RTA Products TECHNI MOBILI RTA-7310D User manual

INDUSTRIAL WRITING DESK
MODEL RTA-7310D
ASSEMBLY INSTRUCTIONS
REV.PFT-7059-1222
Thank you for purchasing our product
Scan QR to view full
assembly video

•
•Please be kind to our planet, when done with the assembly,
recycle any of the packaging materials that is accepted by
your city or recycling service. Thank you!
12
RTA-7310D
P.1 P.1
•Please read carefully the assembly instructions before the installation.
• Do not discard this manual or any of the packaging
material until the unit has been completely assembled.
•The assembly might require of 2 persons for certain steps. Before you
start the instalation, make sure there is someone else nearby to help you.
•Scan this QR code to view the complete assembly video online.
•For individual Step videos - please use the QR code found on
the corresponding step within the manual.
After the item is assembled, you can use rubbing alcohol to
erase or remove the visible part numbers printed or labeled
on the pieces.
SAMPLE - DO NOT SCAN

P.2 P.2
RTA-7310D
1
x1 2
x1 3
x1 4
x1
Left frame
The replacement parts service is limited to
the 48 contiguous United States.
If you reside in AK, HI, PR, U.S. territories
or other countries,
please contact the
supplier from where
the unit was purchased.
Missing, damaged and defective
parts can be replaced at no cost
to you. Please refer to the last
pages on this manual.
Do a quick inventory
of all the parts and
hardware listed below
MAIN PARTS LIST
Middle frame Right frame Bottom tube
5
x1 6
x1 7
x2 8
x2
Top-front tube Top-back tube Back support tube
"V" Top shelf support tube
9
x1 10
x1 11
x1 12
x2
Top shelf horizontal
tube Headphones hook CPU Panel Left shelf panel
13
x1 14
x1
Main panel Top shelf panel
33.5"
Frame #2 has more
holes than frame #1
33.5"
33.5"
30"
44.6"
2 holes on same side
1hole 2 holes on same side,
1 hole on opposite side 1 hole by the end

1
23
4
6
8
9
10
11
12
13
RTA-7310D
P.3 P.3
MAIN PARTS LAYOUT (For reference)
HARDWARE LIST
1M4 Allen Wrench
1M10 Spanner
INCLUDED TOOLS
1Phillips Screwdriver
PART QTY SIZE ITEM
C
D
E
F
M6x12
B
A
1
28
10
16
2
2
M6x30
M6x45
M3.5x12
M6, 10x11mm
Locking caster
14
8
7
5
12
G
2Non-locking
caster
M10

RTA-7310D
P.4 P.4
BEFORE YOU START THE ASSEMBLY, PLEASE READ THE FOLLOWING TIPS AND WARNINGS.
• If during assembly you find an issue or need clarification,
please contact our Customer Service for assistance.
Please refer to the last pages on this manual.
• On each step read the instructions thoroughly and
analyze the illustrations before proceeding to do the
assembly.
• Follow the instructions step by step and do not skip any
unless our Customer Service advises it is OK to do so.
• Do not overtighten or force the screws as they might
break, strip, damage the threads of the holes or get stuck
inside the part.
• Make sure you understand which hardware will be
used on each step. Using the wrong size of screw,
bolt or pin might strip the threads or cause damage
to the part in which it is being used.
• To avoid misalignments, always leave the screws loose
and tighten them until all pieces are positioned correctly.
• If the hole seems too small for the screw, make sure you
are using the correct size of screw and/or that you are
installing it in the correct hole.
• Do not discard this manual or any of the packaging
material until the unit has been completely assembled.
√
√
M6
30mm
M6x30
•Sometimes on the panels the laminate or material might be
covering the hole partially or entirely. If there is no visible
hole or it seems too small, pass and press the tip of your
finger over the area where the hole should be located to feel
its indentation, and once found, carefully pierce the laminate
to uncover the hole underneath.

STEP 2
Hardware
BM6x30 4
Pcs
Tools (included)
Scan QR to view step
RTA-7310D
Assemble the first left shelf 12 to the middle bars on the frames 1and 2
with screws Bfrom underneath.
Assemble the second left shelf 12 to the bottom bars on the frames 1
and 2with screws Bfrom underneath.
1
2
12
(Top)
Make sure to place the frame with
this hole towards the back of the
unit, it is needed for step 3.
1
2
12
(Top)
P.5 P.5
STEP 1
Hardware
BM6x30 4
Pcs
ASSEMBLY STEPS
Tools (included)
Scan QR to view step

M10
RTA-7310D
Bring the cabinet built in step 2 to the upright position, then with the
help of another person:
• Assemble the tubes 4,5and 6to the middle frame 2in their
respective positions with screws C.
• Assemble the right frame 3to the tubes 4,5and 6with screws C.
• Attach the hook 10 to the frame 3with screw A
• Assemble the support tubes 7to the top tube 6on the back of the unit
with screws Cfrom outside and nut caps Efrom inside.
• Assemble the support tubes 7to the bottom tube 4with screws B
from underneath.
Note: If you don’t see holes for the screws on the tubes 4and 6, review
step 3for the correct assembly of those tubes.
2
3
4
5
6
A10
(Front)
(Back)
(Front)
7
6
4
E
C
B
Please pay attention to
the orientation of the
holes on all the tubes
P.6
P.6
STEP 3
Hardware
AM6x12 1
Pc
C
This step
requires of
2 persons
CM6x45 6
Pcs
Tools (included)
Scan QR to view step
STEP 4
Hardware
BM6x30 2
Pcs
CM6x45 2
Pcs
Tools (included)
Scan QR to view step
from the inside.
C
EM6 2
Pcs

RTA-7310D
Assemble the top shelf support tubes 8to the shelf horizontal tube 9with
screws C.
Assemble the tubes 8and 9to the top shelf panel 14 with screws B.
9
Please pay attention to
the orientation of the
holes on the tubes
8
8
8
8
9
14
With the help of another person, assemble the main panel 13 to the
tubes 8with screws Bmaking sure the bottom surface faces UP like
shown in the illustration.
8
8
(Bottom surface)
(Top surface)
13
P.7 P.7
STEP 5
Hardware
CM6x45 2
Pcs
Tools (included)
Scan QR to view step
STEP 6
Hardware
BM6x30 6
Pcs
Tools (included)
Scan QR to view step
STEP 7
Hardware
BM6x30 4
Pcs
Tools (included)
Scan QR to view step
This step
requires of
2 persons

Option 1
RTA-7310D
With the help of another person, assemble the main panel 13 to the
frames 1,2and 3and to the tubes 5and 6with screws Bfrom
underneath.
Note: If you don’t see holes for the screws on the tubes 5and 6, review
step 3
Assemble the casters Fand Gto the CPU panel 11 with screws D,
making sure the Locking casters Fare attached on the same side that
will be considered the FRONT of the cart.
F
13
1
23
5
6
11
G
G
F
STEP 8
Hardware
BM6x30 8
Pcs
Tools (included)
Scan QR to view step
This step
requires of
2 persons
for the correct assembly of those tubes.
P.8 P.8
STEP 9
Hardware
DM3.5x12 16
Pcs
FLocking
2
Pcs
Tools (included)
Scan QR to view step
GNon-locking
2
Pcs
Option 2
Give yourself a nice pat on the back, you did a great job!
ALL DONE!

P.9 P.9
RTA-7310D
Clean the surfaces preferable with a clean cloth damped in a solution of mild soap and water,
then dry with a clean towel.
If you decide to use a cleaning agent, test first on an area hidden from view such as
underneath the tabletop.
Every 4 months, inspect the unit completely and make sure that all screws are tighten.
When transporting the unit to places far away, protect and secure the unit to avoid damage in
transit.
Shall any part of the unit become defective during the warranty period, replacement parts
might be available to you at no charge. Please refer to the last pages on this manual.
The warranty does not extend to regular wear and tear, nor the manufacturer assumes liability
for damages or consequences due to accidents, incorrect assembly, negligence, improper
use, modifications, or not heeding the above warnings.
WEIGHT LIMITS
CARE AND MAINTENANCE
WARNINGS
Do not exceed the indicated weight limits.
Do not expose the surfaces to direct sunlight or to extreme environmental conditions.
Do not use solvents or abrasive materials to clean the unit.
Do not sit on the unit or lean against it.
Do not allow small children to play under or over the unit.
Do not allow small children to play with the CPU cart as a moving vehicle.
Do not pull, push or drag the unit to move it for more than 1 feet. The unit must be lifted by at
least 2 persons when moving in the same or adjacent rooms.
Before moving the unit, make sure to secure or remove any object that is heavy or might fall off.
When lifting the unit, use both hands and bend your knees, not your backs.
88 Lbs
(40 Kg) 44 Lbs
(20 Kg)
44 Lbs
(20 Kg)
66 Lbs
(30 Kg) 2.2 Lbs
(1 Kg)

P.10 P.10
RTA-7310D
TECHNI MOBILI WARRANTY
RTA Products, LLC warrants to the Original Purchaser who acquired a new product from RTA
Products or its authorized resellers that this product will be free from defects in its workmanship
and materials, under normal use and service conditions, as described herein. "Defects" as used
in this warranty, is defined as any imperfections that impair the use of the furniture or product.
RTA Products LLC will replace any defective part, at its discretion, and without charge to the
original purchaser other than the freight from the end consumer to RTA Products.
Replacement parts can only be supplied if parts are available. Items out of production may be
unavailable. This warranty will be effective for the applicable time period beginning the date of
purchase on your original sales receipt. RTA product’s obligation under this warranty is limited to
repairing or replacing products or parts as provided herein. This product has been designed for
and is intended for office and home-office use only. This warranty is Original Purchaser’s sole
remedy for product defects, and this warranty does not extend to any product, or damage to any
product, caused by or attributed to abuse or misuse, products used for commercial or rental
purposes, use modifications of, or attachments to the product, and products or parts not used,
maintained, or extended hereunder is in lieu of any and all other warranties, express or implied,
including without limitations any implied warranty or merchantability or of fitness for a particular
purpose. Please note, all desks made with PVC Laminate surface should not be exposed to
direct sunlight, as it may damage the material. Damage of this nature is not covered under this
warranty.
RTA Products will not be responsible for indirect, special, incidental or consequential damages.
This warranty is limited to merchandise purchased in the Continental United States, excludes
AK, HI and PR. Some States do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitations or exclusions may not apply to you. This
warranty gives you specific legal rights. You may also have other rights that may vary from state
to state.
RTA Products will advise you of the procedure to follow in making warranty claims. The following
are the procedures for warranty claims:
a. Call us Monday – Friday, from 9am-5pm (Eastern Time) at [phone] to explain the
defect and give your name, address and phone number. Please have ready the model number
of our product, date and place of purchase. You can also write to us by e-mail to
[email protected] and include the same information.
b. If we determine that replacement will remedy the situation, and in order to determine the
extent or the cause of the defect, purchaser will need to send the part in question at purchaser’s
expense. Once we receive the part, we will examine it and determine whether the claim is valid
(or not), and then proceed to send the replacement. We will ship the replacement at our
expense.
DESKS/LAPTOP CARTS/FILE CABINETS: LIMITED 5-YEAR WARRANTY

Your satisfaction is very important to us. Our Support agents can help
you with any issues you may have, please feel free to contact us with any
questions you have about our products, or to request replacement parts.
FOR ADDITIONAL INFORMATION
PLUS HELP OPTIONS
VISIT: WWW.TECHNIMOBILI.COM
CLICK ON SUPPORT TAB
Or scan the following QR Code:
[email protected]
EMAIL US:
To request replacement parts, email us with the model number
of the product, the part number or letter of the requested part,
and proof of purchase.