practicing on
scooters for a very long time. Don’t try something until you are
ready. Avoid steep inclines and don’t ride too fast — you can lose
control and fall. Skateboard parks are not designed for scooters.
Never ride in traffic or on the street and watch your surroundings
for pedestrians, bikers, boarders and skaters.
Maintain a hold on the handlebars at all times.
USAGE

5
Need Help? Visit our web site for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service
contact information is listed at the back of this manual.
REPAIR AND MAINTENANCE
Collar Clamp
Using a 5 mm Allen wrench, check that the collar clamp bolt are tightened securely. This item is tightened and quality
inspected at the factory, but there is a slight chance that the effects of shipping or handling may have caused the bolt
to loosen.
Wheels and Bearings
Under normal circumstances and conditions, Razor wheels and wheel bearings are maintenance free. Nonetheless, it
is the responsibility of the owner or guardian to periodically inspect the wheels for wear and tear, the axle for proper
tightness, bearings for side-to-side play, and loose parts. When a wheel or wheel bearing develops play, this is an
indication of excess wear, and replacement is necessary. Replace immediately with only genuine Razor wheels. Worn
wheels/bearings are considered normal wear-and-tear and are not covered by the Razor Warranty. Wheels other than
genuine Razor wheels may not be compatible with your Razor scooter. The use of anything other than genuine Razor
replacement parts may affect your safety and will void your warranty.
Cleaning Your Scooter
Wipe with a damp cloth to remove dirt and dust. Do not use industrial cleaners or solvents as they may damage the
surfaces. Do not use alcohol, alcohol-based or ammonia-based cleaners as they may damage or dissolve the plastic
components or soften the decals or decal adhesive.
WARNING:
Wheelies and other stunt-type
riding reduces your ability to
maneuver and control your scooter.
WARNING:
Failure to properly install and/
or tighten the collar clamp may
cause the rider to lose control and
fall. If you are having difficulty
understanding these instructions,
please contact Razor Customer
Service for assistance.

6
WARRANTY
Razor Limited Warranty
The manufacturer warranties this product to be free of manufacturing defects
for a period of 6 months from date of purchase. This Limited Warranty does
not cover normal wear and tear, or any damage, failure or loss caused by
improper assembly, maintenance, or storage.
This Limited Warranty will be void if the product is ever:
• used in a manner other than for recreation;
• modified in any way;
• rented.
The manufacturer is not liable for incidental or consequential loss or damage
due directly or indirectly to the use of this product.
Razor does not offer an extended warranty. If you have purchased an
extended warranty, it must be honored by the store at which it was
purchased.
For your records, save your original sales receipt with this manual.
__________________________________________
Printed in China for:
Razor USA LLC
PO Box 3610
Cerritos, CA 90703
Copyright © 2003-2014 Razor USA, LLC. All rights reserved. RAZOR and the Razor logo
design are among the registered trademarks of Razor USA LLC in the United States and/or
select foreign countries. R Tec™ is a trademark of Razor USA LLC. US_141023
CUSTOMER SERVICE CONTACT INFORMATION
UNITED STATES
Razor USA LLC
P.O. Box 3610
Cerritos, CA 90703
USA
[phone]
Monday - Friday
8:00 AM - 5:00 PM Pacific Time
DISTRIBUTED IN THE UK BY:
Re:creation Limited
2 Meadows Business Park
Station Approach, Blackwater
Camberley, Surrey GU17 9AB
United Kingdom
[phone] Tel
[phone] Fax
[email protected]
ASIA
Razor USA (Asia)
P.O. Box 3610
Cerritos, CA 90703
USA
[phone]
[e-mail]
EUROPE
Razor USA (Europe)
Handelsweg 2
2742 RD Waddinxveen
Netherlands
[phone]
DISTRIBUTED IN AUSTRALIA BY:
Funtastic Limited
Level 2, Tower 2, Chadstone Place
1341 Dandenong Road
Chadstone VIC 3148
Australia
[phone]
Need Help? Visit our web site for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service
contact information is listed below: