Roger MCX402-BRD User manual

MCX402-BRD Installation Manual.doc 2021-06-18
1/2
Roger Access Control System
MCX402-BRD Installation Manual
Firmware version: 1.1.0.302 and newer
Hardware version: 1.0
Document version: Rev. C
This document contains minimum information that is necessary for initial setup
and installation of the device. The detailed description of configuration
parameters and functionalities is specified in respective Operating Manual
available at www.roger.pl.
INTRODUCTION
The expander is designed to operate in RACS 5 system as peripheral device
connected to RS485 bus of MC16 access controller. Depending on uploaded
firmware the expander enables to control single door by MC16 controller using
two terminals with Wiegand interface or two PRT series terminals. MCX402-BRD
is installed in MCX402-1-KIT and MCX-402-2-KIT.
Factory new device is configured with default settings including ID=100 address.
Before connecting to MC16 controller, the device should be assigned with
unoccupied address in range of 100-115. Programming of other parameters
depends on the individual requirements and is not obligatory. Configuration of
the expander with RogerVDM requires RUD-1 interface.
CONFIGURATION WITH ROGERVDM PROGRAM
Fig. 1 Connection of the expander to RUD-1 interface
Programming procedure with RogerVDM software:
1. Connect the device to RUD-1 interface (fig. 1) and connect the RUD-1 to
computer’s USB port.
2. Start RogerVDM program, select MCX v1.x device, firmware version, RS485
communication channel and serial port with RUD-1 interface.
3. Click Connect, the program will establish connection and will automatically
display Configuration tab.
4. Enter unoccupied RS485 address in range of 100-115, enable Wiegand or
PRT terminals, configure input types (e.g. NC for IN5 according to fig. 5) and
other settings according to requirements of specific installation.
5. Click Send to Device to update the configuration of device.
6. Optionally make a backup by clicking Send to File… and saving settings to
file on disk.
Note: Time to connect to the device in RogerVDM is 30 seconds from power up.
In case of timeout, a power reset should be performed just before the
connection.
MANUAL ADDRESSING
The RS485 address of expander configured with RogerVDM is a software
address. Alternatively hardware RS485 address can be configured with jumpers
and such address has higher priority than software address.
Fig. 2 Manual addressing of expander
Note: Each time the hardware RS485 address is modified the device must be
restarted
MEMORY RESET
Memory reset procedure restores factory default settings including ID=100
software address.
Expander memory reset procedure:
1. Remove all connections from A, B, CLK and DTA terminals.
2. Place jumper on 64 contacts and restart device with RST button on device
board or by switching supply off and on.
3. Remove jumper from 64 contacts when LED STAT (red), LED OPN and LED
SYS are ON.
4. LED OPN and LED SYS will switch off and device shall restart automatically
with factory default settings.
FIRMWARE UPDATE
Factory new expander is equipped with a firmware dedicated to Wiegand
readers. If the expander is to be operated with PRT readers then another
firmware must be uploaded. Such firmware is available at www.roger.pl.
Firmware update requires RogerISP program.
Expander firmware update procedure:
1. Connect the device to RUD-1 interface (fig. 1) and connect the RUD-1 to
computer’s USB port.
2. Place jumper on FDM contacts
3. Restart device with RST button on device board or by switching supply off
and on.
4. Start RogerISP software.
5. Select serial port emulated by RUD-1 interface and the option USB-RS485
Converter.
6. Select firmware file (*.hex), click Program and follow instructions on screen.
7. Once the firmware is uploaded remove the FDM jumper and restart the
device.
8. Start Memory reset procedure.
APPENDIX
Fig. 3 MCX402-BRD expander
Table 1. Screw terminals
Name
Description
BAT+, BAT-
Backup battery

MCX402-BRD Installation Manual.doc 2021-06-18
2/2
P1
24VDC input power supply
P2
Ground
AUX
12VDC/1.0 output power supply (for door lock)
TML
12VDC/0.2A output power supply (for readers)
IN1-IN8
Input lines
GND
Ground
IO1, IO2
15VDC/1A transistor output lines
A, B
RS485 bus
CLK, DTA
RACS CLK/DTA bus
NO1, COM1, NC1
30V/1.5A DC/AC (REL1) relay
NO2, COM2, NC2
230V/5A AC (REL2) relay
Table 2 . LED indicators
Indicator
Colour
Integral function
AC
Red
AC power supply
STA
Red/ green
Current arming mode of Alarm Zone
(armed/disarmed)
OPN
Green
Door unlocked
SYS
Orange
Various signalling functions including errors
LINK
Green
Data transmission on RS485 bus
Fig. 5 Connection of readers and expanders to MC16 access controller
Table 3. Specification
Supply voltage
Nominal 18VAC, min./max. range 17-22VAC
Nominal 12VDC, min./max. range 10-15VDC
Nominal 24VDC, min./max. range 22-26VDC
Current consumption
(average)
100 mA (excluding load points connected to AUX
and/or TML outputs)
Battery charging current
300mA
Inputs
Eight (IN1..IN8) NO/NC inputs, triggering level
app. 3.5V
Relay outputs
Two (REL1,REL2) relay outputs with isolated
NO/NC contacts, 30V/1.5A (REL1) and
230VAC/5A (REL2) max. loads
Transistor outputs
Two (IO1, IO2) transistor outputs, max load
15VDC/1A
Power supply outputs
Two power outputs (AUX, TML), 12VDC/0.2A
(TML) and 12VDC/1A (AUX) max loads
Distances
Up to 1200 m between controller and expander
(RS485)
Up to 150m between expander and Wiegand or
PRT terminals
IP Code
IP20
Environmental class
(according to EN 50133-1)
Class I, indoor general conditions, temperature:
+5°C to +40°C, relative humidity: 10 to 95% (no
condensation)
Dimensions W x S x G
80 x 115 x 28mm
Weight
100g
Certificates
CE
Fig. 5 Typical door control with Wiegand readers
Fig. 6 Typical door control with PRT readers
By default the expander is uploaded with firmware for Wiegand readers. In
case of operation with PRT readers it is necessary to upload new firmware
from www.roger.pl.
In case of read-in door, single reader is connected to the expander.
Any 24VDC/1.5A PSU or 18VAC/40VA transformer can be used for expander
and door devices. In case of 12VDC PSU the backup battery cannot be
connected to the expander.
Any unoccupied IN1-IN8 inputs of the expander can be used for connection of
door contact and exit button.
Diagrams include doors with electric strikes. In case of electromagnetic lock,
the NC terminal of relay is used instead of NO terminal.
Diagrams includes exit buttons. In case of read-in/out doors they can be used
for emergency door opening.
This symbol placed on a product or packaging indicates that the
product should not be disposed of with other wastes as this may
have a negative impact on the environment and health. The user is
obliged to deliver equipment to the designated collection points of
electric and electronic waste. For detailed information on recycling,
contact your local authorities, waste disposal company or point of
purchase. Separate collection and recycling of this type of waste
contributes to the protection of the natural resources and is safe to
health and the environment. Weight of the equipment is specified in
the document.
Contact:
Roger Sp. z o. o. sp. k.
82-400 Sztum
Gościszewo 59
Tel.: [phone]
Fax: [phone]
Tech. support: [phone]
E-mail: [e-mail]
Web: www.roger.pl