RTA Products Techni Mobili RTA-9500TV User manual

Thank you for purchasing our product.
MODEL RTA-9500TV
ASSEMBLY INSTRUCTIONS
REV.082021-0

•Please read carefully the assembly instructions
before the installation.
•Do not discard this manual or any of the packaging
material until the unit has been completely
assembled.
•Might require two people.
P. 1 RTA-9500TV P. 1

P. 2 RTA-9500TV P. 2
1
x1
2
x1
Bottom panel Top panel
MAIN PARTS LIST
3
x1
4
x1
5
x1
6
x1
Left panel Right panel Middle-Left panel Middle-Right panel
7
x1
Middle panel 8
x3
9
x2
Shelves Sliding door
10
x1
Top front panel 11
x2
Back panel

MAIN PARTS LAYOUT (FOR REFERENCE):
P. 3 RTA-9500TV P. 3
LIST OF HARDWARE, SCREWS AND FITTINGS
PART
QTY ITEM
A32 M8x30
Dowels
B22 Bolts
C22 Cam locks
D8ST3.5x14
E10 ST4x50
F12 ST3.5x25
G80 Nails
PART
QTY ITEM
H4Bracket
I8Plastic pin
J22 Covers
K6Feet
L4Sliding
tracks
M2Grommet
(Handle)
1Touch-up
chalk
NOTE: You will need for the assembly a Phillips screwdriver and mallet/hammer (not
included).
05
07 06
03 04
11
11
11
08
08
08
10
09 09
01
02

P. 4 RTA-9500TV P. 4
☛
☛
This unit uses cam bolts and locks. The following explains how to use them.
☛
☛
This unit uses cam bolts and locks. The following explains how to use them.
This unit uses cam bolts and locks. The following explains how to use them.
This is not an assembly step; it is a guide for when you are actually doing the
This is not an assembly step; it is a guide for when you are actually doing the
assembly using this kind of hardware.
Cam Bolt
Cam Lock
1. Screw the bolt into the corresponding hole
on panel “A”.
3. Insert the cam lock on panel “B” making
sure it goes aligned to receive the bolt’s head.
4. Turn the cam lock clockwise. This will lock the
parts together and will close any gaps.
Alignment: The cross points
towards the panel “A” with the bolt.
2. Join panel “B” to panel “A”. If panel “B” comes
with the cam lock pre-installed, make sure it is
aligned to receive the bolt’s head (refer to point
3). There might be a very small gap between the
panels which is normal.
Panel “B”
Panel “B”
Panel “B”
Panel “B”
Panel
“B”

BEFORE YOU START THE ASSEMBLY, PLEASE READ THE FOLLOWING TIPS AND WARNINGS.
❶Do aquick inventory
to make sure the package
contains all the parts and
hardware listed in the
assembly instructions.
❷Missing, damaged
and defective parts can
be replaced at no cost
to you. Please refer to
the last pages on this
manual.
❹If during assembly
you find an issue or
need clarification, please
contact our Customer
Service for assistance.
Please refer to the last
pages on this manual.
❺On each step read the
instructions and analyze
the illustrations thoroughly
before proceeding to do the
assembly.
❽Do not overtighten
or force the screws as
they might break, strip,
damage the threads of
the holes or get stuck
inside the part.
❻Make sure you
understand which
hardware will be used on
each step.Using the
wrong size of screw, bolt
or pin might strip the
threads or cause damage
to the part in which it is
being used.
❼To avoid
misalignments, always
leave the screws loose
and tighten them until
all pieces are
positioned correctly.
❾Sometimes the laminate might cover
partially or entirely the hole on apanel.If there
is no visible hole for the screw, pass and press
the tip of your finger over the area where the
hole should be located to feel the indentation,
and once found, carefully pierce the laminate to
reveal the hole underneath.
❿If the hole seems too small for the screw,
first make sure you are using the correct size of
screw and that it’s been installed in the correct
hole.If the hole still appears to be too small,
carefully pierce the laminate to reveal the
hole’s actual size.
P. 5 RTA-9500TV P. 5
❸The replacement parts
service is limited to the
48 contiguous United States.
If you reside in Alaska,
Hawaii, Puerto Rico,
U.S. territories or other
countries, please contact the
supplier from where the unit
was purchased.

ASSEMBLY STEPS (Note: the unit will start assembling with its front facing down)
•Install bolts B in the indicated holes on the faces of panels 2, 5, 6 & 7.
•Note 1: Other holes are intended for other kind of hardware.
•Note 2: On panel 7, the bolt is installed on both faces.
STEP 2
Hardware:
B
M6x20
22
Pcs
(NOT INCLUDED)
P. 6 RTA-9500TV P. 6
On panel 7, the bolt is
installed on both faces.
5
2
6
7
•
•
Install brackets H into the groove of panel 10 with screws D. If there
are no pre-drilled holes or markings, just calculate a good distance
between them, but you must leave at least 1” space from each end.
Install the sliding tracks L on the bottom panel 1 and the Top panel 2.
STEP 1
Hardware:
D
ST3.5x14
4
Pcs
H4
Pcs
L4
Pcs
(NOT INCLUDED)
1
2
1
10
L
H
D
(Top)
(Bottom)
Leave at least 1"
space at each end

P. 7 RTA-9500TV P. 7
•Join the panels 6and 7to two of the panels 8, then install the cam
locks Cand turn them to locks the pieces as explained in page 4.
•Note: The panels 8must have their smooth faces towards the TOP.
STEP 4
Hardware:
C
Cam lock
8
Pcs
(NOT INCLUDED)
7
8
Please refer to page 4
(Top)
(Bottom)
6
8
Install the wooden dowels Ainto the indicated holes on the profiles of
panels 3, 4, 5, 6, 7and 8.
STEP 3
Hardware:
A
M6x20
32
Pcs
(NOT INCLUDED)
8
7
4
3
6
8
8
5

P. 8 RTA-9500TV P. 8
With the help of another person, join the top panel 2to panels 5, 6and 7,
then install the cam locks Cand turn them to lock the pieces as
explained in page 4.
STEP 6
Hardware:
C
Cam lock
6
Pcs
(NOT INCLUDED)
7
6
The grooves on 2 go
facing DOWN towards
the FRONT of the unit
Cam locks alignment
5
2
•Join the panels 5and 7to the third panel 8, then install the cam locks
Cand turn them to locks the pieces as explained in page 4.
•Note: The panel 8must have its smooth face towards the TOP.
STEP 5
Hardware:
C
Cam lock
4
Pcs
(NOT INCLUDED)
5
7
(Top)
(Bottom)
8

P. 9 RTA-9500TV P. 9
Install the plastic pins Iand the grommets Minto the doors 9. Please
note the orientation of the pins, as they will enter and glide into the
grooves of panel 2in the next step.
STEP 8
Hardware:
I8
Pcs
M2
pcs
M
9
I
9
Join panels 3and 4to panel 2, then install the cam locks Cand turn
them to lock the pieces as explained in page 4.
STEP 7
Hardware:
C
Cam lock
4
Pcs
(NOT INCLUDED)
4
3
Cam locks alignment
2
0206