Razor E100 series User manual

E100/E125 (V16+), E150 (V6+),
E175 (V19+), ESPARK ELECTRIC SCOOTER
BATTERY INSTALLATION INSTRUCTIONS
WARNING
Do not use non-Razor products with your Razor electric
scooter. The scooter has been built to certain Razor
design specifications.Certain aftermarket parts may or
may not be compatible.
As with all consumer electronics, use of compatible
batteries and chargers is strongly recommended. Failure
to do so may pose a fire hazard.
Examine the battery, charger and their connectors for
excessive wear or damage each time you charge the
battery. If damage or excessive wear is detected, do not
use the charger or the vehicle until you have replaced
the worn or damaged part.
Battery connectors may contain lead and lead
compounds. Wash your hands after handling.
Need Help? Visit our website at www.razor.com or call toll-free at 866-467-2967 Monday - Friday 8:00am - 5:00pm Pacific Time.
1
Tools Required: (Not included)
A. Phillips head screwdriver
B. 4mm Allen wrench
C. 8mm open wrench
CAUTION: To avoid potential shock or other injury, turn power switch OFF and discon-
nect charger before removing or installing the batteries. Failure to follow these steps in the
correct order may cause irreparable damage.
Figure 1 Figure 2
Step 1
Using a Phillips head screwdriver, remove the four
screws in the front of the deck. Using a Phillips
head screwdriver and 8mm open wrench, remove
the two screws and locknuts in the back of the
deck. Using a 4mm Allen wrench remove the two
hex bolts. Remove deck plate.
Note: If you are having difficulty removing the
screws, use pliers to twist the screw out from the
bottom.
Using a Phillips head screwdriver, remove the
screws on the battery bracket and remove
bracket.
Step 2
Phillips head screwdriver
4mm Allen wrench
Phillips head screwdriver on top,
8mm open wrench on bottom

Need Help? Visit our website at www.razor.com or call toll-free at 866-467-2967 Monday - Friday 8:00am - 5:00pm Pacific Time.
2
Figure 3 Figure 4
Locate the white plastic connector on the battery.
Cut the zip tie and discard it. Disconnect the white
plastic connectors attached to the battery and
control module by depressing the tab.
Follow the single black and red wires on the bat-
tery to the reset button and gently unplug both
wires from the reset button.
Step 3 Step 4
Figure 5 Figure 6
Carefully lift the batteries out of the battery tray,
one battery at a time. See page 3 for battery care
and disposal information.
Place new batteries in battery tray in the position
shown below.
Step 5 Step 6
Step 7
Reverse steps:
1. Reconnect the battery connector to the connector on the control module.
2. Plug the red and black wires on the battery into the reset button (in no particular order)
3. Reattach battery bracket and deck plate.
ATTENTION: Charge unit at least 18 hours before riding.

Need Help? Visit our website at www.razor.com or call toll-free at 866-467-2967 Monday - Friday 8:00am - 5:00pm Pacific Time.
3
v1 - 12/09
Battery Care
Battery Disposal
Battery Care:
Charge a new battery for at least 18 hours before you use it in
your product for the first time. Never charge the battery longer
than 30 hours. Overheating or undercharging the battery may
shorten battery life and decrease product run time.
After the first charge, recharge the battery for at least 12 hours
after each use. Charge the battery after each use, regardless
of how long the product was used.
Do not allow the battery to run down completely before
charging.
Charge the battery at least once per month, even if the
product has not been used.
Charge the battery before storing the product. Leaving the
battery in a discharged condition can result in a battery that
will no longer take a charge.
Do not store in freezing or below freezing temperatures
Charger:
The charger supplied with the scooter should be regularly
examined for damage to the cord, plug, enclosure and other
parts and in the event of such damage, the scooter must not
be charged until the carger has been repaired or replaced.
Your Razor product uses sealed lead-acid batteries which must be recycled or disposed of in an environmentally sound manner.
Do not dispose of a lead-acid battery in a fire. The battery may explode or leak. Do not dispose of a lead-acid battery in your
regular household trash. The incineration, land filling or mixing of sealed lead acid batteries with household trash is prohibited
by law in most areas. Return exhausted batteries to a federal or state approved lead-acid battery recycler or a local seller of
automotive batteries. If you live in Florida or Minnesota, it is prohibited by law to throw away lead-acid batteries in the municipal
waste stream.
CONTAINS SEALED LEAD-ACID BATTERY. BATTERY MUST BE RECYCLED.
WARNING: If a battery leak develops, avoid contact with the leaking acid and place the damaged battery in a plastic
bag. Refer to the disposal instructions below. If acid comes into contact with skin or eyes, flush with cool water for at least 15
minutes and contact a physician.