RTA Products Techni Mobili RTA-B018 User manual

Thank you for purchasing our product.
MODEL RTA-B018
ASSEMBLY INSTRUCTIONS
REV.032021-2

•Please read carefully the assembly instructions
before the installation.
•Do not discard this manual or any of the packaging
material until the unit has been completely
assembled.
•Might require two people.
P. 1 RTA-B018 P. 1

8
x1
5
x1
4
x1
1
x1
2
x1
3
x1
Drawer back panel Drawer right panel Drawer bottom panel Drawer left panel
MAIN PARTS LIST
6
x1
Drawer front panel Left frame Right frame Back panel
10
x1
Bottom panel Middle panel 11
x1
Main panel
LIST OF HARDWARE
PART
QTY ITEM
A10 M5x60
B2Cam Lock
C2Cam Bolt
D2Caster
E2Caster W/Lock
F8M6x30
G4ST4x12
H4M4x8
Tools
P. 2 RTA-B018 P. 2
7
x1
9
x1
12
x2
Slider
MAIN PARTS LAYOUT
(FOR REFERENCE):
11
10
8
DE
9
67

P. 3 RTA-B018 P. 3
☛This unit uses cam bolts and locks. The following explains how to use them.
This is not an assembly step; it is a guide for when you are actually doing the
assembly using this kind of hardware.
Cam Bolt Cam Lock
1. Screw the bolt into the
corresponding panel.
2. Place the other panel over the
panel with the bolt, then insert the
cam lock to join the bolt’s head.
If the cam lock does not want to
enter, check its proper alignment.
There might be a very small gap
between the panels which is normal.
3. Turn the cam lock clockwise. This
will lock the parts together and will
close any gaps.
Alignment: The cross
points towards the panel
with the bolt.

BEFORE YOU START THE ASSEMBLY, PLEASE READ THE FOLLOWING TIPS AND WARNINGS.
❶Do aquick inventory
to make sure the package
contains all the parts and
hardware listed in the
assembly instructions.
❷Missing, damaged
and defective parts can
be replaced at no cost
to you. Please refer to
the last pages on this
manual.
❸The replacement parts
service is limited to the
continental United States.If
you reside in Hawaii, Puerto
Rico, U.S. Dependencies or
other countries, please
contact the supplier from
where the unit was
purchased.
❹If during assembly
you find an issue or
need clarification, please
contact our Customer
Service for assistance.
Please refer to the last
pages on this manual.
❺On each step read the
instructions and analyze
the illustrations thoroughly
before proceeding to do the
assembly.
❽Do not overtighten
or force the screws as
they might break, strip,
damage the threads of
the holes or get stuck
inside the part.
❻Make sure you
understand which
hardware will be used on
each step.Using the
wrong size of screw, bolt
or pin might strip the
threads or cause damage
to the part in which it is
being used.
❼To avoid
misalignments, always
leave the screws loose
and tighten them until
all pieces are
positioned correctly.
❾Sometimes the laminate might cover
partially or entirely the hole on apanel.If there
is no visible hole for the screw, pass and press
the tip of your finger over the area where the
hole should be located to feel the indentation,
and once found, carefully pierce the laminate to
reveal the hole underneath.
❿If the hole seems too small for the screw,
first make sure you are using the correct size of
screw and that it’s been installed in the correct
hole.If the hole still appears to be too small,
carefully pierce the laminate to reveal the
hole’s actual size.
P. 4 RTA-B018 P. 4

ASSEMBLY STEPS
Insert the bolts Cinto panel 5,then join it to panels 2and 4.Insert the
cam locks Band turn them to lock the panels as shown and as
explained in page 3.Then insert the panel 3through the grooves of all
the panels, and finally, assemble the back panel 1to the side panels 2
and 4with screws Aas shown.
P. 5 RTA-B018 P. 5
Open the sliders 12 and attach them to the top bars of the left frame 6
and the right frame 7with screws Hfrom the inside.Then assemble the
casters to the bottom of the frame, making sure the non-locking casters
Dgo at the back,and the locking casters Ego at the front of the unit.
STEP 2
Screws/Tools:
D
Non-
Locking
2
Pcs
E
Locking
2
Pcs
H
M4x8
4
pcs
STEP 1
Screws/Tools:
A
M5x60
2
Pcs
B
Cam Lock
2
Pcs
C
Cam Bolt
2
Pcs
Cam lock
alignment
NON-LOCKING AT BACK LOCKING AT FRONT

P. 6 RTA-B018 P. 6
Assemble the back panel 8and the bottom panel 9to both frames with
screws Afrom the outside as shown.
STEP 3
Screws/Tools:
A
M5x60
8
Pcs
Attach the middle panel 10 to the middle bars on the frames with
screws Ffrom underneath.
STEP 4
Screws/Tools:
F
M6x30
4
Pcs

P. 7 RTA-B018 P. 7
STEP 5
Screws/Tools:
F
M6x30
4
Pcs
Place the main panel 11 over the frames and secure it with screws F
from underneath.
STEP 6
Screws/Tools:
G
ST4x12
4
Pcs
Pull out the sliders and attach to them the utility drawer with screws G.

ALL DONE!
Give yourself a nice pat on the back. You did a great job!
P. 8 RTA-B018 P. 8

AFTER THE ASSEMBLY IS DONE, PLEASE READ CAREFULLY THE FOLLOWING
CARE AND MAINTENANCE WARNINGS:
•Do not exceed the indicated weight limits.
•Do not expose the surfaces to direct sunlight or to extreme environmental conditions.
•Clean the surfaces preferable with a clean cloth damped in a solution of mild soap and
water, then dry with a clean towel.
•Do not use solvents or abrasive materials to clean the unit.
•If you decide to use a cleaning agent, test first on an area hidden from view such as
underneath the tabletop.
•Do not sit on the unit or lean against it.
•Do not allow small children to play under or over the unit, nor use it as a moving
vehicle.
•Keep the unit with the front casters locked.
•Before moving the unit, make sure to unlock the front casters, and secure or remove
any object that might fall off.
•When lifting the unit, use both hands and bend your knees, not your backs.
•When transporting the unit to places far away, lock the front casters and protect and
secure the unit to avoid damage in transit.
•Shall any part of the unit become defective during the warranty period, replacement
parts might be available to you at no charge. Please refer to the last pages on this
manual.
•The warranty does not extend to regular wear and tear, nor the manufacturer assumes
liability for damages or consequences due to accidents, incorrect assembly,
negligence, improper use, modifications, or not heeding the above warnings.
WEIGHT LIMITS
P. 9 RTA-B018 P. 9
90 Lbs
(40.82 Kg)
10 Lbs
(4.53 Kg)
90 Lbs
(40.82 Kg)
70 Lbs
(31.75 Kg)

RTA Products, LLC warrants to the Original Purchaser who acquired anew product from
RTA Products or its authorized resellers that this product will be free from defects in its
workmanship and materials, under normal use and service conditions, as described
herein."Defects" as used in this warranty, is defined as any imperfections that impair the
use of the furniture or product.RTA Products LLC will replace any defective part, at its
discretion, and without charge to the original purchaser other than the freight from the end
consumer to RTA Products.
Replacement parts can only be supplied if parts are available.Items out of production
may be unavailable.This warranty will be effective for the applicable time period
beginning the date of purchase on your original sales receipt.RTA product’s obligation
under this warranty is limited to repairing or replacing products or parts as provided
herein.This product has been designed for and is intended for office and home-office use
only.This warranty is Original Purchaser’s sole remedy for product defects, and this
warranty does not extend to any product, or damage to any product, caused by or
attributed to abuse or misuse, products used for commercial or rental purposes, use
modifications of, or attachments to the product, and products or parts not used,
maintained, or extended hereunder is in lieu of any and all other warranties, express or
implied, including without limitations any implied warranty or merchantability or of fitness
for aparticular purpose.Please note, all desks made with PVC Laminate surface should
not be exposed to direct sunlight, as it may damage the material.Damage of this nature
is not covered under this warranty.
RTA Products will not be responsible for indirect, special, incidental or consequential
damages.This warranty is limited to merchandise purchased in the Continental United
States.Some States do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitations or exclusions may not apply to you.This warranty
gives you specific legal rights.You may also have other rights that may vary from state to
state.
RTA Products will advise you of the procedure to follow in making warranty claims.The
following are the procedures for warranty claims:
a. Call us Monday –Friday, from 9am-5pm (Eastern Time) at [phone] to explain
the defect and give your name, address and phone number.Please have ready the
model number of our product, date and place of purchase.You can also write to us by
e-mail to [e-mail] and include the same information.
b. If we determine that replacement will remedy the situation, and in order to determine
the extent or the cause of the defect, purchaser will need to send the part in question
at purchaser’s expense.Once we receive the part, we will examine it and determine
whether the claim is valid (or not), and then proceed to send the replacement.We will
ship the replacement at our expense.
P. 1 0 RTA-B018 P. 1 0
TECHNI MOBILI WARRANTY
DESKS/LAPTOP CARTS/FILE CABINETS: LIMITED 5-YEAR WARRANTY
TV Stand/Entertainment Center: 2 YEAR WARRANTY

FOR SEVERAL HELP OPTIONS
INCLUDING REPLACEMENT PARTS ORDERS
_________________________________________________________________
VISIT: WWW.TECHNIMOBILI.COM
CLICK ON SUPPORT TAB
Scan QR Code to order replacement parts
OR EMAIL US: [e-mail]
P. 11 RTA-B018 P. 11