RiverRidge SOMERSET 06-038 XS User manual

ASSEMBLY INSTRUCTIONS
RiverRidge® SOMERSET 2 DOOR FLOOR CABINET
ITEM #: 06-038 XS WHITE
ADULT ASSEMBLY REQUIRED
This product requires assembly by an adult because of the small parts. Care should be
taken in unpacking and assembling this item to keep the small parts away from children.
WARNING
Young children can be seriously injured or killed, if furniture tips over.
Don’t use this item for a TV stand.
Use angle-braces or anchors to secure furniture to the wall.

Send requests for missing or damaged parts replacements by email to :
[email protected] or call toll free 1-(844)-223-5201 or order parts on line at
www.riverridgehome.com
THIS SHELF UNIT WILL HOLD UP TO 25 POUNDS PER SHELF OR A TOTAL OF 75 POUNDS. DO
NOT LOAD EACH SHELF WITH MORE THAN 25 POUNDS. IF LOADED WITH MORE THAN 25
POUNDS PER SHELF AS THIS MAY CAUSE DAMAGE TO THE SHELF AND MAY CAUSE SERIOUS
INJURY OR DEATH.

PARTS LIST

TOOLS NEEDED FOR ASSEMBLY : FLAT & PHILIPS SCERWDRIVER (NOT INCLUDED)
THE USE OF POWER SCREWDRIVER IS NOT RECOMMENED

STEP1
STEP1
1. Attached drawer left side panel (12) to drawer back board (14) by inserting 2pc long wood screws (M)
through holes on the left side panel (12), then tighten into drawer back board (14).
2. Attached drawer right side panel (11) to drawer back board (14) by inserting 2pc long wood screws (M)
through holes on the right side panel (11),then tighten into drawer back board (14).
3. Slide the drawer bottom board (13) into the grooves on the drawer left side panel (12), drawer right side
panel (11) and drawer back side panel (14).
STEP2
STEP2
1. Screw in 2 cam bolts (B) into the pre-threaded holes on the drawer front board (10).
2. Insert 4 wood dowels (A) into dowel holes on the drawer front board (10).
3. Attached drawer front board (10) to drawer left side panel (12), drawer right side panel (11) and drawer
bottom board (13) by inserting the dowels(A) into dowel holes and inserting the cam bolt (B) into the
cam lock holes on the drawer left side panel (12), drawer right side panel (11) and inserting the drawer
bottom board (13) into the groove on the drawer front board (10).
4. Insert 2 cam locks (C) into the cam lock holes on the drawer left side panel (12) and drawer right side
panel (11) separately, then rotate clockwise to secure the cam bolts (B) in place.
5. Attach 1 handle (K) to drawer front board (10) by inserting 2 mchine screws (J) through the holes on the
drawer front board (10) then tighen to the handle (K).

STEP3
STEP3
1. Put the assembled drawer upside down.
2. Attach the drawer slides attach to drawer (W) to drawer right side panel (11) by inserting 2 wood screws
(L) through holes on the drawer slides attach to drawer (W), then tighten into drawer right side panel (11)
by using a Philips screwdriver.
3. Attach the drawer slides attach to drawer (W) to drawer left side panel (12) by inserting 2 wood screws (L)
through holes on the drawer slides attach to drawer (W), then tighten into drawer left side panel (12) by
using a Philips screwdriver.
STEP4
STEP4.
1. Screw in 3 cam bolts (B) into the pre-threaded holes on the left support board (6).
2. Insert 3 wood dowels (A) into the dowel holes on the left support board (6).
3. Attach left support panel (6) to left side panel (1) by inserting the wood dowels (A) into the dowel holes
and inserting the cam bolts (B) into the cam lock holes on the left side panel (1).
4. Insert 3 cam locks (C) into the cam lock holes on the left side panel (1), then rotate clockwise to secure
the cam bolts (B) in place.

STEP5
STEP5
1. Screw in 3 cam bolts (B) into the pre-threaded holes on the right support board (3).
2. Insert 3 wood dowels (A) into the dowel holes on the right support board (3).
3. Attach right support panel (3) to right side panel (2) by inserting the wood dowels (A) into the dowel
holes and inserting the cam bolts (B) into the cam lock holes on the right side panel (2).
4. Insert 3 cam locks (C) into the cam lock holes on the right side panel (2), then rotate clockwise to secure
the cam bolts (B) in place.
STEP6
STEP6
1. Attach the drawer slides attach to side panel (V) to left side panel (1) by inserting 2 wood screws (L)
through the holes on the drawer slides attach to side panel (V) then tighten into left side panel (1).
2. Attach 2 Hinge (E) to left side panel (1) by inserting 4 wood screws (D) through the holes on the Hinge (E)
then tighten to left side panel (1).

STEP7
STEP7
1. Attach the drawer slides attach to side panel (V) to right side panel (2) by inserting 2 wood screws (L)
through the holes on the drawer slides attach to side panel (V) then tighten into right side panel (2).
2. Attach 2 Hinge (E) to right side panel (2) by inserting 4 wood screws (D) through the holes on the Hinge (E)
then tighten to right side panel (2).
STEP8
STEP8
1. Screw in 6 cam bolts (B) into the pre-threaded holes both on left side panel (1) and right side panel (2)
separately by using a Philips screwdriver.
2. Insert 6 wood dowels (A) into dowel holes on left side panel (1) and right side panel (2) separately.
3. Attach cross bar (4) to left side panel (1) by inserting wood dowel (A) and cam bolt (B) into holes on the
cross bar(4), then insert 1 cam lock (C) into cam lock hole on the cross bar (4) and rotate clockwise to
secure the cam bolt (B) in place.
4. Attach bottom board (5) to left side panel (1) by inserting 2 wood dowels (A) and 2 cam bolts (B) into
holes on bottom board (5), then insert 2 cam locks (C) into cam lock holes on the bottom board (5) and
rotate clockwise to secure 2 cam bolts (B) in place..
5. Attach right side panel (2) to cross bar (4) and bottom board (5) by inserting wood dowels (A) and Cam
bolts (B) into holes on cross bar (4) and bottom board (5).
6. Insert 2 cam locks (C) into cam lock holes on bottom board (5) and rotate clockwise to secure 2 cam bolts (B) in place.
7. Insert 1 cam lock (C) into cam lock hole on cross bar(4) and rotate clockwise to secure the cam bolt (B) in place .
8. Attach the magnet (H) to cross bar (4) by inserting 2 wood screws (D) through holes on the magnet (H),
then tighten into the cross bar (4) by using a Philips screwdriver.

STEP9
STEP9
1.Insert 4 wood dowels (A) into dowel holes on top of left side panel (1) and right side panel (2) separately.
2.Screw in 4 cam bolts (B) into the pre-threaded holes on top board (7).
3.Attach top board (7) to left side panel (1) and right side panel (2) by inserting 4 wood dowels (A) into dowel
holes on top board (7), and inserting 4 cam bolts (B) into cam lock holes on left side panel (1) and right side
panel (2).
4.Insert 2 cam locks (C) into cam lock holes on left side panel (1) and rotate clockwise to secure 2 cam bolts (B) in place.
5.Insert 2 cam locks (C) into cam lock holes on right side panel (2) and rotate clockwise to secure 2 cam bolts (B) in place.
STEP10
STEP10
1. Attach the left door (15) to left side panel (1) by inserting 4 wood screws (D) through holes on Hinges (E) then tighten to
the left door (15).
2. Attach the handle (K) to left door (15) by inserting 2 machine screws (J) through holes on the left door (15)
then tighten to the handle (K).
3. Attach the Magnet plate (F) to left door (15) by inserting 1 wood screw (D) through the holes on the
Magnet plate (F) then tighten to the left door (15).
4. Repeat the above 3 steps to assemble the right door (16) to right side panel (2) and assemble the handle (K), Magnet
plate(F) to right door (16).

STEP11
STEP11
1. Attach drawer to cabinet by sliding 2 drawer slider with wheels (N) into 2 drawer sliders which already
assembled to the cabinet.
2. Insert 8 shelf holders (I) into holes on left side panel (1) and right side panel (2).
3. Make sure the 8 shelf holders (I) on the same height.
4. Put the 2 shelves (9) onto the shelf holders (I).
STEP12
STEP12
1.Attach 2pc back board (8) to the pre-assembled cabinet by inserting 18 wood screws (G) through holes on back
board (8), then tighten into the cabinet.

STEP13
STEP13
1. Attach the metal bracket (s) to the back board (8).
2.Insert 1 wood screw (U) through hole on the metal bracket (S) then tighten to the back board (8) and top board
(7) by using a Philips screwdriver.
3.According to the position of the metal bracket (s) which assembled to the cabinet then drill hole on the wall.
4.Insert 1 plastic anchor (Q) into hole on the wall then attach another metal bracket (S) to the anchor (Q).
5.Insert 1 long screw (R) through metal bracket (S) then tighten to plastic anchor (Q).
STEP14
STEP14
1.Place the cabinet against the wall.
2.Insert a plastic lock trip (T) through the metal bracket (S) on the cabinet then through the metal bracket (S) on
the wall, fasten the plastic lock trip (T) to fix 2 metal brackets (S) firmly.

ENJOY YOUR NEW RiverRidge® CABINET NOW !
Attention Adults: The cabinet should be checked periodically for damage or loose screws/parts.
Take appropriate action necessary to correct the hazard such as tightening of screws and taking
any damaged parts away from the children.
Thank you for purchasing this RiverRidge® Home Products item. We hope you enjoy it, and
consider purchasing other RiverRidge® items.
Send requests for missing or damaged parts replacements by email to :
[email protected] or call toll free 1-(844)-223-5201 or order parts on line at
www.riverridgehome.com
RiverRidge® is a registered trademark of Sourcing Solutions, Inc., Hudson, WI 54016.