RTA Products Techni Mobili RTA-KS40C User manual

Thank you for purchasing our product.
MODEL RTA-KS40/K45C
ASSEMBLY INSTRUCTIONS
REV.092021-3

A
x1 B
x1 C
x1 D
x1
Backrest Seat 5-Leg star
base Mechanism
MAIN PARTS LIST
E
x1
F
x5 G-L
x1 G-R
x2
Pneumatic
lift cylinder
Casters Left
armrest Right
armrest H
X1 Set Covers for
gas lift
LIST OF HARDWARE
PART
QTY ITEM USE IN
I4M6x20 Mechanism to seat
J8M6x25 Armrests to seat and
backrest
K4Washers Mechanism
L8Hole covers Armrests
M1M4 Allen wrench Steps 2, 4 and 5
P.1 RTA-KS40/K45C P.1
Sitting on the chair, not looking at it

BEFORE YOU START THE ASSEMBLY, PLEASE READ THE FOLLOWING TIPS
AND WARNINGS.
❶Do a quick inventory to
make sure the package
contains all the parts and
hardware listed in the
assembly instructions.
❷Missing, damaged
and defective parts can
be replaced at no cost to
you. Please refer to the
last page in this manual.
❸The replacement parts
service is limited to the 48
contiguous United States.
If you reside in Alaska,
Hawaii, Puerto Rico,
U.S. Territories or other
countries, please contact
the supplier from where the
unit was purchased.
❹If during assembly
you find an issue or
need clarification,
please contact our
Customer Service for
assistance. Please refer
to the last page in this
manual.
❺On each step read
the instructions and
analyze the
illustrations thoroughly
before proceeding to
do the assembly.
❽Do not overtighten
or force the screws as
they might break, strip,
damage the threads of
the holes or get stuck
inside the part.
❻Make sure you
understand which hardware
will be used on each step.
Using the wrong size of
screw, bolt or pin might
strip the threads or cause
damage to the part in which
it is being used.
❼To avoid
misalignments, always
leave the screws loose
and tighten them until
all pieces are
positioned correctly.
❾If the hole seems too big or too small for the
screw, first make sure you are using the correct
size of screw and that it’s been installed in the
correct hole. Test another of the same screw
into the same hole, as well as test the screw
onto different holes for the same part. If the
hole still appears to be too small, do not force
it, it needs replacing.
P.2 RTA-KS40/K45C P.2

ASSEMBLY STEPS
Insert the casters Finto
the legs of the base C
using pressure, then place
the gas lift Ein the middle
of the base and cover it
with H.
Turn over the seat Bwith
its front end away from
you,and using screws I
and washers K,assemble
the mechanism Dwith its
lever facing to your LEFT
as shown.
(Front)
Put the seat over the
base parts making sure
the tip of the gas lift E
enters into the hole of
the mechanism D.
Please note that the
lever will be located on
the RIGHT side when
sitting on the chair.
(Front)
P.3 RTA-KS40/K45C P.3
STEP 2
Hardware
IM6x20 4
Pcs
K4
Pcs
M
STEP 1
STEP 3
F
E
C
H
I
K
D
E
B
D

Assemble the armrests Gto
the seat Bin their respective
sides using screws J,but
leave the screws very loose
to allow flexibility for the
next step.
Assemble the backrest Ato
the armrests Gusing screws
Jand proceed to tighten all
the screws.
Cover the screw holes
on the armrests G
with the caps L.
P.4 RTA-KS40/K45C P.4
STEP 4
Hardware
JM6x25 4
Pcs
M
STEP 6
Hardware
L8
Pcs
ALL DONE! Give yourself a nice pat on the back. You did a great job!
LEFT
G-L
RIGHT
G-R
B
(Front)
STEP 5
Hardware
JM6x25 4
Pcs
M
G-R
G-L
Leave all the
screws loose
A

CHAIR’S FUNCTIONS
To raise or lower the chair’s height, pull UP the lever that is under the seat. The chair
goes down while sitting on it, or up if you lift your body.
Please note that this chair does not recline.
WARNINGS
• Do not exceed the indicated weight limit.
• Do not allow your children to stand up on the chair or use it as ladder.
•Use the chair to sit only one child at a time.
• Do not use the chair if parts are damaged or if screws are loose or missing.
• Do not allow the children to sit near the edge of the seat and encourage them to always
sit properly on the chair to avoid going beyond their balance point and fall off the chair.
• Do not allow the children to play with the chair or use it as a racing vehicle.
• Not paying attention to these warnings could result in severe injuries.
•To clean the chair it is recommended to use a soft cloth lightly damped in a solution of
smooth soap and water, then dry with a clean towel.
•Do not use solvents or abrasive materials to clean any part of the chair.
•Before applying a cleaning agent, test on a small hidden area of the chair, like
underneath the seat.
•Do not expose the product to direct sunlight or to extreme environmental conditions.
•Every 4 months, inspect the chair completely and make sure that all screws are
tighten.
CARE AND MAINTENANCE
P.5 RTA-KS40/K45C P.5
Weight
Limit:
140 Lbs

TECHNI MOBILI CHAIR WARRANTY
TASK/KID'S CHAIR: 1-YEAR WARRANTY
EXECUTIVE/MANAGER CHAIR: 2-YEAR WARRANTY
1.RTA Products, LLC has warranted the Techni Mobili office chairs to the original purchaser
who acquired a new product from RTA Products or its authorized resellers of the product
against defects in material or workmanship.
2.This warranty is expressly limited to the repair or replacement (at its option) of defective
chair components or materials that fails under normal use as a result of a defect in materials
or workmanship. This warranty is limited to merchandise purchased in the Continental United
States. No assembly labor is included. The word "defects" as used in this warranty, is defined
as imperfections that impair the utility of the product.
3.This warranty applies under conditions of normal use, but does not apply to defects that
result from intentional damage, negligence, unreasonable use or exposure.
4.Liability for consequential damages is excluded to the extent exclusion is permitted by law.
This warranty gives you specific legal rights, and you may have other rights that vary from
State to State.
5.RTA Products does not warrant: a) natural variations in character marks b) changes in
surface finishes due to aging or exposure to light c) marks, scars, or wrinkles occurring
naturally in leather d) failure resulting from normal wear and tear e) the matching of colors,
grains, or textures of natural materials f) the colorfastness or the matching of textiles,
including an exact match to cuttings or to swatch cards g) damage, marking, or staining of
veneer surfaces due to contact with rubber or similar compounds, damage from sharp objects
or imprinting from writing instruments, or prolonged exposure to direct sunlight h) we do not
warrant products that are exposed to extreme environmental conditions or that have been
subject to improper storage.
6.RTA Products shall not be liable for loss of time, inconvenience, commercial loss, or
incidental or consequential damages.
7.Any modification to the original product voids the warranty. We do not warrant the
performance of the product when used in combination with other than original products.
8.This product has been designed for and is intended for office and home-office use only.
This warranty is Original Purchaser’s sole remedy for product defects, and this warranty does
not extend to any product, or damage to any product, caused by or attributed to abuse or
misuse, products used for commercial or rental purposes, use modifications of, or
attachments to the product, and products or parts not used, maintained, or extended
hereunder is in lieu of any and all other warranties, express or implied, including without
limitations any implied warranty or merchantability or of fitness for a particular purpose.
9.Report any defects to RTA Products, LLC together with your sales receipt or other proof of
purchase. If the chair is defective within the terms of the warranty, RTA Products, LLC will
furnish a replacement chair (at its option) at no cost of equal or similar value and design.
10.RTA Products will advise you of the procedure to follow in making warranty claims. The
following are the procedures for warranty claims:
a) Call us Monday –Friday, from 9am-5pm (Eastern Time) at [phone] to explain the
defect and give your name, address and phone number. Please have ready the model
number of our product, date and place of purchase. You can also write to us by e-mail
to [e-mail] and include the same information.
b) If we determine that replacement will remedy the situation, and in order to determine the
extent or the cause of the defect, purchaser will need to send the part in question at
purchaser’s expense. Once we receive the part, we will examine it and determine whether the
claim is valid (or not), and then proceed to send the replacement. We will ship the
replacement at our expense.
P.6 RTA-KS40/K45C P.6

FOR SEVERAL HELP OPTIONS
INCLUDING REPLACEMENT PARTS ORDERS
_________________________________________________________________
VISIT: WWW.TECHNIMOBILI.COM
CLICK ON SUPPORT TAB
Scan QR Code to order replacement parts
OR EMAIL US: [e-mail]
P.7 RTA-KS40/K45C P.7