Roger PSD4D User manual

Roger Access Control System
PSD4D Power Supply and Bus Distributor
Operating Manual
Product version: 1.0
Document version: Rev. C

PSD4D Operating Manual.doc 2019-01-24
2/11
Design and application
PSD4D distributes power supply and RS485 bus to 4 doors. For each door it offers RS485 interface, 1.0A
main power supply output and 0.2A auxiliary power supply. Short circuit at output and communication lines
of particular door do not affect lines at remaining doors. The PSD4D is supplied from the 13.8VDC PSU
which provides power for electronic module and door equipment, including door lock and readers. In case
the external power supply is lost, the system is supplied from the backup battery connected to the PSD4D
distributor and charged with 0.3A, 0.6A or 0.9A current. PSD4D is equipped with removable terminal blocks
which facilitate electrical connections during installation and maintenance. The PSD4D distributor is mainly
used in access control systems with MCT-IO readers which are equipped with on-board inputs and outputs.
Characteristics
Power supply distribution to 4 doors
RS485 bus distribution to 4 doors
4 supply outputs 12V/1.0A
4 supply outputs 12V/0.2A
Power supply lost signalling output
Battery charging with 0.3A, 0.6A or 0.9A current
Protection against deep battery discharge
Supplied from 13.8VDC/5.4A PSU e.g. PS4D
Fig. 1 General concept of PSD4D distributor

PSD4D Operating Manual.doc 2019-01-24
3/11
Fig. 2 Access system for 8 doors with MCT-IO series readers and PSD4D distributors (example)
Fig. 3 Access system for 16 doors with MCT-IO readers and PSD4D distributors (example)

PSD4D Operating Manual.doc 2019-01-24
4/11
Power supply
The nominal 13.8VDC power source is required to supply PSD4D. The PS4D power supply from Roger is
recommended. Due to relatively high current, connection between distributor and PSU should be made
using short cables with adequate cross sections. Multiple PSD4D distributors can be supplied from the
same PSU but in such a case each distributor should be connected to PSU using separate cable. In order to
avoid voltage reduction it is recommended to install PSD4D distributor close to the PSU, preferable in the
same enclosure. When PSD4D supply voltage is too low, the battery cannot be fully charged and when the
voltage is too high the battery can be damaged. If the PSD4D is supplied from the power source which is
equipped with its own backup battery (e.g. UPS) the PSD4D can work without battery and can be supplied
from 12-15V range.
Note: The PS4D can provide 5,4A continues output current. If PSD4D is expected to provide the maximal
output current (4 doors with 1,2A and 0,9A battery charging current) the 6,0A supply source is required.
Fig. 4 Supplying 2 PSD4D modules from the same PSU (example)
Backup battery
PSD4D enables battery charging with 0.3A, 0.6A or 0.9A current and up to the voltage which is equal to
supply voltage (nominally 13.8VDC). The battery charging current is selected with jumpers. When battery
voltage drops to approximately 10V then it is disconnected from the distributor. The battery is reconnected
when power supply is restored. In order to ensure battery charging up to 80% level within 24h (according to
EN 60839 standard) the following current settings must be applied:
0.3A for 7Ah battery
0.6A for 17Ah battery
0.9A for 24Ah battery

PSD4D Operating Manual.doc 2019-01-24
5/11
RS485 Bus Distribution
PSD4D is connected to the controller’s RS485 bus but it does not occupy any address. The bus is
distributed to each controlled door. Each reader connected to the distributor must have unique address.
Addressing of the readers can be done during low level configuration by means of RogerVDM software or
manually, during memory reset procedure.
Fig. 5 RS485 bus distribution to readers
VDR Power Output
VDR power supply output is dedicated to supply door lock, alarm signalling device and other door related
devices. The terminal VDR+ provides supply plus and is protected with 1.0A electronic fuse. The terminal
VDR- provides supply minus and is internally shorted with system ground. Green LED indicator is located at
VDR+ terminal to signal voltage at the output.
TML Power Output
TML power supply output is dedicated to supply readers. The terminal TML+ provides supply plus and is
protected with 0.2A electronic fuse. The terminal TML- provides supply minus and is internally shorted with
system ground. Green LED indicator is located at TML+ terminal to signal voltage at the output.
VOUT Power Output
VOUT power supply output is dedicated to supply additional electronic modules including access controller.
The terminal VOUT+ provides supply plus and is protected with 0.2A electronic fuse. The terminal VOUT-
provides supply minus and is internally shorted with system ground. Green LED indicator is located at
VOUT+ terminal to signal voltage at the output.
Note: If access controller is supplied from own PSU and connected with own backup battery then it cannot
be at the same time supplied from PSD4D.
AUX Power Output
AUX power supply output is dedicated to supply additional electronic devices in vicinity of the distributor.
The terminal AUX+ provides supply plus and is protected with 0.2A electronic fuse. The terminal AUX-
provides supply minus and is internally shorted with system ground. Green LED indicator is located at
AUXT+ terminal to signal voltage at the output.

PSD4D Operating Manual.doc 2019-01-24
6/11
ACL Signalling Output
The ACL is a 15mA rated transistor output. When switched off it remains in high resistance. It shorts to
ground to ground if power supply is lost. In order to monitor power supply status it should be connected to
any system input programmed for [116]: AC Lost Status function.
Note: Multiple ACL outputs can be connected to the same monitoring input but in such case it is not possible
to distinguish the source of failure.
Door Control
PSD4D distributes power supply and RS485 communication bus to all 4 doors. For each door, it offers 1.0A
main power supply (VDR+/VDR- terminals), 0.2A auxiliary power supply (TML+/ TML- terminals) and
communication bus (A/B terminals). The 1.0A output is dedicated to supply door lock and other equipment
(e.g. alarm siren, door bell etc.). The 0.2A output is dedicated to supply readers. Supply outputs are
protected against overload with electronic fuses and separated is such a way that overload or shortage on
one supply output doesn’t affect other supply outputs. The A/B lines are dedicated to door readers.
Door Control with MCT-IO Readers
In this scenario of operations MCT-IO reader is used to control door using its own, on-board IO lines. The
MCT-IO readers offer 3 input and 3 outputs including one relay output. These lines usually are enough to
control door thus no extra IO lines at the controller or expander are required. In typical scenario, door lock is
controlled by relay output while alarm signalling device is controlled by transistor output. Both devices are
triggered by shorting to ground. If the door is read-in/read-out type then additional MCT reader (without built-
in IOs) should be installed. Due to security reasons it is recommended to install MCT-IO reader on the
internal (safe) side of the door while MCT reader on the external (public) door side. In the example below,
door contact and exit button are connected to MCT-IO reader.
Fig. 6 Read-in/read-out door control with MCT-IO and MCT readers (example)
Connection to Access Controller
MC16 access controller can be supplied from own transformer and operate with its own battery or, as shown
on the figure below, it can be supplied from the PSD4D distributor. In the diagram below entire system is
supplied from the same PSU. If the controller is supplied from the transformer or other power source, then it
is necessary to short controller ground (AUX-) with distributor ground (VOUT-).

PSD4D Operating Manual.doc 2019-01-24
7/11
Fig. 7 Access controller supplied from the PSD4D distributor
System with Multiple Distributors
The example below presents access system with MC16 controller operating with 3 PSD4D distributors.
Each PSD4D operates with its own battery and is supplied from its own PSU. The PSU should be installed
close to the distributor, preferably in the same enclosure.
Fig. 8 Access system with 3 PSD4D distributors and MC16 controller (example)

PSD4D Operating Manual.doc 2019-01-24
8/11
Installation
The PSD4D distributor is factory equipped with the plastic clips which enable its installation on the DIN rail.
If required, plastic clips can be removed and then module can be installed on flat surface. All electric
connections should be done when entire system is without power supply. It is recommended to install the
distributor in the same enclosure as PSU. The wires which supply the distributor should have adequate
cross section so the voltage drop would not exceed 200mA. It is recommended to use wires with minimal
cross section 1mm2and length up to 30cm. Such wires are included with PSxD power supplies.
Fig. 9 PSD4D module view
Battery Charging Current Selection
300 mA; recommended current for 12V/7Ah battery
600 mA; recommended current for 12V/17Ah battery
900 mA; recommended current for 12V/24Ah battery
Connection Terminals
Name
Function
BAT+
Battery plus
BAT-
Battery minus
AUX+
13.8VDC/0.2A auxiliary power output plus
AUX-
13.8VDC/0.2A auxiliary power output minus
VOUT+
13.8VDC/0.2A auxiliary power output plus
VOUT-
13.8VDC/0.2A auxiliary power output minus
VIN+
13.8VDC power input plus

PSD4D Operating Manual.doc 2019-01-24
9/11
VIN-
13.8VDC power input minus
A
RS485 communication bus input, line A
B
RS485 communication bus input, line B
ACL
Power supply lost signalling output
Note: Following terminals are replicated 4 times on the PSD4D module. The letter “x” stands for
door number (1-4).
VDRx+
13.8VDC/1.0A main power output plus
VDRx-
13.8VDC/1.0A main power output minus
TMLx+
13.8VDC/0.2A terminal power output plus
TMLx-
13.8VDC/0.2A terminal power output minus
Ax
RS485 communication bus output, line A
Bx
RS485 communication bus output, line B
Technical Specification
Power supply
13.8VDC; +/- 100mV
Supply current
Up to 6,0A (depend on the expected electrical loads)
AUX+/AUX- auxiliary power output
13.8VDC/0.2A; overload protection
VOUT+/VOUT- auxiliary power output
13.8VDC/0.2A; overload protection
VDRx+/VDRx- main power output
13.8VDC/1.0A; overload protection
TML+/TML- terminal power output
13.8VDC/0.2A; overload protection
Power supply lost output
15VDC/15mA; overload protection
Battery charging current
0.3A; 0.6A; 0.9A
Battery cut-off voltage
App. 10.0V
Distributor to controller cable length
Max. 1200m
Distributor to terminal cable length
Max. 150m
Environmental class
Class I, indoor general conditions, temperature: +5°C to
+40°C, relative humidity: 10 to 95% (no condensation)
Dimensions
96 x 80 mm
Weight
85 g
Certificates
CE
Ordering Information
Product
Description
PSD4D
Power Supply and Communications Bus Distributor
Product History
Version
Date
Description
PSD4D v1.0
10/2017
First commercial version of the product

PSD4D Operating Manual.doc 2019-01-24
10/11
This symbol placed on a product or packaging indicates that the product
should not be disposed of with other wastes as this may have a negative
impact on the environment and health. The user is obliged to deliver
equipment to the designated collection points of electric and electronic
waste. For detailed information on recycling, contact your local authorities,
waste disposal company or point of purchase. Separate collection and
recycling of this type of waste contributes to the protection of the natural
resources and is safe to health and the environment. Weight of the
equipment is specified in the document.
Contact:
Roger Sp. z o. o. sp. k.
82-400 Sztum
Gościszewo 59
Tel.: [phone]
Fax: [phone]
Tech. support: [phone]
E-mail: [e-mail]
Web: www.roger.pl

PSD4D Operating Manual.doc 2019-01-24
11/11
1. Metryka dokumentu
Wersja
1.00
Poprawka
Rev. A
Opracował
G. Wensker
Właściciel
G. Wensker
Archiwum
Dokument dozorowany
Tak
Dokument wewnętrzny
Nie
Wersja robocza
Tak
2. Historia dokumentu
Wersja
Data
Opis
1.0 Rev. A
Pierwsze wydanie
1.0 Rev.B
09/2018
Dodane informacje o AUX