RTA Products Techni Mobili RTA-3800SU User manual

By
Thank you for purchasing one of our products.
Please read carefully the assembly instructions before the installation.
Do not discard this manual or any of the packaging material until the unit
has been completely assembled.
MODEL RTA-3800SU
ASSEMBLY INSTRUCTIONS

P. 2 RTA-3800SU P. 2
❶
x1
❷
x1
❸
x2
❹
x1
Back tabletop Front tabletop Metal leg Back structure
MAIN PARTS LIST
HARDWARE
❺
x1
❻
x1
❼
x2
❽
x2
Front structure Central structure Back lift structure Front lift structure
❾
x1
❿
x1
Headphone hanger Cup holder
󰐖
x12
M6x38mm 󰐗
x4
M6x32mm 󰐘
x2
M6x25mm 󰐙
x6
M4x12mm 󰐚
x2
Non-locking
casters
󰐛
x2
Locking casters 󰐜
x4
sets
Cover and screw
knob, SET
󰀒
x1
Allen wrench 󰐝
x1
Cone wrench
(spanner)

BEFORE YOU START THE ASSEMBLY, PLEASE READ THE FOLLOWING TIPS AND WARNINGS.
P. 3 RTA-3800SU P. 3
❶Do a quick inventory to
make sure the package
contains all the parts and
hardware listed in the
assembly instructions.
❷Missing, damaged and
defective parts can be
replaced at no cost to you.
Please refer to the CONTACT
card included with the
product.
❸The replacement parts service
is limited to the continental United
States. If you reside in Hawaii,
Puerto Rico, U.S. Dependencies
or other countries, please contact
the supplier from where the unit
was purchased.
❹If during assembly you
find an issue or need
clarification, please contact
our Customer Service for
assistance. Please refer to the
CONTACT card included with
the product.
❺On each step read the
instructions and analyze the
illustrations thoroughly
before proceeding to do the
assembly.
❽Do not overtighten
or force the screws as
they might break, strip,
damage the threads of
the holes or get stuck
inside the part.
❻Make sure you understand
which hardware will be used
on each step. Using the wrong
size of screw, bolt or pin might
strip the threads or cause
damage to the part in which it
is being used.
❼To avoid misalignments,
always leave the screws
loose and tighten them until
all pieces are positioned
correctly.
❾Sometimes the laminate might cover partially or
entirely the hole on a panel. If there is no visible hole for
the screw, pass and press the tip of your finger over the
area where the hole should be located to feel the
indentation, and once found, carefully pierce the laminate
to reveal the hole underneath.
❿If the hole seems too small for the screw, first make
sure you are using the correct size of screw and that it’s
been installed in the correct hole. If the hole still appears to
be too small, carefully pierce the laminate to reveal the
hole’s actual size.

ASSEMBLY STEPS
First install the non-locking casters Ⓔat the back of the legs, and the locking casters Ⓕat
the front using the cone wrench (spanner) as shown. Then attach the covers/knobs sets Ⓖto
the top of the legs ③, but leave them loose.
STEP 1
Hardware/Tools:
󰐚2
Pcs
󰐛2
Pcs
󰐜4
Pcs
󰐝
P. 4 RTA-3800SU P. 4
Assemble the central structure ⑥in between the legs ③using screws Ⓐas shown.
STEP 2
Hardware/Tools:
󰐖
M6x38mm
4
Pcs
󰀒
NON-LOCKING GO
AT THE BACK
LOCKING GO
AT THE FRONT
Ⓔ
Ⓕ
Ⓖ
⑥
③
③
③
③
(Front)
(Front)

Assemble the back structure ④to the back lift structures ⑦using screws Ⓐas shown.
P. 5 RTA-3800SU P. 5
Assemble the front structure ⑤to the front lift structures ⑧using screws Ⓐas shown.
STEP 3
Hardware/Tools:
󰐖
M6x38mm
4
Pcs
󰀒
⑦
⑦
④
STEP 4
Hardware/Tools:
󰐖
M6x38mm
4
Pcs
󰀒
⑤
⑧
⑧

First make sure the covers and screw knobs Ⓖare loose, then insert the front lift structures
⑧thru the covers and into the legs ③, but DO NOT TIGHTEN the screw knobs yet.
STEP 5
P. 6 RTA-3800SU P. 6
Assemble the front tabletop ②to the frame using:
-Screws Ⓒto secure it to the front structure ⑤from underneath,
-Screws Ⓓto secure it to the front lift structures ⑧from underneath.
⑧
Ⓖ
⑧
③
③
STEP 6
Hardware/Tools:
󰐘
M6x25mm
2
Pcs
󰐙
M4x12mm
2
Pcs
󰀒
Ⓒ⑧
②
Ⓒ⑤Ⓓ
Ⓓ
(Front)
(Front)

P. 7 RTA-3800SU P. 7
Assemble the back tabletop ①to the back lift structures ⑦using screws Ⓑas shown.
STEP 8
Hardware/Tools:
󰐗M6x32mm
4
Pcs
󰀒
⑦
Unit is shown from
behind with its front
facing to the right.
STEP 7 First make sure the covers and screw knobs Ⓖare loose, then insert the back lift structures
⑦thru the covers and into the legs ③, but DO NOT TIGHTEN the screw knobs yet.
Ⓖ⑦
③
③
①
⑦
⑦
(Front)
(Front)

Assemble the headphone hanger ⑨and the cup holder ⑩to the front tabletop ②on the
sides of your preference using screws Ⓓfrom underneath as shown.
P. 8 RTA-3800SU P. 8
STEP 9
Hardware/Tools:
󰐙
M4x12mm
4
Pcs
󰀒
OR:
②
⑨
DONE! Before you start using the unit, make sure that all the screws and screw knobs are
properly tightened, and read all the warnings in the next page.
⑩
⑩
⑨
Finally, set the tabletops to the height of your preference, and proceed to tighten all the screw knobs Ⓖ.
②

AFTER THE ASSEMBLY IS DONE, PLEASE READ CAREFULLY THE FOLLOWING
CARE AND MAINTENANCE WARNINGS:
•Do not exceed the indicated weight limits.
•Do not use the unit as a step ladder.
•Do not expose the surfaces to direct sunlight or to extreme environmental conditions.
•Clean the surfaces preferable with a clean cloth damped in a solution of mild soap and water, then dry
with a clean towel.
•Do not use solvents or abrasive materials to clean the unit.
•If you decide to use a cleaning agent, test first on an area hidden from view such as underneath the
tabletops.
•Do not seat on the unit or lean against it.
•Do not allow small children to use or move the unit.
•Keep the unit with the casters locked at all times, except when needing to move it around.
•Before moving the unit, make sure that the front locking casters are unlocked.
•Keep all objects secured on the tabletops when moving the unit.
•Shall any part of the unit become defective during the warranty period, replacement parts might be
available to you at no charge. Please refer to the WARRANTY card included with the product.
•The warranty does not extend to regular wear and tear, nor the manufacturer assumes liability for
damages or consequences due to accidents, incorrect assembly, negligence, improper use, modifications,
or not heeding the above warnings.
•The warranty is limited to the continental United States. If you reside in Hawaii, Puerto Rico, U.S.
Dependencies or other countries, please contact the supplier from where the unit was purchased.
P. 9 RTA-3800SU P. 9
WEIGHT LIMITS
44 Lbs. (20 Kg)
2.2 Lbs. (1 Kg)
11 Lbs. (5 Kg)
2.2Lbs. (1 Kg)