Resolution RE219 User manual

RE219_Honeywell_Flood_Temp_Instructions Page 1 of 4 27-Jan-15
24-Hour Tech Support Line: [phone]
www.ResolutionProducts.com
RE219 Flood/Temp Range, Honeywell
®
-Compatible
Home Disaster™ ensor
Features
• Tri-Mode Environmental Sensing:
o Flood/Moisture Sensor
o Freeze – for Furnace Failure
o verheat – for Furnace runaway or Air Conditioning failure.
• 3 unique wireless Loops: one for each function
• Cover tamper.
• Strong, reliable RF signal.
• 8-10 year battery life on CR123A battery.
• Low Battery indication.
• 3.3x1.4x1.1 inches.
Key Instructions
• Battery “+” faces towards spring.
• Enrolling:
To monitor multiple functions, repeat the below RF Enrollment process; each
time with the SAME serial number, but with a DIFFERENT Loop number.
Honeywell Vista and Lynx Settings
• Place Panel in Zone Programming mode (e.g. *56).
• Zone Type = for example, 24-Hr. Aux.
• Input Type = Supervised RF Transmitter.
• When asked for serial number, press Tamper switch.
• Program the desired Loop number you want that zone to monitor. Loop
functions are:
 Loop 1: verheat.
 Loop 2: Flood.
 Loop 3: Freeze.
 Loop 4: Tamper.
2GIG Go! Panel Settings – go to: Q1
2GIG® Settings for
Flood
:
Zone Type – [08] 24 Hr Aux
Equip Type – [8] water
Equip Code – [0556] existing
flood/temp sensor
Enter RF Serial - Press Shift +
Learn, Trip Zone
(verify ID with sensor label on
battery)
Equip Age – [0] New
oop – [2] (Flood)
Voice Desc: 087, 191
“Flood Sensor”
2GIG® Settings for
Freeze
:
Zone Type – [08] 24 Hr Aux
Equip Type – [6] freeze
Equip Code – [0556] existing
flood/temp sensor
Enter RF Serial - Press Shift +
Learn, Trip Zone
(verify ID with sensor label on
battery)
Equip Age – [0] New
oop – [3] (Freeze)
Voice Desc: 096, 191
“Freeze Sensor”
2GIG® Settings for
Overheat
:
Zone Type – [08] 24 Hr Aux
Equip Type – [10] temperature
Equip Code – [0708] existing
heat sensor
Enter RF Serial - Press Shift +
Learn, Trip Zone
(verify ID with sensor label on
battery)
Equip Age – [0] New
oop – [1] (Overheat)
Voice Desc: 112, 224, 191
“High Temperature Sensor”
RE219_Honeywell_Flood_Temp_Instructions Page 2 of 4 27-Jan-15
24-Hour Tech Support Line: [phone]
www.ResolutionProducts.com
• Test Temp alarm functions by putting in a freezer, or blowing a hair dryer on
sensor.
• Test Flood alarm function by putting sensor in water
(distilled water will not work, but tap water should).
N TE: Sensor reacts within 3 seconds when cover is off; 30 seconds when
cover on.
Operation
• Flood – Loop 2:
Alarm: when liquid rises 0.040 inches above sensor bottom.
Tamper: when cover is opened.
Supervisory: every hour.
• Freeze – Loop 3
Alarm: when room temperature drops below 40F.
Tamper: when cover is opened.
Supervisory: every hour.
• verheat – Loop 1
Alarm: when room temperature rises above 100F.
Tamper: when cover is opened.
Supervisory: every hour.

RE219_Honeywell_Flood_Temp_Instructions Page 3 of 4 27-Jan-15
24-Hour Tech Support Line: [phone]
www.ResolutionProducts.com
Specifications
Flood sensing: Titanium contacts
100K- hm nominal (D N T use an E L resistor)
Transmitter handles 1 or 2 flood elements, no more.
0.04 inch floor spacing to eliminate floor
condensation falses.
Checks for moisture every 5 seconds: needs two
positive moisture checks to send Flood alarm.
(test mode: every second when cover is off)
Freeze Alarm: 45F +/- 2F
Restores when temp increases 4F from alarm
verheat Alarm Temp: 100F +/- 2F
Restores when temp decreases 4F from alarm
Mounting hardware: #6 or #8 screws
Dual Mode mounting:
 Screwed to floor
 Screwed to wall
Terminal wire capacity: 16 Gauge
Replacement Battery: CR123A 1550 mAH
Temperature Range: 0F to 120F
Housing dimensions: 3.3x1.4x1.1 inches
Specifications subject to change without notice.
Internal & Close-up Pictures
Temp Element
Strain relief for
floor mounting
RE219_Honeywell_Flood_Temp_Instructions Page 4 of 4 27-Jan-15
24-Hour Tech Support Line: [phone]
www.ResolutionProducts.com
Notices
“GE”, “Honeywell”, and “DSC” are trademarks owned by General Electric Company, Honeywell
International Inc., and Tyco Safety Products Canada LTD, respectively.
Resolution Products, Inc. products will function with one of either GE, DSC or Honeywell systems.
However, no Resolution product is produced by, endorsed by, nor is officially associated with GE,
Honeywell or DSC. Resolution recommends verifying proper enrollment and operation, per control
panel installation instructions, at installation.
Warranty
Resolution Products, Inc. will replace products that are defective in their first five (5) years.
FCC Notice
This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions:
This device may not cause harmful interference.
This device must accept any interference that may be received, including interference
that may cause undesired operation.
Changes or modifications not expressly approved by the Resolution Products, Inc. could void
the user's authority to operate this equipment.
FCC ID: U5X-RE201X
IC Notice
This device complies with Industry Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions:
(1)This device may not cause interference, and
(2)This device must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :
(1)l'appareil ne doit pas produire de brouillage, et
(2)l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d'en compromettre le fonctionnement.
IC: 8310A-RE201