RTA Products RTA-B002 User manual

Thank you for purchasing our product.
MODEL RTA-B002
ASSEMBLY INSTRUCTIONS
REV.LS-6501-0222-8
6FDQQR CodeWRYLHZ
IXOODVVHPEO\YLGHR

•Please read carefully the assembly instructions
before the installation.
• Do not discard this manual or any of the packaging
material until the unit has been completely
assembled.
•You can watch the complete assembly video
demonstration online by scanning the QR code on
the front page,as well you can watch the individual
steps by scanning the QR codes shown from page
5through page 9.
P. 1 RTA-B002 P. 1
SAMPLE - DO NOT SCAN

P. 2 RTA-B002 P. 2
1
x1
2
x1
3L
x2
4
x1
Left panel Right panel Locking caster Back panel
MAIN PARTS LIST
5
x1
6
x1
7
x1
8
x1
Front panel Middle shelf Bottom panel Top shelf
9
x2
10
x2
Stationary tube Adjustable “T”
tube
11A
x2
12
x1
Plastic
square cover
Main panel
3N
x2
Non-locking caster
11B
x2
Screw knob
13
x1
Top protection tube
MAIN PARTS LAYOUT (FOR
REFERENCE):
LIST OF HARDWARE, SCREWS AND
FITTINGS
PART
QTY ITEM
A16 M4x14
B2M6x25
C10 M6x35
D22 M6x40 Bolt
1Screwdriver
(top surface)
(bottom surface)
(top surface)
1
9
12
13
2
5
6
7
8
3L
11B
10 11A

P. 3 RTA-B002 P. 3
☛
☛
This unit uses cam bolts and locks. The following explains how to use them.
☛
☛
This unit uses cam bolts and locks. The following explains how to use them.
This unit uses cam bolts and locks. The following explains how to use them.
This is not an assembly step; it is a guide for when you are actually doing the
This is not an assembly step; it is a guide for when you are actually doing the
assembly using this kind of hardware.
Cam Bolt
Cam Lock
1. Screw the bolt into the corresponding hole
on panel “A”.
3. Insert the cam lock on panel “B” making
sure it goes aligned to receive the bolt’s head.
4. Turn the cam lock clockwise. This will lock the
parts together and will close any gaps.
Alignment: The cross points
towards the panel “A” with the bolt.
2. Join panel “B” to panel “A”. If panel “B” comes
with the cam lock pre-installed, make sure it is
aligned to receive the bolt’s head (refer to point
3). There might be a very small gap between the
panels which is normal.
Panel “B”
Panel “B”
Panel “B”
Panel “B”
Panel
“B”

BEFORE YOU START THE ASSEMBLY, PLEASE READ THE FOLLOWING TIPS AND WARNINGS.
❶Do aquick inventory
to make sure the package
contains all the parts and
hardware listed in the
assembly instructions.
❷Missing, damaged
and defective parts can
be replaced at no cost
to you. Please refer to
the last pages on this
manual.
❹If during assembly
you find an issue or
need clarification, please
contact our Customer
Service for assistance.
Please refer to the last
pages on this manual.
❺On each step read the
instructions and analyze
the illustrations thoroughly
before proceeding to do the
assembly.
❽Do not overtighten
or force the screws as
they might break, strip,
damage the threads of
the holes or get stuck
inside the part.
❻Make sure you
understand which
hardware will be used on
each step.Using the
wrong size of screw, bolt
or pin might strip the
threads or cause damage
to the part in which it is
being used.
❼To avoid
misalignments, always
leave the screws loose
and tighten them until
all pieces are
positioned correctly.
❾Sometimes the laminate might cover
partially or entirely the hole on apanel.If there
is no visible hole for the screw, pass and press
the tip of your finger over the area where the
hole should be located to feel the indentation,
and once found, carefully pierce the laminate to
reveal the hole underneath.
❿If the hole seems too small for the screw,
first make sure you are using the correct size of
screw and that it’s been installed in the correct
hole.If the hole still appears to be too small,
carefully pierce the laminate to reveal the
hole’s actual size.
P. 4 RTA-B002 P. 4
❸The replacement parts
service is limited to the
48 contiguous United States.
If you reside in Alaska,
Hawaii, Puerto Rico,
U.S. territories or other
countries, please contact the
supplier from where the unit
was purchased.

ASSEMBLY STEPS
•Attach bolts Dinto the indicated holes on the left panel 1.
•
•
On panels 4, 5and 6checkand make sure the cam locks on their left
side are aligned to receive the bolts.
Assemble the panels 4, 5and 6to panel 1and turn the cam locks to
lock the panels as explained in page 3. Note: Panels 4 and 6 do not
assemble one another, they just lay flushed.
STEP 1
Hardware:
DM6x40
Bolt
5
Pcs
P. 5 RTA-B002 P. 5
Screw bolts Dinto the corresponding holes on the right panel 2,then
align cam lockson panels 4, 5, 6and finally assemble panel 2to those
panels and turn the cam locks as explained in page 3.
4
1
Scan QR Code
to view this step
(Bottom)
(Top)
(Bottom)
STEP 2
Hardware:
DM6x40
Bolt
5
Pcs
65
Cam lock
alignment
Cam lock
alignment
4
2
65
Surface with cam
locks on 6 must face
towards the bottom
Surface with cam locks
on 4and 5must face
towards the interior
(Front)
(Top)
Scan QR Code
to view this step

P. 6 RTA-B002 P. 6
Use screws Ato assemble the casters 3to panel 7to its bottom surface
the following way:
Assemble the panels 1, 2and 4(from step 2) to the top surface of panel
7with bolts Das explained in page 3. Please make sure to identify the
correct holes where Dwill be installed on the bottom panel.
(Front)
STEP 3
Hardware:
A
M4x14
16
Pcs
STEP 4
Hardware:
DM6x40
Bolt
6
Pcs
7
3L
2
1
Cam lock
alignment
•Locking casters 3L go at the front of the panel.
•Non-Locking casters 3N go at the back of the panel.
LOCKING
go at the front
of the panel ,
with lock facing
towards the front
3N
7
(Front)
NON-LOCKING
go at the back
4
Scan QR Code
to view this step
Scan QR Code
to view this step

P. 7 RTA-B002 P. 7
Assemble the top shelf 8to panels 1, 2and 4with bolts Das explained
in page 3.
Assemble the stationary tubes 9to the side panels 1and 2with screws
Cfrom the sides and to the bottom panel 7from the bottom.
STEP 5
Hardware:
DM6x40
Bolt
6
Pcs
STEP 6
Hardware:
C
M6x35
6
Pcs
2
1
2
1
Cam lock
alignment
8
4
9
7
9
Scan QR Code
to view this step
Scan QR Code
to view this step

P. 8 RTA-B002 P. 8
Place the plastic covers 11A over the tubes 9with their threaded
holes facing towards the outside.
•Insert the adjustable “T” tubes 10 through the covers 11A and into the
tubes 9making sure the longer end of the square tubes facestowards
the front.
•Lift the tubes at least 7 inches (about an open hands’ width) and insert
and tighten the screw knobs 11B into the covers 11A.
•Both tubes should be lifted at the same height to be able to do the
next step properly.
Hole facing
towards the
outside
Longer end towards the front
(Lift at least 7")
(Insert 11B into
11A and tighten)
FIRST:
STEP 7
STEP 8
9
9
11A
10
10
11B
11B
11A
11A
11A
THEN:
11A
Scan QR Code
to view this step
Scan QR Code
to view this step

P. 9 RTA-B002 P. 9
Assemble the main panel 12 to the tubes 10 with screws Cfrom
underneath.
Assemble the protection tube 13 to the main panel 12 with screws B
from underneath.
(Front)
(Front)
STEP 9
Hardware:
C
M6x35
4
Pcs
STEP 10
Hardware:
B
M6x25
2
Pcs
10
12
13
10
12
Scan QR Code
to view this step
Scan QR Code
to view this step

P. 1 0 RTA-B002 P. 1 0
•Adjust the height of the main panel by loosening the screw knobs 11B
and re-tighten when the desired height is reached.
STEP 11
11B
ALL DONE!
Give yourself a nice pat on the back.
You did a great job!
11B
Scan QR Code
to view this step

WEIGHT LIMITS
P. 11 RTA-B002 P. 11
•Do not exceed the indicated weight limits.
•Because the lift and lock system on this unit consists of friction of metals, frequent
adjustments of the tabletop's height might cause scuffs on the paint on the metal tubes.
This consequence is not considered a defect, and even with the scuffs the unit should still
be able to function properly as intended.
•Do not over-tighten the screw knobs. Please note that frequent height adjustments and
over-tightening may cause the square covers to break, and such damage is not covered
by the product's warranty.
•Do not expose the surfaces to direct sunlight or to extreme environmental conditions.
•Clean the surfaces preferable with a clean cloth damped in a solution of mild soap and
water, then dry with a clean towel.
•Do not use solvents or abrasive materials to clean the unit.
•If you decide to use a cleaning agent, test first on an area hidden from view such as
underneath the tabletop.
•Do not climb on the base of the unit or use it as a moving vehicle.
•Before moving the unit, make sure to unlock the front casters.
•When moving the unit, make sure to secure any object that might fall off.
•When transporting the unit to places far away, protect and secure the unit to avoid damage
in transit.
•Shall any part of the unit become defective during the warranty period, replacement parts
might be available to you at no charge. Please refer to the last pages on this manual.
•The warranty does not extend to regular wear and tear, nor the manufacturer assumes
liability for damages or consequences due to accidents, incorrect assembly, negligence,
improper use, modifications, or not heeding the above warnings.
CARE, MAINTENANCE AND SAFETY WARNINGS:
20 Lbs.
(9 Kg)
20 Lbs.
(9 Kg)
15 Lbs.
(6.8 Kg)
20 Lbs.
(9 Kg)

RTA Products, LLC warrants to the Original Purchaser who acquired a new product from RTA
Products or its authorized resellers that this product will be free from defects in its
workmanship and materials, under normal use and service conditions, as described herein.
"Defects" as used in this warranty, is defined as any imperfections that impair the use of the
furniture or product. RTA Products LLC will replace any defective part, at its discretion, and
without charge to the original purchaser other than the freight from the end consumer to RTA
Products.
Replacement parts can only be supplied if parts are available. Items out of production may be
unavailable. This warranty will be effective for the applicable time period beginning the date
of purchase on your original sales receipt. RTA product’s obligation under this warranty is
limited to repairing or replacing products or parts as provided herein. This product has been
designed for and is intended for office and home-office use only. This warranty is Original
Purchaser’s sole remedy for product defects, and this warranty does not extend to any
product, or damage to any product, caused by or attributed to abuse or misuse, products
used for commercial or rental purposes, use modifications of, or attachments to the product,
and products or parts not used, maintained, or extended hereunder is in lieu of any and all
other warranties, express or implied, including without limitations any implied warranty or
merchantability or of fitness for a particular purpose. Please note, all desks made with PVC
Laminate surface should not be exposed to direct sunlight, as it may damage the material.
Damage of this nature is not covered under this warranty.
RTA Products will not be responsible for indirect, special, incidental or consequential
damages. This warranty is limited to merchandise purchased in the Continental United
States, excludes AK, HI and PR. Some States do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitations or exclusions may not apply to
you. This warranty gives you specific legal rights. You may also have other rights that may
vary from state to state.
RTA Products will advise you of the procedure to follow in making warranty claims. The
following are the procedures for warranty claims:
a. Call us Monday –Friday, from 9am-5pm (Eastern Time) at [phone] to explain the
defect and give your name, address and phone number. Please have ready the model
number of our product, date and place of purchase. You can also write to us by e-mail
to [e-mail] and include the same information.
b. If we determine that replacement will remedy the situation, and in order to determine the
extent or the cause of the defect, purchaser will need to send the part in question at
purchaser’s expense. Once we receive the part, we will examine it and determine
whether the claim is valid (or not), and then proceed to send the replacement. We will
ship the replacement at our expense.
P. 1 2 RTA-B002 P. 1 2
TECHNI MOBILI DESK WARRANTY
DESKS/LAPTOP CARTS/FILE CABINETS: LIMITED 5-YEAR WARRANTY

FOR SEVERAL HELP OPTIONS
INCLUDING REPLACEMENT PARTS ORDERS
_________________________________________________________________
VISIT: WWW.TECHNIMOBILI.COM
CLICK ON SUPPORT TAB
Scan QR Code to order replacement parts
OR EMAIL US: [e-mail]