RTA Products Techni Mobili RTA-3800SU User manual

Thank you for purchasing our product.
MODEL RTA-3800SU
ASSEMBLY INSTRUCTIONS
REV.032021-1

•Please read carefully the assembly instructions
before the installation.
•Do not discard this manual or any of the packaging
material until the unit has been completely
assembled.
•Might require two people.
P. 1 RTA-3800SU P. 1

P. 2 RTA-3800SU P. 2
1
x1
2
x1
Back tabletop Front tabletop
MAIN PARTS LIST
4
x1
5
x1
3
x2
6
x1
Back structure Front structure
Metal leg
Central structure
7
x2
8
x2
Back lift structure Front lift structure 9
x1
10
x1
Headphone hanger Cup holder
LIST OF HARDWARE, SCREWS AND FITTINGS
PART
QTY ITEM
A12 M6x38
B4M6x32
C2M6x25
D6M4x12
E2
Non-
locking
caster
F2Locking
caster
PART
QTY ITEM
G1 4Plastic
cover
G2 4Screw
knob
H1Allen
wrench
I1
Cone
wrench
(Spanner)

BEFORE YOU START THE ASSEMBLY, PLEASE READ THE FOLLOWING TIPS AND WARNINGS.
❶Do aquick inventory
to make sure the package
contains all the parts and
hardware listed in the
assembly instructions.
❷Missing, damaged
and defective parts can
be replaced at no cost
to you. Please refer to
the last pages on this
manual.
❸The replacement parts
service is limited to the
continental United States.
If you reside in Alaska,
Hawaii, Puerto Rico,
U.S. Dependencies or other
countries, please contact
the supplier from where the
unit was purchased.
❹If during assembly
you find an issue or
need clarification, please
contact our Customer
Service for assistance.
Please refer to the last
pages on this manual.
❺On each step read the
instructions and analyze
the illustrations thoroughly
before proceeding to do the
assembly.
❽Do not overtighten
or force the screws as
they might break, strip,
damage the threads of
the holes or get stuck
inside the part.
❻Make sure you
understand which
hardware will be used on
each step.Using the
wrong size of screw, bolt
or pin might strip the
threads or cause damage
to the part in which it is
being used.
❼To avoid
misalignments, always
leave the screws loose
and tighten them until
all pieces are
positioned correctly.
❾Sometimes the laminate might cover
partially or entirely the hole on apanel.If there
is no visible hole for the screw, pass and press
the tip of your finger over the area where the
hole should be located to feel the indentation,
and once found, carefully pierce the laminate to
reveal the hole underneath.
❿If the hole seems too small for the screw,
first make sure you are using the correct size of
screw and that it’s been installed in the correct
hole.If the hole still appears to be too small,
carefully pierce the laminate to reveal the
hole’s actual size.
P. 3 RTA-3800SU P. 3

ASSEMBLY STEPS
NON-LOCKING
AT THE BACK
LOCKING AT
THE FRONT
G1
(Front)
3
3
G2
F
E
First install the non-locking casters E at the back of the legs 3, and the
locking casters F at the front using the cone wrench (spanner) as shown.
Then attach the plastic covers G1 and screw knobs G2 to the top of the
legs 3, making sure the knob faces towards the back as shown.
STEP 1
Hardware:
E
Non
locking
2
Pcs
F
Locking
2
Pcs
G1
Covers
4
Pcs
G2
Screw
knob
4
Pcs
I
P. 4 RTA-3800SU P. 4
Assemble the central structure 6 in between the legs 3 using screws A
as shown.
STEP 2
Hardware:
A
M6x38
4
Pcs
H
63
3(Front)

P. 5 RTA-3800SU P. 5
Assemble the back structure 4to the back lift structures 7using screws
A as shown.
Assemble the front structure 5to the front lift structures 8using screws A,
making sure the holes on 5face UP as shown.
4
STEP 3
Hardware:
A
M6x38
4
Pcs
H
7
7
STEP 4
Hardware:
A
M6x38
4
Pcs
H
5
8
8
(Front)
(Front)

P. 6 RTA-3800SU P. 6
First make sure the screw knobs G2 are loose, then with the help of
another person, insert the front lift structures 8thru the covers G1 and
into the legs 3. DO NOT TIGHTEN the screw knobs yet.
Assemble the front tabletop 2to the frame using:
• Screws Cto secure it to the structure 5from underneath,
• Screws Dto secure it to the lift structures 8from underneath.
G
8
3
8
STEP 6
Hardware:
C
M6x25
2
Pcs
D
M4x12
2
Pcs
H
D
C
2
3
(Front)
CD
5
8
STEP 5
Cfor the front,
Dfor the back.
NOTE: The front of the
tabletop has the pre-
drilled holes near the
corner on both sides.

P. 7 RTA-3800SU P. 7
First make sure the screw knobs G2 are loose, then with the help of
another person, insert the back lift structures 7thru the covers G1 and
into the legs 3. DO NOT TIGHTEN the screw knobs yet.
Assemble the back tabletop 1to the back lift structures 7using screws B
as shown
G
3
7
STEP 8
Hardware:
B
M6x32
4
Pcs
H
1
3
(Front)
UNIT IS SHOWN
FROM BEHIND WITH
ITS FRONT FACING
TO THE RIGHT.
(Front)
7
STEP 7

P. 8 RTA-3800SU P. 8
Assemble the headphone hanger 9and the cup holder 10 to the front
tabletop 2on the sides of your preference using screws Dfrom
underneath as shown.
Proceed to set the heights of the tabletops according to your
preference, and tighten the screw knobs.
STEP 9
Hardware:
D
M4x12
4
Pcs
H
22
9
9
10
10
ALL DONE!
Give yourself a nice pat on the back. You did a great job!

AFTER THE ASSEMBLY IS DONE, PLEASE READ CAREFULLY THE FOLLOWING
CARE AND MAINTENANCE WARNINGS:
•Do not exceed the indicated weight limits.
•Do not expose the surfaces to direct sunlight or to extreme environmental conditions.
•Clean the surfaces preferable with a clean cloth damped in a solution of mild soap and
water, then dry with a clean towel.
•Do not use solvents or abrasive materials to clean the unit.
•If you decide to use a cleaning agent, test first on an area hidden from view such as
underneath the tabletop.
•Do not sit on the unit or lean against it.
•Always keep the unit with the front casters locked, and do not allow small children to
play under or over the unit, move it, or use it as moving vehicle to avoid the risk of
objects falling from it and hurting them.
•Before moving the unit, make sure to unlock the front casters and hold, secure or
remove any object that might fall off.
•When transporting the unit to places far away, protect and secure the unit to avoid
damage in transit.
•Shall any part of the unit become defective during the warranty period, replacement
parts might be available to you at no charge. Please refer to the last pages on this
manual.
•The warranty does not extend to regular wear and tear, nor the manufacturer assumes
liability for damages or consequences due to accidents, incorrect assembly,
negligence, improper use, modifications, or not heeding the above warnings.
WEIGHT LIMITS
P. 9 RTA-3800SU P. 9
44 Lbs.
(20 Kg)
2.2 Lbs.
(1 Kg)
2.2 Lbs.
(1 Kg)
11 Lbs.
(5 Kg)