Resolution CryptiX Trident RE618 Series User manual

Use the Helix Installation Guide to verify proper system setup.
I
N
S
T
A
L
L
G
U
I
D
E
I
RE618 Series CryptiX™Trident™Environmental Sensor
Front slot
Mounting Screw Hole
Wall Clip
Trident 
conditions and reports extreme temperatures. It also reports
air temperature allowing custom high and low temperature trip
points to be set in the Helix panel.
Features
• Titanium probes for unmatched corrosion immunity
• IP67 rated waterproof enclosure
• GORE
®
vent to prevent seal failure
• 5 year warranty
Enroll by placing the panel into wireless enrollment mode
and then sending an enrollment signal from the sensor.
Alternatively, the sensor can be enrolled by scanning its bar
code using the HeliLink app or by entering its 8-character
serial number on the interactive service provider’s web
portal. NOTE, freeze and heat inputs must be enabled as
additional zones using the HeliLink app or the interactive
service provider’s web portal.
Options for sending an Enrollment Signal
• Remove the battery tabs, OR
• Remove the wall clip from Trident body
Install 
temperature detection. If desired, the wall clip can be used to
secure the Trident sensor.
Optional Screw Mounting
• Remove the wall clip from the Trident body.
• Secure the clip to a wall, baseboard or cupboard
using a #6 screw.
• Slide the Trident body down onto the wall clip
until it snaps into place.
Detects water pooled under the sensor and reports extreme
temperature conditions. High and low temperature trip points
are set in the Helix panel.
Default Temperature Trip Points
• Heat alarms when over 100°F (38°C)
• Heat restores when under 97°F (36°C)
• Freeze alarms when under 45°F (7°C)
• Freeze restores when over 48°F (9°C)
To replace the batteries,
the front slot and twist. Slide both old batteries out and the
new batteries in. To reinstall the cover, align the rear latches
and roll the cover forward until it snaps into place.

47-0028-08 • RevB • 2017-02-03
Tech Support Line [phone]
www.ResolutionProducts.com
WARRANTY
Resolution Products, Inc. will replace products that are defective in

IC NOTICE
This device complies with Industry Canada license-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference
that may cause undesired operation of the device.
Le présent appareil est conforme aux cnr d’Industrie Canada
applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes:
(1) L’appareil ne doit pas produire de brouillage, et
(2) L’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
IC: 8310A-RE318
FCC NOTICE
This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference that may be received,
including interference that may cause undesired operation.

Products, Inc. could void the user’s authority to operate this
equipment.
FCC ID: U5X-RE318
CE DECLARATION OF CONFORMITY
Hereby, Resolution Products, Inc. declares that this RE618-CE is
in compliance with the essential requirements and other relevant
provisions of directive 1999/5/EC.
(This declaration can be translated to other languages via a myriad
of translation tools found on the Internet.)
Pro Tips
The cover can be removed without removing the wall clip.
Both titanium probes must be in the same puddle for the Trident to detect water.
Tamper detection depends on how the Trident is installed.
• Trident secured to wall: Tamper is indicated when lifted off the clip.
• Trident NOT secured to wall: Tamper is indicated when the cover is removed.
When changing the batteries replace both with new batteries.

Physical
Housing Dimensions
Weight with Batteries
Mounting Fastener
2.43 x 2.48 x 1.17 inches (6.2 x 6.3 x 3.0 cm)
1.34 ounces (38 grams)
#6 screw (not provided)
Environmental
Operating Temperature
Maximum Humidity
Water Resistance
32°F to 120°F (0°C to 49°C)
85% non-condensing relative humidity
IP67 rated (waterproof for over 30 minutes at 1 meter depth)

Frequency
Replacement Batteries
Nominal Battery Life
Battery Voltage
Current Draw
Transmitted Indications
Temperature Accuracy
433.92 MHz
Two Panasonic CR2032
10 years
3.0 VDC (Nominal) 2.3 VDC (Low)
20 mA (Maximum) 0.5 uA (Quiescent)
Cover Tamper, Wall Tamper, Low Battery, Supervision
+/- 2°C

RE618
RE618-CE
FCC, IC, RCM
EN60950-1, EN300 220, EN301 489
