RTA Products TECHNI MOBILI RTA-B006 User manual

Thank you for purchasing our product.
MODEL RTA-B006
ASSEMBLY INSTRUCTIONS
REV.LS-6541-0322-1

•Please read carefully the assembly instructions
before the installation.
•Do not discard this manual or any of the packaging
material until the unit has been completely
assembled.
•Might require two people.
P.1 RTA-B006 P.1

P.2 RTA-B006 P.2
1
x1 2
x2 3
x54
x1
Bottom panel Lower side panel Caster Back panel
MAIN PARTS LIST
5
x2 6
x2 7
x1 8
x1
Top panel Upper side panel Metal star base Pneumatic lift
cylinder
9
x1 10
x4
Mechanism Hinge
11
x1 Base center cover
MAIN PARTS LAYOUT (FOR
REFERENCE): LIST OF HARDWARE, SCREWS AND
FITTINGS
PART
QTY ITEM
A8M6x35
B6M6x40 Bolt
C16 M3x20
D4M6x12
1Screwdriver
ATTENTION:
This piece comes pre-
installed in the middle
of the base #7, and is
of the same color.

BEFORE YOU START THE ASSEMBLY, PLEASE READ THE FOLLOWING TIPS AND WARNINGS.
❶Do aquick inventory
to make sure the package
contains all the parts and
hardware listed in the
assembly instructions.
❷Missing, damaged
and defective parts can
be replaced at no cost
to you. Please refer to
the last pages on this
manual.
❹If during assembly
you find an issue or
need clarification, please
contact our Customer
Service for assistance.
Please refer to the last
pages on this manual.
❺On each step read the
instructions and analyze
the illustrations thoroughly
before proceeding to do the
assembly.
❽Do not overtighten
or force the screws as
they might break, strip,
damage the threads of
the holes or get stuck
inside the part.
❻Make sure you
understand which
hardware will be used on
each step.Using the
wrong size of screw, bolt
or pin might strip the
threads or cause damage
to the part in which it is
being used.
❼To avoid
misalignments, always
leave the screws loose
and tighten them until
all pieces are
positioned correctly.
❾Sometimes the laminate might cover
partially or entirely the hole on apanel.If there
is no visible hole for the screw, pass and press
the tip of your finger over the area where the
hole should be located to feel the indentation,
and once found, carefully pierce the laminate to
reveal the hole underneath.
❿If the hole seems too small for the screw,
first make sure you are using the correct size of
screw and that it’s been installed in the correct
hole.If the hole still appears to be too small,
carefully pierce the laminate to reveal the
hole’s actual size.
P.3 RTA-B006 P.3
❸The replacement parts
service is limited to the
48 contiguous United States.
If you reside in Alaska,
Hawaii, Puerto Rico,
U.S. territories or other
countries, please contact the
supplier from where the unit
was purchased.

ASSEMBLY STEPS
Assemble the lower panels 2to the top surface of the bottom panel 1
with screws Afrom underneath.
STEP 1
Hardware:
AM6x35
6
Pcs
P.4 RTA-B006 P.4
Assemble the back panel 4
to the bottom panel 1with
screws Afrom underneath.
2
1. Align cam locks 2. Join panels 3. Turn cam locks
5
6
Cam locks
alignment
2
Top surface:
Bottom surface:
STEP 2
Hardware:
AM6x35
2
Pcs
Attach the bolts Bto the
top panels 5.
STEP 3
Hardware:
BM6x40
Bolt
6
Pcs
4
1
5
5
STEP 4 •On the upper side panels 6, check and make sure the cam locks are
aligned to receive the bolts Bfrom panels 5. If they are crooked, use
the screwdriver to turn them and align them.
•Join panel 6to panel 5and then turn the cam locks to lock the parts.
5
6
1
(Front)
(Back)
6

P.5 RTA-B006 P.5
Place the side panels and 6side-by-side as shown in the illustration,
then attach the hinges 10WRWKHVHSDQHOVwith screws C.
Place the tabletop upside-
down and attach the
mechanism 9to the
bottom panel 1with
screws Dmaking sure the
handle faces towards the
RIGHT of the unit.
STEP 5
Hardware:
CM3x20
16
Pcs
STEP 6
Hardware:
DM6x12
4
Pcs
55
7
11
1
Insert the casters 3into the holes of the
base 7using pressure.
STEP 7
1
7
9
3
Attach the cap 11 to the
middle of the base 7.
NOTE: The cap 11
usually comes already
inserted in the middle
of the base 7, you can
skip this step if that is
the case.
STEP 8
(Right)
(Front)
6
6



P.6 RTA-B006 P.6
Insert the lift cylinder 8in the middle of the
base 7, then place the tabletop making
sure the tip of the lift cylinder enters into
the hole of the mechanism 9.
STEP 9
9
8
ALL DONE!
Give yourself a nice pat on the back.
You did a great job!
LIFT FUNCTION, NOTES
•The lift function on this unit is similar to that of office chairs.
•To lift the unit just lift the handle UP, you might have to give a little push also.
•To bring the unit down, lift the handle UP and at the same time apply force DOWN on
the tabletop. Just like a chair, the unit goes down by force of heavy weight on the unit.
•This unit stands like a chair with free rotation side to side, it is not possible to keep the
unit stationary in one specific position.
LIFT THE UNIT:
Lift handle UP
LOWER THE UNIT:
Lift handle UP and at
the same time push
DOWN on the
tabletop with force.
7
8
1
PUSH
DOWN
Tabletop rotates freely

WEIGHT LIMITS
P.7 RTA-B006 P.7
•Do not exceed the indicated weight limits.
•Do not expose the surfaces to direct sunlight or to extreme environmental conditions.
•Clean the surfaces preferable with a clean cloth damped in a solution of mild soap and
water, then dry with a clean towel.
•Do not use solvents or abrasive materials to clean the unit.
•If you decide to use a cleaning agent, test first on an area hidden from view such as
underneath the tabletop.
•Do not allow small children to play with the unit.
•Do not lean against the unit as it may suddenly roll away.
•Do not use the unit as a chair or moving vehicle.
•When moving the unit, make sure to hold or secure any object that might fall off.
•When transporting the unit to places far away, bring it down to the lowest height and
protect and secure the unit to avoid damage in transit.
•Shall any part of the unit become defective during the warranty period, replacement parts
might be available to you at no charge. Please refer to the last pages on this manual.
•The warranty does not extend to regular wear and tear, nor the manufacturer assumes
liability for damages or consequences due to accidents, incorrect assembly, negligence,
improper use, modifications, or not heeding the above warnings.
CARE, MAINTENANCE AND SAFETY WARNINGS:
5.5 Lbs.
(2.5 Kg)
5.5 Lbs.
(2.5Kg)
22 Lbs.
(10Kg)
11 Lbs.
(5.5 Kg)
11 Lbs.
(5.5 Kg)
22 Lbs.
(10 Kg)
(OPEN)
(CLOSED)

RTA Products, LLC warrants to the Original Purchaser who acquired a new product from RTA
Products or its authorized resellers that this product will be free from defects in its
workmanship and materials, under normal use and service conditions, as described herein.
"Defects" as used in this warranty, is defined as any imperfections that impair the use of the
furniture or product. RTA Products LLC will replace any defective part, at its discretion, and
without charge to the original purchaser other than the freight from the end consumer to RTA
Products.
Replacement parts can only be supplied if parts are available. Items out of production may be
unavailable. This warranty will be effective for the applicable time period beginning the date
of purchase on your original sales receipt. RTA product’s obligation under this warranty is
limited to repairing or replacing products or parts as provided herein. This product has been
designed for and is intended for office and home-office use only. This warranty is Original
Purchaser’s sole remedy for product defects, and this warranty does not extend to any
product, or damage to any product, caused by or attributed to abuse or misuse, products
used for commercial or rental purposes, use modifications of, or attachments to the product,
and products or parts not used, maintained, or extended hereunder is in lieu of any and all
other warranties, express or implied, including without limitations any implied warranty or
merchantability or of fitness for a particular purpose. Please note, all desks made with PVC
Laminate surface should not be exposed to direct sunlight, as it may damage the material.
Damage of this nature is not covered under this warranty.
RTA Products will not be responsible for indirect, special, incidental or consequential
damages. This warranty is limited to merchandise purchased in the Continental United
States, excludes AK, HI and PR. Some States do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitations or exclusions may not apply to
you. This warranty gives you specific legal rights. You may also have other rights that may
vary from state to state.
RTA Products will advise you of the procedure to follow in making warranty claims. The
following are the procedures for warranty claims:
a. Call us Monday –Friday, from 9am-5pm (Eastern Time) at [phone] to explain the
defect and give your name, address and phone number. Please have ready the model
number of our product, date and place of purchase. You can also write to us by e-mail
to [e-mail] and include the same information.
b. If we determine that replacement will remedy the situation, and in order to determine the
extent or the cause of the defect, purchaser will need to send the part in question at
purchaser’s expense. Once we receive the part, we will examine it and determine
whether the claim is valid (or not), and then proceed to send the replacement. We will
ship the replacement at our expense.
P.8 RTA-B006 P.8
TECHNI MOBILI DESK WARRANTY
DESKS/LAPTOP CARTS/FILE CABINETS: LIMITED 5-YEAR WARRANTY

FOR SEVERAL HELP OPTIONS
INCLUDING REPLACEMENT PARTS ORDERS
_________________________________________________________________
VISIT: WWW.TECHNIMOBILI.COM
CLICK ON SUPPORT TAB
Scan QR Code to order replacement parts
OR EMAIL US: [e-mail]