Resolution Honeywell RE210P User manual

Ceiling
Floor
RE210P Honeywell®Compatible PIR Motion Sensor
PIR Motion Sensor alarms when motion is sensed or when
the external contact is opened. It is battery powered and
requires no installation tools. A Pyroex™sensor with
HighBar™signal processing allows for industry-leading pet
immunity and catch performance.
Features
• Industry-leading pet immunity and catch performance
• Supports both motion zone and an external contact zone
• Mountable on walls or in corners
• 5 year warranty
Enroll by placing the panel into wireless enrollment mode and
then tripping the tamper three times.
Enrollment Tips
• Program as an RF type (Supervised RF)
• Loop 1 = Motion
• Loop 2 = External Contact
• Loop 4 = Tamper
Install using the included 3M VHB®tape to adhere the motion
sensor on a wall or in a corner. The tape should be applied
to the back when wall mounting or to the back bevels when
corner mounting. Alternatively, screw mounting can be
done by punching out the screw mounting holes.
Installation Tips
• Mount 7.5 to 9.5 feet from the oor for an
optimal balance between catch performance
and pet immunity.
• Remove the cover and circuit board before
trying to punch out the screw mounting holes.
• Ensure the bug foam stays intact and
snug around the IR sensing element when
re-installing the circuit board.
External Contact (not evaluated by ETL)
• Use a normally-closed contact because the
motion sensor will transmit an alarm when it
sees the external contact open.
• Do not use end-of-line resistors.
Mounting Screw Holes
Verify proper enrollment and operation using your control panel’s installation manual.
I
N
S
T
A
L
L
G
U
I
D
E
I

Pro Tips
Walk test mode is entered by pressing the motion
sensor’s tamper button. The walk test lasts three
minutes.
Walk Test Operation
• The walk test LED turns on when motion
is sensed.
• The motion sensor performs a
re-calibration after each activation. The
re-calibration takes about 30 seconds.
The sensor will NOT sense motion
during the re-calibration.
• Wireless transmissions are sent for each
detection, so walk test mode can also
be used to test the panel.
3M VHB tape works great if the surface is properly
prepared and rm pressure is applied for over 10
seconds.
Surface Preparation
• Clean the surface
• Ensure the mounting surface
temperature is above 50 °F
Motion lockout is active for three minutes after a motion event is detected. During the
motion lockout period, motion events will be ignored.
Motion sensitivity can be adjusted by the sensitivity jumper on the circuit board.
• Jumper Installed (lower sensitivity): Detects person in 3 to 5 steps.
Increases pet immunity. Usually for security applications.
• Jumper NOT Installed (higher sensitivity): Detects person in 2 to 4 steps.
Usually for occupancy applications.
Pet immunity is optimized when the motion sensor is mounted at 7.5 to 9.5 feet high
and aimed away from house features that could allow pets to be high in the detection
eld (e.g. stairs, counter tops, tall furniture).
Motion catch performance is best when the motion sensor is positioned so a person
would typically walk across the front of the motion sensor instead of directly toward
the motion sensor.
Motion Detection Tips
• Provide a clear line-of-sight to the monitored area and remember that glass
blocks infrared energy (PIR = Passive InfraRed).
• Aim away from windows and sunlight.
• Aim away from air conditioners, heaters or heating/cooling vents.
Walk Test LED
Cover Tamper Switch
Battery
Bug Foam IR Sensing Element
Sensitivity
Low - Jumper ON
High - Jumper OFF
External Contact
7.5ft
0
0 10ft 20ft 30ft 40ft
3.2ft

Accessories
Gimbal mount (RE019 and RE019-10) allows the motion sensor direction to be adjusted
after mounting on a wall.
Horizontal beam lens (RE020) has less look-down which results in increased pet
immunity.
Specications
Side eld of view for a mounting height of 7.5 feet
0
10ft
20ft
30ft
40ft
Top eld of view
010ft 10ft20ft 20ft30ft 30ft
7.5ft
3.2ft
010ft 20ft 30ft 40ft
3.2ft
9.5ft
6.4ft
010ft 20ft 30ft 40ft
Side eld of view for a mounting height of 9.5 feet

47-0005-02 • RevB • 2016-09-21
24-hour Tech Support Line [phone]
www.ResolutionProducts.com
WARRANTY
Resolution Products, Inc. will replace products that are defective in
their rst ve (5) years.
IC NOTICE
This device complies with Industry Canada license-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference
that may cause undesired operation of the device.
Le présent appareil est conforme aux cnr d’Industrie Canada
applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes:
(1) L’appareil ne doit pas produire de brouillage, et
(2) L’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
IC: 8310A-RE210P
FCC NOTICE
This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference that may be received,
including interference that may cause undesired operation.
Changes or modications not expressly approved by the Resolution
Products, Inc. could void the user’s authority to operate this
equipment.
FCC ID: U5X-RE210P
TRADEMARKS
“Honeywell” is a trademark owned by Honeywell International, Inc.
Resolution Products, Inc. products will function with Honeywell
systems. However, no Resolution product is produced by, endorsed
by, or is ofcially associated with Honeywell.
Resolution recommends verifying proper enrollment and operation,
per control panel installation instructions, at installation.
Specications
Physical
Housing Dimensions
Weight with Battery
Mounting Fastener
3.50 x 2.40 x 1.70 inches (8.9 x 6.1 x 4.3 cm)
3.2 ounces (91 grams)
3M VHB (Very High Bond) Tape or Screws (both provided)
Environmental
Operating Temperature
Maximum Humidity
32 to 120 °F (0 to 49 °C)
85% non-condensing relative humidity
Sensor Specications
Frequency
Pet Immunity
Replacement Battery
Nominal Battery Life
Battery Voltage
Current Draw
Optimal Mounting Height
Transmitted Indications
345 MHz
Two 60-pound dogs or one 85-pound dog
One Panasonic CR132A
6 to 8 years
3.0 VDC (Nominal), 2.2 VDC (Low)
30 mA (Maximum), 20 uA (Quiescent)
7.5 to 9.5 feet (2.3 to 3.0 m)
Cover Tamper, Low Battery, Supervision
Certication
RE210P UL639, ULC-S309-03, ETL, FCC, IC
Specications subject to change without notice