RiverRidge 06-040 User manual

ASSEMBLY INSTRUCTIONS
RiverRidge® SOMERSET SPACE SAVER
ITEM #:06-040 WHITE
ITEM #:06-079 GRAY

Send requests for missing or damaged parts replacements by email to:
[e-mail] or call toll free 1-(844)-223-5201 or order parts on line at
www.riverridgehome.com
THIS SHELF UNIT WILL HOLD UP TO 25 POUNDS PER SHELF OR A TOTAL OF 75 POUNDS. DO
NOT LOAD EACH SHELF WITH MORE THAN 25 POUNDS. IF LOADED WITH MORE THAN 25
POUNDS PER SHELF AS THIS MAY CAUSE DAMAGE TO THE SHELF AND MAY CAUSE SERIOUS
INJURY OR DEATH.

PARTS LIST
NO
PARTS
QTY
DESCRIPTION
1
1PC LEFT DOOR
2
1PC RIGHT DOOR
3
1PC UPPER RIGHT SIDE
PANEL
4
1PC UPPER LEFT SIDE PANEL
5
1PC UPPER SECTION CROSS
BAR
6
1PC SHELF
7
1PC TOP BOARD
8
1PC
MIDDLE CONNECTION
BOARD
9
1PC UPPER BACK BOARD
10
1PC MIDDLE BACK BOARD
11
1PC
LOWER BACK BOARD
12
1PC ADJUSTABLE SHELF
13
1PC RIGHT SUPPORT BOARD
14
1PC LEFT SUPPORT BOARD
15
2PCS
LOWER SECTION TOP
CROSS BAR
16
1PC REAR LOWER CROSS
BAR
17
1PC LOWER LEFT SIDE PANEL
18
1PC LOWER RIGHT SIDE
PANEL

NO PARTS QTY DESCRIPTION
A
34PCS WOOD DOWEL
B
16PCS CAM BOLT (SMALL)
C
16PCS CAM LOCK (SMALL)
D
8PCS CAM BOLT (LARGE)
E
8PCS CAM LOCK (LARGE)
F
26PCS WOOD SCREW 3X10MM
G
4PCS HINGE
H
2PCS MAGNET PLATE
I
20PCS WOOD SCREW 3X12MM
J
1SET MAGNET WITH 2SCREWS
K
4PCS SHELF HOLDER
L
4PCS MACHINE SCREW 4X15MM
M
2PCS HANDLE
N
2PCS PLASTIC ANCHOR
O
2PCS WOOD SCREW 4X40MM
P
1PC
PLASTIC CONNECTION
STRIP

H
L
L
2
M
STEP 1 F
STEP 1
1. Attach 1 magnet plate (H) to left door (1) by inserting 1 wood screw (F) through hole on magnet plate (H)
and tighten to left door (1).
2. Attach 1 handle (M) to left door (1) by inserting 2 machine screws (L) through holes on left door (1) and
tighten to handle (M).
3. Repeat above steps to assemble another magnet plate (H) and handle (M) to right door(2).
STEP 2
STEP 2
1. Insert 2 wood dowels (A) into dowel holes on right support board (13) .
2. Screw 3 cam bolts (small-B) into pre-threaded holes on right support board (13).
3. Attach 2 hinges (G) to right support board(13).
4. Insert 6 wood screws (F) through holes on hinges (G) and tighten to right support board (13).
5. Repeat above steps to assemble left support board (14) and another 2 hinges(G).
F
L
L
H
1
M

STEP 3
STEP 3
1. Attach right support board (13) to upper right side panel (3) by inserting wood dowels (A) into dowel holes
and inserting cam bolts (small-B) into cam lock holes on upper right side panel(3).
2. Insert 3 cam locks (small-C) into cam lock holes on upper right side panel (3) and rotate clockwise to secure
cam bolts (small-B) in place.
3. Repeat above steps to assemble upper left side panel (4) and right support board(14).
STEP 4
STEP 4
1. Screw 2 cam bolts (small-B) into pre-threaded holes on upper left side panel (4) and upper right side panel (3).
2. Insert 8 wood dowels (A) into dowel holes on upper left side panel (4) and upper right side panel(3).
3. Attach upper section cross bar (5) to upper left side panel (4) by inserting wood dowels (A) into dowel
holes on the upper section cross bar (5).
4. Attach shelf (6) to upper left side panel (4) by inserting cam bolt (small-B) and wood dowels (A) into holes on
shelf (6), then insert 1 cam lock (small-C) into cam lock hole on shelf (6) and rotate clockwise to secure cam
bolt (small-B) in place.
5. Attach upper right side panel (3) to upper section cross bar (5) and shelf (6) by inserting wood dowels (A) into
holes on upper section cross bar (5), shelf (6) and inserting cam bolt (small-B) into holes on shelf(6).
6. Insert 1 cam lock (small-C) into cam lock hole on shelf (6) and rotate clockwise to secure cam bolt (small-B)
in place.

STEP 5
STEP 5
1.Attach magnet (J) to bottom of top board (7) by inserting 2 wood screws through holes on magnet (J) and
tighten to top board (7).
2. Screw 4 cam bolts (small-B) into pre-threaded holes on top board (7).
3. Insert 4 wood dowels (A) into dowel holes on top board (7).
4.Attach top board (7) to upper left side panel (4) and upper right side panel (3) by inserting wood dowels
(A) into dowel holes and cam bolts (small-B) into cam lock holes on upper left side panel (4) and upper
right side panel (3).
5.Insert 4 cam locks (small-C) into cam lock holes on upper left side panel (4) and upper right side panel (3),
and rotate clockwise to secure cam bolts (small-B) in place.
STEP 6
STEP 6
1. Screw 6 cam bolts (large-D) into pre-threaded holes on lower left side panel (17) and lower right side panel (18).
2. Insert 6 wood dowels (A) into dowel holes on lower left side panel (17) and lower right side panel(18).
3. Attach 2 lower section top cross bars (15) to lower left side panel (17) and lower right side panel (18) by
inserting wood dowels (A) into dowel holes and cam bolts (large-D) into cam lockholes.
4. Insert 4 cam locks (large-E) into cam lock holes on lower section top cross bars (15) and rotate
clockwise to secure cam bolts (large-D) in place.
5. Attach rear lower cross bar (16) to lower left side panel (17) and lower right side panel (18) by inserting wood
dowels (A) into the dowels holes and cam bolts (large-D) into cam lockholes.
6. Insert 2 cam locks (large-E) into cam lock holes on lower section top cross bars (16) and rotate
clockwise to secure cam bolt (large-D) in place.

STEP 7
STEP 7
1. Screw 2 cam bolts (large-D) into pre-threaded holes on middle connection board(8).
2. Insert 8 wooden dowels (A) into holes on lower left side panel (17), lower right side panel (18) and lower
section top cross bars (15).
3. Turn over middle connection board (8) and attach to pre-assembled lower left side panel (17), lower right side
panel (18) and lower section top cross bars (15) by inserting wood dowels (A) into dowel holes and inserting
cam bolts (large-D) into cam lock holes on the lower left side panel (17), lower right side panel (18) and lower
section top cross bars (15).
4. Insert 2 cam locks (large-E) into cam lock holes on lower left side panel (17) and lower right side panel (18)
and rotate clockwise to secure cam bolts (large-D) in place.

STEP 8
STEP 8
1. Screw 4 cam bolts (small-B) into pre-threaded holes on middle connection board(8).
STEP 9
STEP 9
1. Attach upper assembled section to lower assembled section by inserting 4 wood dowels (A) into dowel
holes and inserting cam bolts (small-B) into cam lock holes on upper left side panel (4) and upper right side
panel (3).
2. Insert 4 cam locks (small-C) into cam lock holes on upper left side panel (4) and upper right side panel (3) and
rotate clockwise to secure cam bolts (small-B) in place.
B
8
18
17
3
A
4
C
18
17

2
1
F
9
P
10
9
10
11
STEP 10
I
STEP 10
1.Attach upper back board (9) and middle back board (10) together by sliding into plastic connection strip (P).
2.Attach upper back board (9) and middle back board (10) to assembled cabinet by inserting 7 wood screws (I)
through holes on upper back board (9) and 4 wood screws (I) through holes on middle back board (10), then
tighten to cabinet.
3.Attach lower back board (11) to cabinet by inserting 7 wood screws (I) through holes on lower backboard
(11) and tighten to cabinet.
4.Insert 2 wood screws (I) through holes on joint area of middle back board (10) and lower back board (11)
and tighten to cabinet.
STEP 11
STEP 11
1.Attach left door (1) to left side panel (3) by inserting 6 wood screws (F) through holes on hinges (G) and
tighten to left door (1).
2.Repeat above step to assemble right door(2).
3.Adjust hinges to make doors close tight as needed.
90°
I

5
O
STEP 12
STEP 12
1. Place drawing with hole positions on wall in desired position and drill 2 holes.
2.Insert 2 plastic anchor (N) into holes on wall and attach cabinet in place by inserting 2 long screws (O)
through holes on upper section cross bar (5) and tighten into plastic anchors (N) in wall.
STEP 13
STEP 13
1. Insert 4 shelf holders (K) into holes on upper left side panel (4) and upper right side panel(3).
2. Make sure 4 shelf holders (I) are at same height.
3. Place adjustable shelf (12) onto shelf holders(I).
N
O
3
12
K
3