Resolution CryptiX RE601 Series User manual

RE601 Series CryptiX™Door Window Sensor
CryptiX Door Window Sensor is a full-featured security
transmitter with industry-leading wireless range and battery
life. It is typically used to sense opening and closing of
doors and windows, but can secure just about anything using
its two external contact zones. It will alarm when the magnet
is pulled away from the sensor or when an external contact is
opened.
Features
• Industry-leading wireless range and battery life
• One door window zone and two external contact zones
• Secure encrypted wireless transmissions
• 5 year warranty
Enroll by placing the panel into wireless enrollment mode
and then sending an enrollment signal from the sensor.
Alternatively, the sensor can be enrolled by scanning its bar
code using the HeliLink app or by entering its 8-character
serial number on the interactive service provider’s web portal.
Options for sending an Enrollment Signal
• Remove the battery tab, OR
• Remove the cover to trip tamper
Install by mounting the sensor and magnet on a door or
window using the mounting screw locations. Make sure to
align the alignment marks on the sensor and magnet when
mounting. Additionally, the sensor can be used with up to
two external contacts.
External Contacts (not evaluated by ETL)
• Use normally-closed contacts because the door
window sensor will transmit an alarm when it
sees an external contact open.
• Do not use end-of-line resistors.
• Wire contact wires to one or both outside
terminals, using the center terminal as
common.
CE installations must use a cover-securing screw.
Mounting Screw Holes
Cover-Securing Screw Hole
Use the Helix installation guide to verify proper system setup.
I
N
S
T
A
L
L
G
U
I
D
E
I

Pro Tips
3M VHB Tape works great if the surface is properly prepared and rm pressure is applied
for over 10 seconds.
Surface Preparation
• Clean the surface
• Ensure the mounting surface temperature is above 50 °F
Wireless performance is optimized when mounted near the top of the door in a vertical
orientation.
OK BESTWRONG
Wire an external contact by securing one wire in to either the external 1 or external 2
port and the other wire in to the common port. If two external contacts are used two
wires will be inserted into the common port.
Cover Tamper
Switch
Reed Switch
Battery +
-External 2
External 1
Common

X Axis
Z Axis
Magnet Gap Specications
Non-Ferromagnetic Surface
Nominal Mounting Distance
X Axis - Make
Break
Y Axis - Make
Break
Z Axis - Make
Break
1.00 inches (2.5 cm)
1.10 inches (2.8 cm)
1.30 inches (3.3 cm)
2.40 inches (6.1 cm)
2.55 inches (6.5 cm)
1.20 inches (3.0 cm)
1.35 inches (3.5 cm)
Ferromagnetic Surface
Nominal Mounting Distance
X Axis - Make
Break
Y Axis - Make
Break
Z Axis - Make
Break
0.50 inches (1.2 cm)
0.60 inches (1.5 cm)
0.65 inches (1.7 cm)
1.70 inches (4.3 cm)
1.75 inches (4.5 cm)
1.05 inches (2.7 cm)
1.10 inches (2.9 cm)
Y Axis

47-0004-08 • RevB • 2016-09-21
Tech Support Line [phone]
www.ResolutionProducts.com
WARRANTY
Resolution Products, Inc. will replace products that are defective in
their rst ve (5) years.
IC NOTICE
This device complies with Industry Canada license-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference
that may cause undesired operation of the device.
Le présent appareil est conforme aux cnr d’Industrie Canada
applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes:
(1) L’appareil ne doit pas produire de brouillage, et
(2) L’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
IC: 8310A-RE301
FCC NOTICE
This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference that may be received,
including interference that may cause undesired operation.
Changes or modications not expressly approved by the Resolution
Products, Inc. could void the user’s authority to operate this
equipment.
FCC ID: U5X-RE301
CE DECLARATION OF CONFORMITY
Hereby, Resolution Products, Inc. declares that this RE601-CE is
in compliance with the essential requirements and other relevant
provisions of directive 1999/5/EC.
(This declaration can be translated to other languages via a myriad
of translation tools found on the Internet.)
Specications subject to change without notice
Physical
Housing Dimensions
Weight with Battery
Mounting Fastener
3.25 x 1.40 x 1.05 inches (8.3 x 3.6 x 2.7 cm)
1.90 ounces (54 grams)
#4 or #6 screws (not provided)
Environmental
Operating Temperature
Maximum Humidity
32 to 120 °F (0 to 49 °C)
85% non-condensing relative humidity
Sensor Specications
Frequency
Replacement Battery
Nominal Battery Life
Battery Voltage
Current Draw
Transmitted Indications
433.92 MHz
One Panasonic CR123A
10 to 15 years
3.0 VDC (Nominal), 2.2 VDC (Low)
20 mA (Maximum), 0.6 uA (Quiescent)
Cover Tamper, Low Battery, Supervision
Certication
RE601
RE601-CE
UL634, ULC634, ETL, FCC, IC
EN50131-2-6, EN 60950-1, EN 300 220, EN 301 489,
CE Security Grade 1, CE Environmental Class 2, RCM
Specications