RTA Products Techni Mobili RTA-K250D User manual

Thank you for purchasing our product.
MODEL RTA-K250D
ASSEMBLY INSTRUCTIONS
REV.ZLR-6589-0322-0

•Please read carefully the assembly instructions
before the installation.
•Do not discard this manual or any of the packaging
material until the unit has been completely
assembled.
•Might require two people.
P. 1 RTA-K250D P. 1
LIST OF HARDWARE, SCREWS AND FITTINGS
PART QTY ITEM
I2M6x35
J12 M6x13
K4M6x10
L4Ø6x18
PART QTY ITEM
M4Glide stud
N4M6x50
1Allen
Wrench
A
x1
B
x2
C
x1
Tabletop Metal leg Top-front metal bar
MAIN PARTS LIST
D
x1
E
x1
F
x2
G
x1
Top-back metal bar
Bottom-back metal
bar
Metal support bar Metal cup holder H
x1
Metal headset
hanger

BEFORE YOU START THE ASSEMBLY, PLEASE READ THE FOLLOWING TIPS AND WARNINGS.
❶Do aquick inventory
to make sure the package
contains all the parts and
hardware listed in the
assembly instructions.
❷Missing, damaged
and defective parts can
be replaced at no cost
to you. Please refer to
the last pages on this
manual.
❹If during assembly
you find an issue or
need clarification, please
contact our Customer
Service for assistance.
Please refer to the last
pages on this manual.
❺On each step read the
instructions and analyze
the illustrations thoroughly
before proceeding to do the
assembly.
❽Do not overtighten
or force the screws as
they might break, strip,
damage the threads of
the holes or get stuck
inside the part.
❻Make sure you
understand which
hardware will be used on
each step.Using the
wrong size of screw, bolt
or pin might strip the
threads or cause damage
to the part in which it is
being used.
❼To avoid
misalignments, always
leave the screws loose
and tighten them until
all pieces are
positioned correctly.
❾Sometimes the laminate might cover
partially or entirely the hole on apanel.If there
is no visible hole for the screw, pass and press
the tip of your finger over the area where the
hole should be located to feel the indentation,
and once found, carefully pierce the laminate to
reveal the hole underneath.
❿If the hole seems too small for the screw,
first make sure you are using the correct size of
screw and that it’s been installed in the correct
hole.If the hole still appears to be too small,
carefully pierce the laminate to reveal the
hole’s actual size.
P. 2 RTA-K250D P. 2
❸The replacement parts
service is limited to the
48 contiguous United States.
If you reside in Alaska,
Hawaii, Puerto Rico,
U.S. territories or other
countries, please contact the
supplier from where the unit
was purchased.

ASSEMBLY STEPS
With the help of another person, and with the legs Bupside-down, attach
to them the top-front and top-back metal bars Cand Dwith screws J.
STEP 1
Hardware:
J
M6x13
8
Pcs
P. 3 RTA-K250D P. 3
With the help of another person, assemble the bottom-back metal bar E
to the legs Bwith screws I.
STEP 2
Hardware:
I
M6x35
2
Pcs
Assemble the metal support bars Fto the top-back bar Dand the
bottom-back bar Ewith screws Jas shown.
STEP 3
Hardware:
J
M6x13
4
Pcs
B
B
(Bottom)
(Top)
(Front)
(Back)
D
C
Make sure the holes on
D go oriented towards
the back for step 3.
B
B
E
Make sure the holes on
E go oriented towards
the back for step 3.
F
F
E
D

P. 4 RTA-K250D P. 4
•Place the tabletop Aupside-down over carpeting or any large soft
cloth to protect its top surface.
•With the help of another person, place the frame built in step 3over
the tabletop making sure the holes coincide.
•Assemble the legs Bto the tabletop Awith washers Land screws N,
but screw loosely and do not tighten until all 4 screws are in place.
STEP 4
Hardware:
L
Ø6x18
4
Pcs
NM6x50
4
Pcs
Use screws Kto assemble the cup holder Gon the side and the headset
hanger Hon the front of the tabletop Aas shown.
STEP 5
Hardware:
K
M6x10
4
Pcs
Install the glides Mto the legs Band then with the help of another
person, bring the unit upright.
STEP 6
Hardware:
M
Glides
4
Pcs
(Front)
(Back)
B
A
B
L
N
(Front)
G
H
A

WEIGHT LIMITS
P. 5 RTA-K250D P. 5
•Do not exceed the indicated weight limits.
•Do not expose the surfaces to direct sunlight or to extreme environmental conditions.
•Clean the surfaces preferable with a clean cloth damped in a solution of mild soap and
water, then dry with a clean towel.
•Do not use solvents or abrasive materials to clean the unit.
•If you decide to use a cleaning agent, test first on an area hidden from view such as
underneath the tabletop.
•Do not allow the children to climb over the unit.
•Do not pull, push or drag the unit to move it for more than 1 feet. The unit must be lifted by
at least 2 adult persons when moving in the same or adjacent rooms.
•Before moving the unit, make sure to secure or remove any object that is heavy or might
fall off.
•When lifting the unit, use both hands and bend your knees, not your backs.
•When transporting the unit to places far away, protect and secure the unit to avoid damage
in transit.
•Shall any part of the unit become defective during the warranty period, replacement parts
might be available to you at no charge. Please refer to the last pages on this manual.
•The warranty does not extend to regular wear and tear, nor the manufacturer assumes
liability for damages or consequences due to accidents, incorrect assembly, negligence,
improper use, modifications, or not heeding the above warnings.
CARE, MAINTENANCE AND SAFETY WARNINGS:
100 Lbs.
(45.5 Kg)
13.2 Lbs.
(6 Kg)
13.2 Lbs.
(6 Kg)

RTA Products, LLC warrants to the Original Purchaser who acquired a new product from RTA
Products or its authorized resellers that this product will be free from defects in its
workmanship and materials, under normal use and service conditions, as described herein.
"Defects" as used in this warranty, is defined as any imperfections that impair the use of the
furniture or product. RTA Products LLC will replace any defective part, at its discretion, and
without charge to the original purchaser other than the freight from the end consumer to RTA
Products.
Replacement parts can only be supplied if parts are available. Items out of production may be
unavailable. This warranty will be effective for the applicable time period beginning the date
of purchase on your original sales receipt. RTA product’s obligation under this warranty is
limited to repairing or replacing products or parts as provided herein. This product has been
designed for and is intended for office and home-office use only. This warranty is Original
Purchaser’s sole remedy for product defects, and this warranty does not extend to any
product, or damage to any product, caused by or attributed to abuse or misuse, products
used for commercial or rental purposes, use modifications of, or attachments to the product,
and products or parts not used, maintained, or extended hereunder is in lieu of any and all
other warranties, express or implied, including without limitations any implied warranty or
merchantability or of fitness for a particular purpose. Please note, all desks made with PVC
Laminate surface should not be exposed to direct sunlight, as it may damage the material.
Damage of this nature is not covered under this warranty.
RTA Products will not be responsible for indirect, special, incidental or consequential
damages. This warranty is limited to merchandise purchased in the Continental United
States, excludes AK, HI and PR. Some States do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitations or exclusions may not apply to
you. This warranty gives you specific legal rights. You may also have other rights that may
vary from state to state.
RTA Products will advise you of the procedure to follow in making warranty claims. The
following are the procedures for warranty claims:
a. Call us Monday –Friday, from 9am-5pm (Eastern Time) at [phone] to explain the
defect and give your name, address and phone number. Please have ready the model
number of our product, date and place of purchase. You can also write to us by e-mail
to [e-mail] and include the same information.
b. If we determine that replacement will remedy the situation, and in order to determine the
extent or the cause of the defect, purchaser will need to send the part in question at
purchaser’s expense. Once we receive the part, we will examine it and determine
whether the claim is valid (or not), and then proceed to send the replacement. We will
ship the replacement at our expense.
P. 6 RTA-K250D P. 6
TECHNI MOBILI DESK WARRANTY
DESKS/LAPTOP CARTS/FILE CABINETS: LIMITED 5-YEAR WARRANTY

FOR SEVERAL HELP OPTIONS
INCLUDING REPLACEMENT PARTS ORDERS
_________________________________________________________________
VISIT: WWW.TECHNIMOBILI.COM
CLICK ON SUPPORT TAB
Scan QR Code to order replacement parts
OR EMAIL US: [e-mail]