ResMed AirCurve 10 CS PaceWave User manual

User guide
User guide
English | Deutsch | Français | Italiano | Nederlands

English 1
ENGLISH
Welcome
The AirCurve™10 CS PaceWave™is a positive airway pressure device that belongs to the adaptive
servo-ventilator category.
WARNING
•Read this entire guide before using the device.
•Use the device according to the intended use provided in this guide.
•The advice provided by your prescribing doctor should be followed ahead of the
information provided in this guide.
•This device is not suitable for ventilator-dependent patients.
AirCurve 10 CS PaceWave indications for use
The AirCurve 10 CS PaceWave is indicated to stabilise the ventilation of adult patients exhibiting
central sleep apnoea (CSA), mixed sleep apnoea and periodic breathing, with or without obstructive
sleep apnoea. It is intended for home and hospital use.
The humidifier is intended for single patient use in the home environment and re-use in a
hospital/institutional environment.
Clinical benefits
The clinical benefit of CPAP therapy is a reduction in apnoeas, hypopnoeas and sleepiness, as well
as improved quality of life. The clinical benefit of ASV therapy for the treatment of CSA is a
reduction in apnoeas and hypopnoeas.
The clinical benefit of humidification is the reduction of positive airway pressure related side effects.
Contraindications
ASV therapy is contraindicated in patients with chronic, symptomatic heart failure (NYHA 2-4) with
reduced left ventricular ejection fraction (LVEF ≤ 45%) and moderate to severe predominant central
sleep apnoea.
Positive airway pressure therapy may be contraindicated in some patients with the following
pre-existing conditions:
•severe bullous lung disease
•pneumothorax or pneumomediastinum
•pathologically low blood pressure, particularly if associated with intravascular volume depletion
•dehydration
•cerebrospinal fluid leak, recent cranial surgery, or trauma.

2
Adverse effects
You should report unusual chest pain, severe headache, or increased breathlessness to your
prescribing physician. An acute upper respiratory tract infection may require temporary
discontinuation of treatment.
The following side effects may arise during the course of therapy with the device:
•drying of the nose, mouth, or throat
•nosebleed
•bloating
•ear or sinus discomfort
•eye irritation
•skin rashes.
At a glance
The AirCurve 10 includes the following:
•Device
•HumidAir™humidifier (if supplied)
•Air tubing
•Power supply unit
•Travel bag
•SD card (not available in all devices).
Contact your care provider for a range of accessories available for use with the device including:
•Air tubing (heated and non-heated): ClimateLineAir™, SlimLine™, ClimateLineAir Oxy, Standard
•Side cover for use without the humidifier
•Filter: Hypoallergenic filter, standard filter
•Air10™DC/DC converter (12V/24V)
•SD card reader
•Air10 oximeter adapter
•Air10 USB adapter
•Power Station II
•Air10 tubing elbow.

English 3
About your device
1
Air outlet
5
HumidAir humidifier
2
Air filter cover
6
Screen
3
Power inlet
7
Adapter cover
4
Serial number and device number
8
SD card cover
About the control panel
Start/Stop button
Press to start/stop therapy.
Press and hold for three seconds to enter power save
mode.
Dial
Turn to navigate the menu and press to select an option.
Turn to adjust a selected option and press to save your
change.
Home button Press to return to the Home screen.
Different icons may be displayed on the screen at different times including:
Ramp Time Wireless signal strength (green)
Humidity Wireless transfer not enabled (grey)
Humidifier warming No wireless connection
Humidifier cooling Airplane Mode

4
Setup
CAUTION
Do not overfill the humidifier as water may enter the device and air tubing.
1. Place the device on a stable level surface.
2. Plug the power connector into the rear of the device. Connect one end of the power cord into
the power supply unit and the other end into the power outlet.
3. Connect the air tubing firmly to the air outlet located on the rear of the device.
4. Open the humidifier and fill it with water up to the maximum water level mark.
Do not fill the humidifier with hot water.
5. Close the humidifier and insert it into the side of the device.
6. Connect the free end of the air tubing firmly onto the assembled mask.
See the mask user guide for detailed information.
Recommended masks are available on www.resmed.com.

English 5
Recommended water type (France only)
The following water types are recommended for use in the humidifier:
•Boiled tap water, cooled to room temperature
•Distilled water
•Bottled water (with a low mineral content).
Note: Do not use non-sterile demineralised water for domestic use.
Performing a functional check
1. With the device powered off:
•Check the condition of the device and accessories.
Inspect the device and all the provided accessories. If there are any visible defects, the
system should not be used.
•Check the air tubing setup.
Check the integrity of the air tubing. Connect the air tubing firmly to the air outlet and other
accessories if in use.
2. Turn the device on.
3. Check the HumidAir humidifier (if in use).
Press Start/Stop on the device. The Sleep Report screen will display at the bottom of the
screen if the humidifier is in use.
Starting therapy
1. Fit your mask.
See the mask guide for fitting instructions or use the Mask Fit function to check the mask fit and
seal.
2. Press Start/Stop or breathe normally if SmartStart™is enabled.
You will know that therapy is on when the Sleep Report screen is displayed.
The pressure bar shows the inspiratory and expiratory pressures in green.
The green bar will expand and contract as you breathe in and out.
The screen will go black automatically after a short period of time. You can press Home or the dial to
turn it back on. If power is interrupted during therapy, the device will automatically restart therapy
when power is restored.
The AirCurve 10 device has a light sensor that adjusts the screen brightness based on the light in
the room.
Stopping therapy
1. Remove your mask.
2. Press Start/Stop or if SmartStart is enabled, therapy will stop automatically after a few seconds.

6
The Sleep Report now gives you a summary of your therapy session.
Usage hours–Indicates the number of hours of therapy you received last
session.
Mask Seal–Indicates how well your mask sealed:
Good mask seal.
Needs adjusting, see Mask Fit.
Humidifier–Indicates if your humidifier is working properly:
Humidifier working.
Humidifier might be faulty, contact your care provider.
Total Used Hrs (Germany only)–Indicates the total number of hours you have used your device
since you first started using it.
If set by your care provider, you will also see:
Events per hour–Indicates the number of apnoeas and hypopnoeas experienced per hour.
More Info–Turn the dial to scroll down to view more detailed usage data.
Power save mode
Your AirCurve 10 device records your therapy data. In order to allow it to transmit the data to your
care provider, you should not unplug the device. However, you can put it into power save mode to
save electricity.
To enter power save mode:
•Press and hold Start/Stop for three seconds.
The screen goes black.
To exit power save mode:
•Press Start/Stop once.
The Home screen is displayed.
My Options
Your AirCurve 10 device has been set up for your needs by your care provider, but you may find you
want to make small adjustments to make your therapy more comfortable.
Highlight My Options and press the dial to see your
current settings. From here, you can personalise your
options.

English 7
Ramp Time
Designed to make the beginning of therapy more comfortable, Ramp Time is the period during
which the pressure increases from a low start pressure to the prescribed treatment pressure.
You can set your Ramp Time to Off or between 5 to 45 minutes.
To adjust Ramp Time:
1. In My Options, turn the dial to highlight Ramp
Time and then press the dial.
2. Turn the dial to adjust the ramp time to your
preferred setting and press the dial to save the
change.
Humidity Level
The humidifier moistens the air and is designed to make therapy more comfortable. If you are
getting a dry nose or mouth, turn up the humidity. If you are getting any moisture in your mask, turn
down the humidity.
You can set the Humidity Level to Off or between 1 and 8, where 1 is the lowest humidity setting
and 8 is the highest humidity setting.
To adjust the Humidity Level:
1. In My Options, turn the dial to highlight Humidity
Level and then press the dial.
2. Turn the dial to adjust the humidity level and press
the dial to save the change.
If you continue to get a dry nose or mouth, or moisture in your mask, consider using ClimateLineAir
heated air tubing. ClimateLineAir together with Climate Control delivers more comfortable therapy.
Mask Fit
Mask Fit is designed to help you assess and identify possible air leaks around your mask.
To check Mask Fit:
1. Fit the mask as described in the mask user guide.
2. In My Options, turn the dial to highlight Run Mask Fit and then press the
dial.
The device starts blowing air.
3. Adjust the mask, mask cushion and headgear until you get a Good result.
To stop Mask Fit, press the dial or Start/Stop. If you are unable to get a good mask seal, assess
whether you have the right mask size and/or type or talk to your care provider.

8
More options
There are some more options on your device which you can personalise.
Leak Alert* When Leak Alert is enabled, the device beeps if the mask leaks too much air or if you remove
the mask during therapy.
SmartStart* When SmartStart is enabled, therapy starts automatically when you breathe into your mask.
When you remove your mask, it stops automatically after few seconds.
*When enabled by your care provider.
Caring for your device
It is important that you regularly clean your AirCurve 10 device to make sure you receive optimal
therapy. The following sections will help you with disassembling, cleaning, checking and
reassembling your device.
WARNING
Regularly clean your tubing assembly, humidifier and mask to receive optimal therapy and to
prevent the growth of germs that can adversely affect your health.
Disassembling
1. Hold the humidifier at the top and bottom, press it gently and pull it away from the device.
2. Open the humidifier and discard any remaining water.
3. Hold the cuff of the air tubing and gently pull it away from the device.
4. Hold both the cuff of the air tubing and the swivel of the mask, then gently pull apart.
Cleaning
You should clean the device weekly as described. Refer to the mask user guide for detailed
instructions on cleaning your mask.

English 9
1. Wash the humidifier and air tubing in warm water using mild detergent.
2. Rinse the humidifier and air tubing thoroughly and allow to dry out of direct sunlight and/or heat.
3. Wipe the exterior of the device with a dry cloth.
Notes:
•The humidifier may be washed in a dishwasher on the delicate or glassware cycle (top shelf only).
It should not be washed at temperatures higher than 65ºC.
•Do not wash the air tubing in a dishwasher or washing machine.
•Empty the humidifier daily and wipe it thoroughly with a clean, disposable cloth. Allow to dry out
of direct sunlight and/or heat.
Checking
You should regularly check the humidifier, air tubing and the air filter for any damage.
1. Check the humidifier:
•Replace it if it is leaking or has become cracked, cloudy or pitted.
•Replace it if the seal is cracked or torn.
•Remove any white powder deposits using a solution of one part household vinegar to
10 parts water.
2. Check the air tubing and replace it if there are any holes, tears or cracks.
3. Check the air filter and replace it at least every six months. Replace more often if there are any
holes or blockages by dirt or dust.
To replace the air filter:
1. Open the air filter cover and remove the old air filter.
The air filter is not washable or reusable.
2. Place a new air filter onto the air filter cover and then close it.
Make sure the air filter is fitted at all times to prevent water and dust from entering the device.
Reassembling
When the humidifier and air tubing are dry, you can reassemble the parts.
1. Connect the air tubing firmly to the air outlet located on the rear of the device.
2. Open the humidifier and fill it with room temperature water up to the maximum water level
mark.
3. Close the humidifier and insert it into the side of the device.
4. Connect the free end of the air tubing firmly onto the assembled mask.