Resolution CryptiX NanoMax RE622 Series User manual

NanoMax is the smallest full-featured security transmitter
in the industry. It is typically used to sense opening and
closings of doors and windows, but can secure just about
anything using its Strip & Stick™external contact holes. It will
alarm when the magnet is pulled away from the NanoMax or
when the external contact is opened.
Features
• Quick peel and press mounting
• Small prole for a near invisible look
• Most exible magnet positioning in the industry
• Strip & Stick external contact holes
• 5 year warranty
Enroll by placing the panel into wireless enrollment mode
and then sending an enrollment signal from NanoMax.
Alternatively, NanoMax can be enrolled by scanning its bar
code using the HeliLink app or by entering its 8-character
serial number on the interactive service provider’s web
portal.
Options for sending an Enrollment Signal
• Remove the battery tab, which can be done
without removing the cover, OR
• Touch the magnet to the sensor 5 times within
5 seconds, OR
• Remove the cover to trip tamper
Install by removing the adhesive paper and adhering the
NanoMax and magnet on a door or window. Make sure to
align the alignment marks on the NanoMax and magnet
when mounting. Alternatively, NanoMax can be used with an
external contact instead of the reed switch.
External Contact (not evaluated by ETL)
• If you are using the external contact then you
cannot use the reed switch.
• Use a normally-closed contact because
NanoMax will transmit an alarm when it sees
the external contact open.
• Do not use end-of-line resistors.
• Connect the contact to NanoMax by inserting
the contact’s wires into the two Strip & Stick
holes on the back of NanoMax.
• Additional wiring information can be found by
searching www.ResolutionProducts.com for
“external contact wiring”.
RE622 Series CryptiX™NanoMax™Door Window Sensor
Use the Helix installation guide to verify proper system setup.
I
N
S
T
A
L
L
G
U
I
D
E
I

Pro Tips
3M VHB Tape works great if the surface is properly prepared and rm pressure is applied
for over 10 seconds.
Surface Preparation
• Clean the surface
• Ensure the mounting surface temperature is above 50 °F
Wireless performance is optimized when mounted near the top of the door in a vertical
orientation.
OK BESTWRONG
Accessories
MetalMax™ NanoMax Mounts (RE033-16) can
be used for better performance on metal and
narrow mounting situations.
• Improves wireless performance by
moving the internal antenna away from
metal surfaces.
• Provides an alternate mounting
orientation for narrow installs.
• Increases magnet gap distance on
metal surfaces.

Non-Ferromagnetic Surface
Nominal Mounting Distance
X Axis - Make
Break
Y Axis - Make
Break
Z Axis - Make
Break
0.75 inches (2.0 cm)
0.90 inches (2.3 cm)
0.95 inches (2.5 cm)
1.70 inches (4.3 cm)
1.75 inches (4.5 cm)
1.10 inches (2.8 cm)
1.15 inches (3.0 cm)
Ferromagnetic Surface (Using RE033 Mount)
Nominal Mounting Distance
X Axis - Make
Break
Y Axis - Make
Break
Z Axis - Make
Break
0.50 inches (1.2 cm)
0.55 inches (1.4 cm)
0.60 inches (1.5 cm)
1.50 inches (3.8 cm)
1.55 inches (4.0 cm)
0.70 inches (1.8 cm)
0.75 inches (2.0 cm)
Magnet Gap Specications
Y Axis
Z Axis
X Axis

47-0006-08 • RevC • 2016-09-21
Tech Support Line [phone]
www.ResolutionProducts.com
WARRANTY
Resolution Products, Inc. will replace products that are defective in
their rst ve (5) years.
IC NOTICE
This device complies with Industry Canada license-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference
that may cause undesired operation of the device.
Le présent appareil est conforme aux cnr d’Industrie Canada
applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes:
(1) L’appareil ne doit pas produire de brouillage, et
(2) L’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
IC: 8310A-RE322
FCC NOTICE
This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference that may be received,
including interference that may cause undesired operation.
Changes or modications not expressly approved by the Resolution
Products, Inc. could void the user’s authority to operate this
equipment.
FCC ID: U5X-RE322
CE DECLARATION OF CONFORMITY
Hereby, Resolution Products, Inc. declares that this RE622-CE is
in compliance with the essential requirements and other relevant
provisions of directive 1999/5/EC.
(This declaration can be translated to other languages via a myriad
of translation tools found on the Internet.)
Physical
Housing Dimensions
Weight with Battery
Mounting Fastener
1.80 x 0.77 x 0.39 inches (4.6 x 2.0 x 1.0 cm)
0.53 ounces (15 grams)
3M VHB Tape
Environmental
Operating Temperature
Maximum Humidity
32 to 120 °F (0 to 49 °C)
85% non-condensing relative humidity
Sensor Specications
Frequency
Replacement Battery
Nominal Battery Life
Battery Voltage
Current Draw
Transmitted Indications
433.92 MHz
One Panasonic CR1632
6 years
3.0 VDC (Nominal), 2.62VDC (Low)
20 mA (Maximum), 0.5uA (Quiescent)
Cover Tamper, Low Battery, Supervision
Certications
RE622
RE622-CE
UL634, ULC634, ETL, FCC, IC
EN 60950-1, EN 300 220, EN 301 489, CE, RCM
Specication subject to change without notice
Specications