RTA Products Techni Mobili RTA-3788 User manual

Imported By
Thank you for purchasing one of our products.
Please read carefully the assembly instructions before the installation.
Do not discard this manual or any of the packaging material until the unit
has been completely assembled.
MODEL RTA-3788
ASSEMBLY INSTRUCTIONS
MIGHT REQUIERE
OF 2 PERSONS

Left structure Right structure Lower panel
Casters: Horizontal tube Back panel Vertical tubes
Auxiliary panel Support tubes
(for glass top)
Support tubes
(for keyboard tray)
Slider bases
Keyboard sliders
SET:
Keyboard panel Glass tabletop
MAIN PARTS LIST
SET of 2 pcs
2 locking
P.2
RTA-3788
P.2
2 non-locking
RIGHT
LEFT

SCREWS LIST:
P.3
RTA-3788
P.3
MAIN PARTS LAYOUT (FOR REFERENCE):

BEFORE YOU START THE ASSEMBLY, PLEASE READ THE FOLLOWING TIPS AND WARNINGS.
•Do a quick inventory to make sure the product contains all the parts and hardware.
•
Missing, damaged and defective parts can be replaced at no cost to you. Please refer to the CONTACT card
included with the product.
•The replacement parts service is limited to the continental United States. If you reside in Hawaii, Puerto
Rico, U.S. Dependencies or other countries, please contact the supplier from where the unit was purchased.
•If during assembly you find an issue or need clarification, please contact our Customer Service for
assistance. Please refer to the CONTACT card included with the product.
•On each step read the instructions and analyze the illustrations thoroughly before proceeding to do the
assembly.
•Make sure you understand which hardware will be used on each step. Using the wrong size of screw, bolt or
pin might strip the threads or cause damage to the part in which it is being used.
•To avoid misalignments, always leave the screws loose and tighten them until all pieces are positioned
correctly.
•Do not overtighten or force the screws as they might break, strip, damage the threads of the holes or get
stuck inside the part.
•Sometimes the laminate might cover partially or entirely the hole on a panel, but the hole should still be
located under the laminate.
•If there is no visible hole for the screw, pass and press the tip of your finger over the area where the hole
should be located to feel the indentation, and once found, carefully pierce the laminate to reveal the hole
underneath.
•If the hole seems too small for the screw, first make sure you are using the correct size of screw and that it’s
been installed in the correct hole. If the hole still appears to be too small, carefully pierce the laminate to
reveal the hole’s actual size.
P.4
RTA-3788
P.4

ASSEMBLY STEPS
P.5
RTA-3788
P.5
Following the orientation of the structures (1L) and (1R) as shown, install the casters (3)
on the bottom of the structures with the locking at the front and the non-locking at the back.
Use
screws D to assemble the horizontal tube (4) between the left and right structures (1L),
(1R).
PAY ATTENTION TO THE CORRECT ORIENTATION OF ALL THE PARTS.
STEP 1
STEP 2
Screws:
D
6x50mm
2
pcs
NON-LOCKING
(Front)
(Front)
LOCKING
(Front)
(Front)
1L is the one
with one hole
in the middle LEFT
RIGHT

P.6
RTA-3788
P.6
Use screws H to assemble the lower panel (2) to the structures (1L) and (1R) as shown.
Use screws and nuts B to assemble the back panel (5) to the main structures (1L), (1R) as
shown. Note that the screws enter from the outside of the structures.
Use screws D to assemble the vertical tubes (6) to the horizontal tube (4).
STEP 3
Screws:
H
6x65mm
4
pcs
STEP 4
Screws:
B
6x65mm
4
pcs
STEP 5
Screws:
D
6x50mm
2
pcs
The panel has insert nuts for the screws.
If alignment is needed, use a flat head
screwdriver and turn the nut to align it
so it can properly receive the screw.
If the holes don’t align, review
step 2 for the correct assembly
and orientation of the structures.
(This shows the parts
from step 3 viewed
from behind)
(Front)
(This shows the parts
from step 4 viewed
from the front)
(Front)
(Front)

P.7
RTA-3788
P.7
Assemble the auxiliary panel (7) to the unit using:
- Screws D to assemble it to the back panel (5) from behind the unit;
- Screws A to assemble it to the vertical tubes (6) from underneath.
Use screws E to assemble the support tubes (9) to the glass tabletop (13) as shown.
First place the support tubes (8) over
the holes of the structures (1L) and
(1R), then carefully and with the
help of another person, place the
glass tabletop (13) over the tubes,
and finally secure the top using
screws C from underneath as shown.
STEP 6
Screws:
A
6x35mm
2
pcs
D
6x50mm
2
pcs
STEP 7
Screws:
E
6x20mm
2
pcs
The panel has insert nuts for the screws.
If alignment is needed, use a flat head
screwdriver and turn the nut to align it
so it can properly receive the screw.
If the holes don’t align with tubes
(6), review steps 2 and 5 for the
correct assembly and orientation
of the parts.
STEP 8
Screws:
C
6x85mm
4
pcs
MIGHT REQUIERE
OF 2 PERSONS

Use screws F to assemble the sliders (11) to the slider bases (10) as shown. Note that the
screw enter thru the tube and into the slider, not from the slider into the tube.
Assemble the slider bases (10) to the unit using:
- Screws D to assemble it to the horizontal tube (4) from behind the unit;
- Screws A to assemble it to the support tubes (9) from underneath.
Place the keyboard panel over the tabs of the sliders (11) and assemble it from underneath
using screws (G) as shown.
P.8
RTA-3788
P.8
STEP 9
Screws:
F
4x23mm
4
pcs
STEP 11
Screws:
G
4x14mm
4
pcs
Note the correct orientation
of all the parts.
(Front)
STEP 10
Screws:
A
6x35mm
2
pcs
D
6x50mm
2
pcs
DONE! Before you start using the unit, make sure that all the screws, bolts, etc. are properly tightened,
and read all the warnings in the next page.
Note that the tabs on
the sliders face down.

AFTER THE ASSEMBLY IS DONE, PLEASE READ CAREFULLY THE FOLLOWING
CARE AND MAINTENANCE WARNINGS:
•Do not exceed the indicated weight limits.
•Do not expose the surfaces to direct sunlight or to extreme environmental conditions.
•Clean the surfaces preferable with a clean cloth damped in a solution of mild soap and water,
then dry with a
clean towel.
•Do not use solvents or abrasive materials to clean the unit.
•If you decide to use a cleaning agent, test first on an area hidden from view such as underneath the
keyboard panel.
•Do not lean against the unit.
•Do not allow small children to play under or over the unit, or move/roll it.
•Before moving the unit, make sure that the front casters are unlocked, and remove any object that is heavy
or might fall off.
•
When transporting the unit to other places, protect and secure the unit to avoid damage in transit. Also make
sure to block the casters to avoid unexpected rolling inside the transportation vehicle.
•The glass is made of safety tempered glass. The safety feature is that when breakage occurs, the glass
shatters into many tiny pieces minimizing the risk of serious injuries. If the glass breaks, do not handle the
pieces with your bare hands, take some pictures and contact Customer Service immediately. Please refer to
the Contact Us card.
•Shall any part of the unit become defective during the warranty period, replacement parts might be available
to you at no charge. Please refer to the WARRANTY card included with the product.
•The warranty does not extend to regular wear and tear, nor the manufacturer assumes liability for damages
or consequences due to accidents, incorrect assembly, negligence, improper use, modifications, or not
heeding the above warnings.
•The warranty is limited to the continental United States. If you reside in Hawaii, Puerto Rico, U.S.
Dependencies or other countries, please contact the supplier from where the unit was purchased.
P.9
RTA-3788
P.9
WEIGHT LIMITS 50 Lbs. (22.68 Kg)
22 Lbs. (9.97 Kg)
20 Lbs. (9.07 Kg)
30 Lbs. (13.60 Kg)