RTA Products RTA-B002 User manual

Sit-to-Stand Rolling Adjustable
Height Laptop Cart With Storage
MODEL RTA-B002
ASSEMBLY INSTRUCTIONS
REV.OL-7284-0423
Thank you for purchasing our product
Scan QR to view full
assembly video
VIDEO
Scan QR to view the
manual in French
FRENCH
Scan QR to view the
manual in Arabic
ARABIC

Replacement Parts for International Customers &
AK-HI-PR orders:
RTA Products will replace the part free of charge,
while the customer is responsible for shipping
costs plus any International local taxes or duties.
Do a quick inventory
of all the parts and
hardware listed below.
Support & Replacement
Parts for the 48 contiguous
United States:
Please email us at:
[email protected]
(top surface)
(bottom surface)
(top surface)
P.1 P.1
RTA-B002
1
x1
2
x1
3L
x2
4
x1
Left panel Right panel Locking caster Back panel
MAIN PARTS LIST
5
x1
6
x1
7
x1
8
x1
Front panel Middle shelf Bottom panel Top shelf
9
x2
10
x2
Stationary tube Adjustable “T”
tube
11A
x2
12
x1
Plastic
square cover
Main panel
3N
x2
Non-locking caster
11B
x2
Screw knob
13
x1
Top protection tube
MAIN PARTS LAYOUT (FOR
REFERENCE):
1
9
12
13
2
5
6
7
8
3L
11B
10 11A
PART
QTY ITEM
A16 M4x14
B2M6x25
C10 M6x35
D22 M6x40 Bolt
1Screwdriver
SCREWS LIST AND INCLUDED TOOLS

P.2 P.2
RTA-B002
BEFORE YOU START THE ASSEMBLY, PLEASE READ THE FOLLOWING TIPS AND WARNINGS.
M6
30mm
M6x30
• Make sure you understand which
hardware will be used on each step. Using
the wrong size of screw, bolt or pin might
strip the threads or cause damage to the
part in which it is being used.
• To avoid misalignments, always leave the screws
loosely and do not tighten them until all the pieces
are positioned correctly.
• Do not overtighten or force the screws as they might
break, strip, damage the threads of the holes, or get
stuck inside the parts.
• If the hole seems to small for the screw, make sure
you are using the correct size of screw and/or that
you are installing it in the correct hole.
• Sometimes on the wood panels the laminate or
material might be covering the hole partially or
entirely, if there is no visible hole or if it looks too
small, pass and press the tip of your finger over the
area to feel its indentation, and carefully pierce the
laminate to uncover the hole underneath.
√
√
• Please read the assembly instructions throughly and
follow step by step.
• After the item is assembled, you can use rubbing
alcohol to erase or remove the visible part
numbers printed or labeled on the pieces.

RTA-B002
P.3 P.3
1. Screw the bolt into the indicated hole on the
panel indicated in the assembly step.
CAM BOLT AND CAM LOCK TUTORIAL
THE INSTRUCTIONS BELOW
ARE NOT ACTUAL ASSEMBLY STEPS
This unit uses cam bolts and locks (also known as mini fixes).
If you are not familiar with this kind of hardware, the below is a tutorial
that explains how to use them on the steps where they are required.
2. Join the other panel (with the big hole) to the
panel with the bolt. If it comes with the cam
locks already pre-installed, make sure to align
them to receive the bolt's head (refer to point
3). There might be a very small gap between
the panels which is normal.
3. Insert the cam lock on the panel with the big
hole making sure it goes aligned to receive the
bolt's head.
4. Use a Phillips screwdriver to turn the cam
lock clockwise. This will lock the panels
togheter and also will close any gaps.
Cam lock
alignment
If the cam locks come
pre-in stalled, make sure they
are aligned (see point 3).
THE ASSEMBLY STEPS START ON NEXT PAGE
THIS IS ONLY
A TUTORIAL
THIS IS ONLY
A TUTORIAL
THIS IS ONLY
A TUTORIAL
THIS IS ONLY
A TUTORIAL

Cam lock
alignment
WE RECOMMEND TO PLACE THE PIECES OVER BLANKETS TO PROTECT THEIR
FINISH DURING ASSEMBLY.
RTA-B002
P.4 P.4
ASSEMBLY STEPS
• Attach bolts Dinto the indicated holes on the left panel 1.
•
•
On panels 4, 5 and 6 check and make sure the cam locks on their left
side are aligned to receive the bolts.
Assemble the panels 4, 5 and 6 to panel 1 and turn the cam locks to
lock the panels as explained in page 3. Note: Panels 4and 6do not
assemble one another, they just lay flushed.
STEP 1
Hardware:
DM6x40
Bolt
5
Pcs
Screw bolts D into the corresponding holes on the right panel 2, then
align cam locks on panels 4, 5, 6 and finally assemble panel 2 to those
panels and turn the cam locks as explained in page 3.
4
1
(Bottom)
(Top)
(Bottom)
STEP 2
Hardware:
DM6x40
Bolt
5
Pcs
6
5
Cam lock
alignment
4
2
6
5
Surface with cam
locks on 6 must face
towards the bottom
Surface with cam l
ocks
on 4and 5must face
towards the interior
(Front)
(Top)

RTA-B002
P.5 P.5
Use screws Ato assemble the casters 3to panel 7to its bottom surface
the following way:
Assemble the panels 1,2and 4(from step 2) to the top surface of panel
7with bolts Das explained in page 3. Please make sure to identify the
correct holes where Dwill be installed on the bottom panel.
(Front)
STEP 3
Hardware:
A
M4x14
16
Pcs
STEP 4
Hardware:
DM6x40
Bolt
6
Pcs
7
3L
2
1
Cam lock
alignment
• Locking casters 3L go at the front of the panel.
• Non-Locking casters 3N go at the back of the panel.
LOCKING
go at the front
of the panel ,
with lock facing
towards the front
3N
7
(Front)
NON-LOCKING
go at the back
4

RTA-B002
P.6 P.6
Assemble the top shelf 8to panels 1,2and 4with bolts Das explained
in page 3.
Assemble the stationary tubes 9to the side panels 1and 2with screws
Cfrom the sides and to the bottom panel 7from the bottom.
STEP 5
Hardware:
DM6x40
Bolt
6
Pcs
STEP 6
Hardware:
C
M6x35
6
Pcs
2
1
2
1
Cam lock
alignment
8
4
9
7
9

RTA-B002
P.7 P.7
Place the plastic covers 11A over the tubes 9with their threaded
holes facing towards the outside.
• Insert the adjustable “T” tubes 10 through the covers 11A and into the
tubes 9making sure the longer end of the square tubes faces towards
the front.
• Lift the tubes at least 7 inches (about an open hands’ width) and insert
and tighten the screw knobs 11B into the covers 11A.
• Both tubes should be lifted at the same height to be able to do the
next step properly.
Hole facing
towards the
outside
Longer end towards the front
(Lift at least 7")
(Insert 11B into
11A and tighten)
FIRST:
STEP 7
STEP 8
9
9
11A
10
10
11B
11B
11A
11A
11A
THEN:
11A

RTA-B002
P.8 P.8
Assemble the main panel 12 to the tubes 10 with screws Cfrom
underneath.
Assemble the protection tube 13 to the main panel 12 with screws B
from underneath.
(Front)
(Front)
STEP 9
Hardware:
C
M6x35
4
Pcs
STEP 10
Hardware:
B
M6x25
2
Pcs
10
12
13
10
12

RTA-B002
P.9 P.9
STEP 11
11B
11B
LIFTING: Loosen the screw knobs 11B to lift, then tighten again.
• If you have objects or devices on or
under the main panel, use caution
when adjusting the height.
• Do not overtighten the screw knobs.
• Do not use the unit if the plastic
covers look cracked or if the screw
knobs are stripped.
ROLLING: Unlock the front casters to allow free movement.
• Before moving the unit, unlock the
front casters and secure or remove
any object that might fall off while the
unit is rolling.