Ropox Verti-Inside User manual

Ropox Verti-Inside
User Manual
Mounting Instructions
Service Manual
Keep this folder with the product at all times!
TF 200.0069_uk / Rev 002 / 12-09-2023
QR code to
mounting
video

TF 200.0069_uk / Rev 2 Page 2
Contents
1. INTRODUCTION .................................................................................................................................. 3
2. CONFORMITY WITH EU DIRECTIVE AND UK DIRECTIVE.............................................................. 3
3. APPLICATION...................................................................................................................................... 3
4. TECHNICAL DATA.............................................................................................................................. 4
5. DIMENSION SKETCH OF VERTI-INSIDE........................................................................................... 5
5.1 Construction see dimensions on the following page.................................................................. 5
5.2 Cupboard sizes........................................................................................................................... 6
5.3 Operation of Verti-Inside ............................................................................................................ 8
5.4 Wiring diagram ........................................................................................................................... 8
6. MOUNTING INSTRUCTIONS .............................................................................................................. 8
6.1 Mounting of accessories............................................................................................................... 17
7. PERFORMANCE TEST ..................................................................................................................... 18
8. LIST OF COMPONENTS, VERTI-INSIDE ......................................................................................... 19
9. OPTIONS, VERTI-INSIDE.................................................................................................................. 20
10. PLACING OF LED SPOT................................................................................................................... 22
11. CABLES FOR LED SPOT. ................................................................................................................ 23
12. SAFETY IN USE................................................................................................................................. 24
13. CLEANING/ MAINTENANCE ............................................................................................................ 25
13.1 Cleaning of frame..................................................................................................................... 25
13.2 Maintenance............................................................................................................................. 25
13.3 Service schedule, operation and maintenance ........................................................................ 26
14. FAULT FINDING ................................................................................................................................ 26
14.1 The frame cannot be adjusted in height (adjustment is very difficult)...................................... 26
15. LABEL............................................................................................................................................... 27
16. COMPLAINTS.................................................................................................................................... 27

TF 200.0069_uk / Rev 2 Page 3
1. Introduction
Verti-Inside is a wall cupboard unit for electrical height adjustment of wall cupboards.
Verti-Inside is ideal for wheelchair users or persons who are unable to reach the upper shelves
of the wall cupboards.
The users must follow these instructions. It is very important that the instructions have been
read and understood prior to operating the product.
These instructions must always be available to the user and must accompany the product in
case of relocation.
Correct use, operation and inspection are decisive factors for effective and safe performance.
2. Conformity with EU Directive and UK Directive
This product has CE marking according to the current Machinery Directive and is therefore in
accordance with the basic safety requirements.
This product has UKCA-marking and thus complies with the basic safety requirements.
If these frames are assembled or otherwise combined with other electrical components, the
assembly will be considered a new unit, which must be subjected to a risk assessment to obtain
CE marking.
3. Application
Verti-Inside is designed to obtain optimum working height for the user. Verti-Inside is designed
to adjust the height of wall cupboards. Verti-Inside must NOT be used as a lifting unit or person
lifter.
The product must be used indoor, under normal room temperature and humidity conditions as
stated in Section 4. Verti-Inside is not designed for use in damp rooms.
The control unit has protection IP32/ll and must always be installed in accordance with
the Danish High Voltage Regulations or corresponding national or international
standards.
This manual must ALWAYS accompany the product and be read by and available to the user
DO NOT use the system before reading section 12 “Safety in use” & after completing
section 7 “Performance test”
Make sure that ALL cables and connections are accessible at any time for
maintenance and servicing!!
This product is electrically height adjustable and the risk of trapping can occur.
Operation must always be carried out or supervised by an adult, who has read and
understood the importance of Section 12 “Safety in use”.
This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.

TF 200.0069_uk / Rev 2 Page 4
4. Technical data
Product name: Ropox Verti-Inside
Item numbers: Item number:
Verti-Inside width 40cm/15.7in, depth 26.5cm/10.4in: 30-40404
Verti-Inside width 50cm/19.7in, depth 26.5cm/10.4in: 30-40405
Verti-Inside width 60cm/23.6in, depth 26.5cm/10.4in: 30-40406
Verti-Inside width 70cm/27.5in, depth 26.5cm/10.4in: 30-40407
Verti-Inside width 80cm/31.5in, depth 26.5cm/10.4in: 30-40408
Verti-Inside width 90cm/35.4in, depth 26.5cm/10.4in: 30-40409
Verti-Inside width 100cm/39.4in, depth 26.5cm/10.4in: 30-40410
Verti-Inside width 40cm/15.7in, depth 31cm/12.2in: 30-40414
Verti-Inside width 50cm/19.7in, depth 31cm/12.2in: 30-40415
Verti-Inside width 60cm/23.6in, depth 31cm/12.2in: 30-40416
Verti-Inside width 70cm/27.5in, depth 31cm/12.2in: 30-40417
Verti-Inside width 80cm/31.5in, depth 31cm/12.2in: 30-40418
Verti-Inside width 90cm/35.4in, depth 31cm/12.2in: 30-40419
Verti-Inside width 100cm/39.4in, depth 31cm/12.2in: 30-40420
Material: Welded steel pipes St. 37 and various plastic components
Surface treatment: Blue chromate, powder coating
Power supply: 220-230V~ / 50-60Hz, 5,0A
Standby primary: <0.3W
Control voltage: 24VDC
Duty cycle max.: Max. 2 min. active then 18 min. pause
Max. load: 80kg / 175lb evenly distributed
Speed/time for lifting: Approx. 33 mm/sec. –Approx. 15 sec.
Travel 495mm / 19.4in
Temperature: 5-45° C
Air humidity: 5-85% (non-condensing)
Complaints: See Complaints page 28
Manufacturer: Ropox A/S, DK-4700 Næstved, Tel.: [phone]
e-mail: in[email protected] - www.ropox.dk

TF 200.0069_uk / Rev 2 Page 5
5. Dimension sketch of Verti-Inside
It is important that cables to the control unit are flexible and can move freely within the height
adjustment range of the unit.
Travel: 495mm/19.4in
The cupboard is mounted on the wall
with min. 530mm/20.8in between the
bottom of the cupboard and other
installations for utilisation of the entire
travel of the unit
703mm / 27.6in
350/450/550/650/750/850/950mm
iincrementsval
Depth 265mm or 310mm
Depth 10.4in or 12.2in
13.7/17.7/21.6/25.6/29.5/33.4/37.4 in
495mm/19.4in

TF 200.0069_uk / Rev 2 Page 6
5.1 Construction see dimensions on the following page
Minimum area for reinforcement of wall. Wall material must be suitable for screw
mounting.
Area for electric installation.
Area for conduit.
Cabinet height of 70.4cm/27.7in or more. For cabinet heights above 70.4cm/27.7in a fixed shelf
is placed in the upper part of the cabinet (see illustration).
Cable for operation must be laid from the cabinet to the front edge of the worktop for mounting
of the control switch. We recommend the installation of an empty conduit in the wall to
accommodate the cable (ø3.5cm).
If a high cabinet stands in the immediate vicinity of Verti-Inside, the cable may be run through
the cabinet to avoid the conduit in the wall.
Max. load 80kg/175lb evenly distributed over all three shelves for cabinets up to 100cm/39.4in
in width, according to DS/EN 12182, based on 8 screws/bolts.
Minimum load capacity per screw/bolt:
10.5kg / 23lb
The fitter should always consider the material, condition and strength of the wall and use screws
and rawlplugs suitable for the specific wall type.
5.2 Cupboard sizes
704mm/27.7in, higher cupboards may be used

TF 200.0069_uk / Rev 2 Page 7
Cabinet height of 70.4 cm / 27.7 in
Cabinet height above 70.4 cm / 27.7in
Fixed shelf for mounting
the top safety stop
electric
installation
electric
installation

TF 200.0069_uk / Rev 2 Page 8
5.3 Operation of Verti-Inside
The height of the cupboard is adjusted by means of the
control switch connected to the control unit.
The cupboard is adjusted upwards by pressing the UP
symbol of the control switch and downwards by pressing the
DOWN symbol of the control switch.
As soon as you let go of the control switch, the movement
of the unit will stop.
5.4 Wiring diagram
S2
S1
HS
M1

TF 200.0069_uk / Rev 2 Page 9
6. Mounting instructions
Before starting installation, check that all parts mentioned in the list of components have been
delivered.
See list of components, Section 8.
Mounting must always be carried out by competent personnel
Mount 2 x 30-40400-021
flush with rear edge of cupboard
Remove back and bottom from the cupboard.
Note!
The back may remain in place if it is fastened to
the wall by bolts
Mount cupboard on wall
Drill 1 x Ø40mm/1.6in hole in the
top of the cupboard for cables
Mark up for upper safety stop (see
9)
14 x Ø3.5mm/0.1in x12
wood screw
1
2
3
4
70mm/2.7in from center
Wall
/ 1in

TF 200.0069_uk / Rev 2 Page 10
Lift lifting unit 30-40400-042 into the cupboard
and hook it onto the suspension fixture
Drill holes in wall. Fasten lifting unit
30-40400-042 with 7 screws. Use
screws and lplugs suiting the
construction and materials of the
wall
5
6
7
Mount suspension fixture 30-40400-019 on wall
*When installing the verti-Inside
in a cabinet height of 704 mm /
27.7 in the safety stop will be
20mm/0,8in lower than the
cabinet.
20mm/0.8in
2.1in
27.7in

TF 200.0069_uk / Rev 2 Page 11
1. Connect the control switch to HS
If required, use extension cord: 93000162
Pull the cable behind the motor and
through the hole at the top of the
cupboard
2. Pull mains cable behind the motor and
through the hole at the top of the
cupboard, connect and turn on power
3. Connect the motor cable 96000814 to M1
8
M1
HS
Mains cable

TF 200.0069_uk / Rev 2 Page 12
Monting of top safety stop
Connect safety stop to control unit, to
the cable marked: S1.
(See wiring diagram page 8)
Mount upper safety stop on top of the
cupboard. (Illustration shows cupboard
viewed from below)
Wall
=
=
22mm
/
9
10
4 x Ø5x20
wood screw
4 x 96121409,
plastic bushing
/ 0.8in

TF 200.0069_uk / Rev 2 Page 13
Mount cover plate 30-40400-085
The top of the cover plate has
“keyholes” fitting the pre-mounted
bolts of the lifting unit
The bottom of the cover plate has a flange
fitting around the lifting unit.
When the ”keyhole” and flange “catch”, push
the plate upward and tighten the bolts.
11

TF 200.0069_uk / Rev 2 Page 14
12
Lift front plate into the cupboard and hook it onto
the pre-mounted bolts of the lifting unit. Now
mount the remaining 6 bolts
6 x M6x10

TF 200.0069_uk / Rev 2 Page 15
1
2
1
2
4
Connect safety stop and spiral cable
Mount cable relief for mains cable on wall
13

TF 200.0069_uk / Rev 2 Page 16
Mount 97701-841 and 97701-842 shielding for control switch
1
1
14
2 x M3x8
Place control switch acc. to customer’s wish
and connect by means of cable: 97000245.
If required, use extension cord: 93000162

TF 200.0069_uk / Rev 2 Page 17
6.1 Mounting of accessories
6.1.1 Mounting the Bluetooth Adapter for Ropox Connect App
6.1.2 Downloading the Ropox Connect App
As an option to operate certain Ropox products, it’s possible to download the free Ropox Connect App,
which makes it possible to operate the product wirelessly. The Ropox Connect App allows you to operate
the product upwards or downwards and has the option of saving height settings, allowing users to easily
change from a standing height to a sitting height. To see an expanded explanation of functions,
accessibility settings, and more, see the enclosed manual, TF 200.0054.
To download the Ropox Connect App, follow the instructions below:
How to download the Ropox Connect App
For iOS
1. Scan the QR code or open the app: App Store.
2. In the App Store, press ‘Search’.
3. Search for ”Ropox Connect”.
4. Find the Ropox Connect App, and press ‘Get’.
6.1.1.1 Determine the placement of the
adapter, then grab the Bluetooth
adapter and the split-cable
6.1.1.2 Insert the split-cable in the plug ”HS”
in the control box. Then, insert the
adapter in one end of the split
cable, and the button that came with
the product, in the other
6.1.1.3 If the adapter is to be fixed, it should
be done now

TF 200.0069_uk / Rev 2 Page 18
7.Performance test
After completed installation and before use all functions of the module must be tested. After that
a performance test must be carried out at least once a year by competent personnel.
1. Check that the mounting instructions have been observed.
2. Check that all bolts and screws have been tightened.
3. Check that all cables have been correctly connected and that the plugs have been pressed
all the way in
4. There must be no load on the unit.
5. There must be no objects preventing the frame from moving freely within the range of height
adjustment.
Start-up procedure
1. Connect the net cable and turn on the power
2. Connect the motor cables to M1
3. Connect the control switch to HS
4. Press UP on the control switch, move the frame to top position, check that the movement is
even and smooth. The frame is now reset.
5. Press DOWN on the control switch, move the frame to bottom position and check that the
movement is even and smooth.
The safety stops must be tested:
Lower safety stop: Press the DOWN button and let the cupboard move 2-5cm/0.8-1.9in
downwards and activate the safety stop. The unit must now stop the downward movement,
move 1-2cm/0.4-0.8in upward and stop.
Upper safety stop: Press the UP button and let the cupboard move 2-5cm/0.8-1.9in upwards
and activate the safety stop. The unit must now stop the upward movement, move 1-2cm/0.4-
0.8in downwards and stop.
When all these tests have been carried out successfully, the unit is ready for use.
See ”Safety in use” Section 11.

TF 200.0069_uk / Rev 2 Page 19
8. List of components, Verti-Inside
Item number
Designation
Number
Illustration
30-40400-453
30-40400-019
30-40601-144
96000169
95010416
Verti-InsideElectric
Lifting unit
Suspension fixture
Relief for mains cable
Cable clips 24mm/1in
M4x16 bolt, cylindrical head
1 (one)
1 (one)
1 (one)
1 (one)
2 (two)
30-40400-085
Cover plate
1 (one)
Mains cable 300cm/118.1in
1 (one)
30-67840
93000162
Control switch standard, (3x6 cm)
1 (one)
incl. 150cm/59in cable
Extension cord for control switch
3.5m/137.8in
1 (one)
98002087
Spiral cable male/female
1 (one)
30-40400-113 (40cm)
30-40400-114 (50cm)
30-40400-115 (60cm)
30-40400-116 (70cm)
30-40400-117 (80cm)
30-40400-118 (90cm)
30-40400-119 (100cm)
Front plate
1 (one)
30-40204-2 (40cm)
30-40205-2 (50cm)
30-40206-2 (60cm)
30-40207-2 (70cm)
30-40208-2 (80cm)
30-40209-2 (90cm)
30-40210-2 (100cm)
Safety stop bottom, for 26.5cm/10.4in
cupboard
1 (one)
30-40214-2 (40cm)
30-40215-2 (50cm)
30-40216-2 (60cm)
30-40217-2 (70cm)
30-40218-2 (80cm)
30-40219-2 (90cm)
30-40220-2 (100cm)
Safety stop bottom, for 31cm/12.2in
cupboard
1 (one)
30-40304-1 (40cm)
30-40305-1 (50cm)
30-40306-1 (60cm)
30-40307-1 (70cm)
Safety stop top, for 26.5cm/10.4in
cupboard
1 (one)

TF 200.0069_uk / Rev 2 Page 20
30-40308-1 (80cm)
30-40309-1 (90cm)
30-40310-1 (100cm)
30-40314-1 (40cm)
30-40315-1 (50cm)
30-40316-1 (60cm)
30-40317-1 (70cm)
30-40318-1 (80cm)
30-40319-1 (90cm)
30-40320-1 (100cm)
Safety stop top, for 31cm/12.2in
cupboard
1 (one)
95122516
Chip board screw 3.5x16
14 (fourteen)
95010008
M6x10 bolt, button head
8 (eight)
95020616
M6x16 countersunk bolt
4 (four)
96121409
Sleeve bushing
4 (four)
30-40601-097
Distance washer
4 (four)
97701-841
Shielding for control switch part 1
1 (one)
97701-842
Shielding for control switch part 2
1 (one)
9. Options, Verti-Inside
Split cable for control switch 96000629: 1 (one)
To be used if more than one control switch is required
Control switch, large press pad (14x7 cm) 30-67841:
Disabled press pad incl. 150 cm/59in cable 1 (one)
Control switch 40-14701-9:
Control switch with spiral cable 1 (one)
Smartbox 30-69002-1: 1 pc.
Option for safety stop plate
To be ordered if Diagonal is mounted above a FlexiElectric
Ropox connect app 30-90591:
Remote control with app 1 pc.