Ruijie Reyee RG-ES106D-P Installation and operating manual

f
RG-ES106D-P,RG-ES126S-LP,RG-ES110D-P,
RG-ES118S-LP,RG-ES116G, RG-ES124GD
Series Switch
Hardware Installation and Reference Guide
Document
Version: V1.2
Date: 2023-02-15
Copyright © 2023Ruijie Networks

Copyright
Copyright © 2023Ruijie Networks
All rights arereservedin this documentandthis statement.
Without the priorwritten consentof Ruijie Networks,anyorganizationorindividual shall notreproduce,extract,
back up, modify, or propagatethe content of this documentinany mannerorin anyform, or translateit into
other languagesoruse some orallparts of the documentforcommercial purposes.
,, andother Ruijie networks logos are
trademarks ofRuijieNetworks.
All othertrademarks orregistered trademarks mentionedinthis documentare owned bytheir respective
owners.
Disclaimer
The products,services,orfeatures you purchasearesubjecttocommercialcontracts andterms,andsomeor
allof the products,services,orfeatures describedinthis document maynot be available for you to purchaseor
use.Except for the agreementinthe contract,RuijieNetworks makes no explicitorimplicitstatementsor
warranties withrespecttothe content of this document.
The content of this documentwill be updatedfrom timeto timedue to productversionupgrades orother
reasons,Ruijie Networksreserves the rightto modifythe content of the documentwithoutanynotice or prompt.
This manualis designedmerelyas auserguide.RuijieNetworks has triedits bestto ensuretheaccuracyand
reliabilityof the content whencompiling this manual,butit does notguaranteethat the content of the manual is
completelyfree of errors or omissions,and all the information in this manual doesnotconstituteanyexplicit or
implicitwarranties.

Ruijie RG-ES100 Series Switches Hardware Installation and Reference Guide
Preface
Thank you for usingourproducts.This manual willguideyouthroughtheinstallation ofthe device.
This manual describes the functional and physical features and provides the device installation steps, hardware
troubleshooting,moduletechnicalspecifications,andspecifications and usageguidelines forcables andconnectors.
Audience
It is intended fortheusers whohave some experiencein installingand maintaining networkhardware.At thesame time,
it is assumedthatthe users arealreadyfamiliarwiththe relatedterms and concepts.
Obtaining Technical Assistance
Ruijie Networks website:https://www.ruijienetworks.com/
Technicalsupportwebsite:https://ruijienetworks.com/support
Caseportal:https://caseportal.ruijienetworks.com
Community:https://community.ruijienetworks.com
Technicalsupportemail:[e-mail]
Skype: [e-mail]
Related Documents
Document
Description
ConfigurationGuide
Describes network protocols and related mechanisms that
supported bythe product,with configurationexamples.
Command Reference
Describes the related configuration commands, including
command modes, parameter descriptions, usage guides, and
relatedexamples.
Conventions
1. GUI Symbols
Interface
symbol
Description
Example
Boldface
1. Button names
2. Window names, tab name, field name
andmenuitems
3. Link
1. Click OK.
2. Select Config Wizard.
3. Click the Download File link.
>
Multi-level menus items
ChooseSystem >Time.
2. Signs
The signs used in this documentaredescribed as follows.

Ruijie RG-ES100 Series Switches Hardware Installation and Reference Guide
Warning
An alert that calls attention to importantrules and information thatif not understood orfollowed can resultin
data loss orequipmentdamage.
Caution
An alert that calls attention to essential information thatifnot understood orfollowed can resultin function
failureor performancedegradation.
Note
An alert that contains additional orsupplementaryinformation thatifnot understood orfollowed will notlead to
serious consequences.
Specification
An alert that contains adescription ofproductor version support.
1 Product Overview
The RG-ES100series switchesincludethefollowingmodels.
Model
10/100Base-TX Auto-sensing
Ethernet Port
10/100/1000Base-T
Auto-sensing
Ethernet Port
1000Base-X SFP
Port
Console
Port
RG-ES106D-P
6 (ports 1–4supportPoE/PoE+)
N/A
N/A
N/A
RG-ES126S-LP
24(ports 1–24supportPoE/PoE+)
2
1 (combo)
N/A
RG-ES110D-P
8 (ports 1–8supportPoE/PoE+)
2
N/A
N/A
RG-ES116G
N/A
16
N/A
N/A
RG-ES124GD
N/A
24
N/A
N/A
RG-ES118S-LP
16 (ports 1–16supportPoE/PoE+)
2
2 (combo)
N/A
1000Base-Tis backward compatiblewith100Base-TXand 10Base-T.
The SFP ports cannotbe backward compatible with 100Base-FX.
1.1 RG-ES106D-P
Technical Specifications
Model
RG-ES106D-P
Ports
Six 10/100Base-TXauto-sensingEthernetports
Ports 1–4 supportPoE/PoE+.
Power Supply
AC input

Ruijie RG-ES100 Series Switches Hardware Installation and Reference Guide
Rated voltage range: 100V AC to 240 V AC
Maximum voltage range: 90V AC to 264 V AC
Frequency: 50/60 Hz
Rated current: 1.5 A
Adapter output
Rated voltage range: 51V DC
Rated current range:1.25 A
EEE
Not supported
PoE
PoE/PoE+ support
Ports 1 to4 support PoE/PoE+with themaximum power outputof 30W per port.Ports 5–6do
not supportPoEor PoE+.
The overall maximum outputpowerofPoE or PoE+ is 58 W.
Power
Consumption
Less than7 W with noPoE load
Less than 67 W withPoE full load
Operating
Temperature
0°C to 45°C (32°Fto 113°F)
Storage
Temperature
-40°C to +70°C (-40°F to +158°F)
Operating Humidity
10%to 90%RH
Storage Humidity
5% to 95% RH
Port Mode
Switchover in threemodes:
1. Flow Control On
2. Flow Control Off
3. Port Isolation
When port isolation is enabled, ports 1-4are isolated from each other, but can communicate
with ports 5 and6.
Fan
Not supported
Temperature
Warning
Not supported
Accessing Optical
Module Information
Not supported
Certification
CE
Earth Leakage
Current
≤1.5 mA
Dimensions
(W x D x H)
100mm x 100mm x 26 mm (3.94in. x 3.94 in. x 1.02 in.)
Weight
(With Package)
0.66 kg (1.46lbs)
Device operationin a residential environmentmaycauseradio interference.
Product Appearance
The RG-ES106D-P provides six 10/100Base-TX auto-sensing Ethernet ports on the front panel, and a port mode
switchoverbutton, a system status LED,a powersocket,and a grounding poleontheback panel.

Ruijie RG-ES100 Series Switches Hardware Installation and Reference Guide
Figure 1-1 Appearanceof the RG-ES106D-P
Front Panel
Figure 1-2 Front Panel of the RG-ES106D-P
Note:
1. Electrical port status LED
2. PoE status LED
3. 10/100Base-TXPoE port
4. 10/100Base-TXauto-sensing Ethernetport
5. Nameplate on the bottom of the device
Back Panel
Figure 1-3 Back Panel of the RG-ES106D-P
5

Ruijie RG-ES100 Series Switches Hardware Installation and Reference Guide
Note:
1. Port mode switchoverbutton
2. System status LED
3. DC powersocket
4. Grounding pole
Heat Dissipation
The RG-ES106D-P adopts natural heat dissipation, therebyensuring normal operation. You must maintain aminimum
clearance of100mm (3.94in.)aroundthe RG-ES106D-P.Itis recommendedthatyou clean the RG-ES106D-Ponceevery
3 months to avoid dustfrom blockingvents.
LEDs
LED
Panel Identification
State
Meaning
System status LED
PWR
Off
The switchis poweredoff.
Solidgreen
The switchis operational.
RJ45 port status LED
Upper leftcornerofthe
port
Off
The port is not connected.
Solidgreen
The port is connectedat a rate of 10/100 Mbps.
Blinking green
The port is receiving or sending traffic at a rateof
10/100Mbps.
RJ45PoE status LED
Upper leftcornerofthe
port
Off
PoE does notsupplypower.
Solidgreen
PoE is operational.
1.2 RG-ES126S-LP
Technical Specifications

Ruijie RG-ES100 Series Switches Hardware Installation and Reference Guide
Model
RG-ES126S-LP
Ports
Ports 1 to 24are 10/100Base-TXauto-sensing Ethernetports,andsupportPoE/PoE+.
Ports 25and 26 are 10/100/1000Base-Tauto-sensing Ethernetports, anddonotsupportPoE
or PoE+.
Port 26Fis a 1000Base-XSFPport multiplexedwith port 26 as a combo port,and theSFPport
is preferred.
Power Supply
AC input
Rated voltage range: 100V AC to 240 V AC
Maximum voltage range: 90V AC to 264 V AC
Frequency: 50/60 Hz
Rated current: 4 A (max.)
EEE
Not supported
PoE
PoE/PoE+ support
Ports 1to24support PoE/PoE+withthemaximum power outputof30W perport.Ports 25and
26 donot supportPoE or PoE+.
The overall maximum outputpowerofPoE or PoE+ is 180 W.
Power
Consumption
Less than 10 W withno PoE load
Less than 220 W with PoE full load
Operating
Temperature
0°C to 45°C (32°Fto 113°F)
Storage
Temperature
-40°C to +70°C (-40°F to +158°F)
Operating Humidity
10%to 90%RH
Storage Humidity
5% to 95% RH
Port Mode
Sswitchoverin threemodes:
1. Flow Control On
2. Flow Control Off
3. Port Isolation
When portisolationis enabled,ports 1to22 are isolated from eachother,butcancommunicate
with ports 25, 26, and 26F.
Fan
Supported
Temperature
Warning
Not supported
Accessing Optical
Module Information
Not supported
Certification
CE
Earth Leakage
Current
≤1.5 mA
Dimensions
(W x D x H)
440mm x 208mm x 44 mm (17.32in. x 8.19 in. x 1.73 in.)
Weight
(With Package)
3 kg (6.61 lbs)
Device operationin a residential environmentmaycauseradio interference.

Ruijie RG-ES100 Series Switches Hardware Installation and Reference Guide
Product Appearance
The RG-ES126S-LP provides twenty-four 10/100Base-TX auto-sensing Ethernet ports, two 10/100/1000Base-T auto-
sensingEthernetports,one1000Base-XSFPport,system status LEDs,a portmodeswitchoverbutton on thefrontpanel,
anda powersocketand a grounding poleontheback panel.
Figure 1-4 Appearance of the RG-ES126S-LP
Front Panel
Figure 1-5 Front Panel of the RG-ES126S-LP
Note:
1. PoE overload LED
2. System status LED
3. Port status LED
4. PoE status LED
5. Port mode switchoverbutton
6. 10/100Base-TXauto-sensing Ethernetport
7. 10/100/1000Base-Tauto-sensing Ethernetport
8. 10/100/1000Base-Tcombo port
9. Nameplate onthebottom of the device
Back Panel
Figure 1-6 Back Panel of the RG-ES126S-LP
9

Ruijie RG-ES100 Series Switches Hardware Installation and Reference Guide
Note:
1. Grounding pole
2. AC powersocket
Heat Dissipation
TheRG-ES126S-LPadopts fans forheatdissipation,therebyensuring normaloperation.You mustreserve 10 cmdistance
space atboth sides andthe backplane ofthecabinet toallowairflow. Itis recommended thatyou cleantheRG-ES126S-
LP onceevery 3 months toavoid dustfrom blockingvents.
LEDs
LED
Panel Identification
State
Meaning
System status LED
PWR
Off
The switchis poweredoff.
Solidgreen
The switchis operational.
PoE overloadLED
PoE-max
Off
The overall PoE output does not reach the
maximum power.
Solidgreen
The overall PoE output reaches the maximum
power.
RJ45 port status LED
Link/Act
(1–24,25, 26/26F)
Off
The port is not connected.
Solidgreen
The port is connected at a rate of 10/100/1000
Mbps.
Blinking green
The port is receiving or sending traffic at a rateof
10/100/1000Mbps.
RJ45PoE status LED
PoE (1–24)
Off
PoE does notsupplypower.
Solidgreen
PoE is operational.
1.3 RG-ES110D-P
Technical Specifications
Model
RG-ES110D-P
Ports
Eight 10/100Base-TXauto-sensing Ethernetports (autoMDI/MDIX), andPoE/PoE+ support
Two 10/100/1000Base-Tauto-sensingEthernetports (autoMDI/MDIX)
Power Supply
AC input

Ruijie RG-ES100 Series Switches Hardware Installation and Reference Guide
Rated voltage range: 100V AC to 240 V AC
Maximum voltage range: 90V AC to 264 V AC
Frequency: 50/60 Hz
Rated current: 1.6 A
Adapter output
Rated voltage range: 53.5 V DC
Rated current range:2.24 A
EEE
Port 1–8: supported
Port 9–10: notsupported
PoE
SupportPoE and PoE+.
Ports 1 to 8 support PoE/PoE+ with the maximum power output of 30 W per port. Ports 9–10
do not supportPoEor PoE+.
The overall maximum outputpowerofPoE/PoE+ is 110 W.
Power
Consumption
Less than8 W with noPoE load
Less than 129 W with PoE full load
Operating
Temperature
0°C to 45°C (32°Fto 113°F)
Storage
Temperature
-40°C to +70°C (-40°F to +158°F)
Operating Humidity
10%to 90%RH
Storage Humidity
5% to 95% RH
Port Mode
Switchover in threemodes:
1. Flow Control On
2. Flow Control Off
3. Port Isolation
When port isolation is enabled, ports 1-8are isolated from each other, but cancommunicate
with ports 9 and 10.
Fan
Not supported
Temperature
Warning
Not supported
Accessing Optical
Module Information
Not supported
Certification
CE
Earth Leakage
Current
≤1.5 mA
Dimensions
(W x D x H)
190mm x 100mm x 28 mm (7.48in. x 3.94 in. x 1.1 in.)
Weight
(With Package)
1.3 kg (2.87 lbs)
Device operationin a residential environmentmaycauseradio interference.
Product Appearance

Ruijie RG-ES100 Series Switches Hardware Installation and Reference Guide
The RG-ES110D-P provides eight 10/100Base-TX auto-sensing Ethernet ports, two 10/100/1000Base-T auto-sensing
Ethernetports,and LED indicators onthe frontpanel,and apowersocket, aportmode switchoverbutton,and agrounding
poleon the backpanel.
Figure 1-7 Appearanceof the RG-ES110D-P
Front Panel
Figure 1-8 Front Panel of the RG-ES110D-P
Note:
1. System status LED
2. Port status LED
3. PoE status LED
4. 10/100Base-TXPoE port
5. 10/100/1000Base-Tauto-sensing Ethernetport
6. Nameplate on the bottom of the device
Back Panel
Figure 1-9 Back Panel of the RG-ES110D-P
6

Ruijie RG-ES100 Series Switches Hardware Installation and Reference Guide
Note:
1. Grounding pole
2. Port mode switchoverbutton
3. DC powersocket
Heat Dissipation
The RG-ES110D-P adopts naturalheat dissipation, therebyensuring normal operation. Youmust maintain a minimum
clearance of100mm (3.94in.)aroundthe RG-ES110D-P.Itis recommended thatyou clean the RG-ES110D-Ponce every
3 months toavoid dustfrom blocking vents.
LEDs
LED
Panel Identification
State
Meaning
System status LED
PWR
Off
The switchis poweredoff.
Solidgreen
The switchis operational.
RJ45 port status LED
Link/ACT (1–10)
Off
The port is not connected.
Solidgreen
The port is connected at a rate of 10/100/1000
Mbps.
Blinking green
The port is receiving or sending traffic at a rateof
10/100/1000Mbps.
RJ45PoE status LED
PoE (1–8)
Off
PoE does notsupplypower.
Solidgreen
PoE is operational.
Blinking green
PoE is overloaded.

Ruijie RG-ES100 Series Switches Hardware Installation and Reference Guide
1.4 RG-ES118S-LP
Technical Specifications
Model
RG-ES118S-LP
Ports
Sixteen 10/100Base-TXauto-sensing Ethernetports (autoMDI/MDIX), andPoE/PoE+ support
Two 1000Base-XSFP comboports
Power Supply
AC input
Rated voltage range: 100V AC to 240 V AC
Maximum voltage range: 90V AC to 264 V AC
Frequency: 50/60 Hz
Rated current: 2.5 A
EEE
Ports 1–16: supported
Ports17–18:notsupported
PoE
PoE/PoE+ support
Ports 1 to16 supportPoE/PoE+ withthe maximum power outputof 30W perport.Ports 17-18
do not supportPoEor PoE+.
The overall maximum outputpowerofPoE/PoE+ is 120 W.
Power
Consumption
Less than 13 W withno PoE load
Less than 148 W with PoE full load
Operating
Temperature
0°C to 45°C (32°Fto 113°F)
Storage
Temperature
-40°C to +70°C (-40°F to +158°F)
Operating Humidity
10%to 90%RH
Storage Humidity
5% to 95% RH
Port Mode
Switchover in threemodes:
1. Flow Control On
2. Flow Control Off
3. Port Isolation
When portisolation is enabled,ports 1-16 areisolated from eachother, butcancommunicate
with ports 17and 18.
Fan
Not supported
Temperature
Warning
Not supported
Accessing Optical
Module Information
Not supported
Certification
CE
Earth Leakage
Current
≤1.5 mA
Dimensions
(W x D x H)
440mm x 208mm x 44 mm (17.32in. x 8.19 in. x 1.73 in.)
Weight
3.40 kg (7.50lbs)

Ruijie RG-ES100 Series Switches Hardware Installation and Reference Guide
(With Package)
Device operationin a residential environmentmaycauseradio interference.
Product Appearance
The RG-ES118S-LPprovides sixteen10/100Base-TXauto-sensingEthernetports,two 1000Base-XSFPcombo ports,a
port mode switchoverbuttonand LED indicators onthe frontpanel,anda powersocketand a groundingpoleontheback
panel.
Figure 1-4 Appearance of the RG-ES118S-LP
Front Panel
Figure 1-5 Front Panel of the RG-ES118S-LP
Note:
1. System status LED
2. Port status LED
3. PoE status LED
4. Port mode switchoverbutton
5. 10/100Base-TXauto-sensing Ethernetport
6. 10/100/1000Base-Tcombo port
7. Nameplate onthebottom of the device
Back Panel
Figure 1-6 Back Panel of the RG-ES118S-LP
7

Ruijie RG-ES100 Series Switches Hardware Installation and Reference Guide
Note:
1. Grounding pole
2. AC powersocket
Heat Dissipation
TheRG-ES118S-LPadopts fans forheatdissipation,therebyensuring normaloperation.Youmustreserve10cmdistance
space atboth sides andthe backplane ofthecabinet toallowairflow. Itis recommendedthatyou cleantheRG-ES118S-
LP onceevery 3 months toavoid dustfrom blockingvents.
LEDs
LED
Panel Identification
State
Meaning
System status LED
PWR
Off
The switchis poweredoff.
Solidgreen
The switchis operational.
RJ45 port status LED
Link/ACT (1–16)
Off
The port is not connected.
Solidgreen
The port is connectedat a rate of 10/100 Mbps.
Blinking green
The port is receiving or sending traffic at a rateof
10/100Mbps.
ComboportLED
Link/ACT
(17/17F, 18/18F)
Off
The port is not connected.
Solidorange
The port is connectedat a rate of 100Mbps.
Blinking orange
The port is receiving or sending traffic at a rateof
100Mbps.
Solidgreen
The port is connectedat a rate of 1000Mbps.

Ruijie RG-ES100 Series Switches Hardware Installation and Reference Guide
Blinking green
The port is receiving or sending traffic at a rateof
1000Mbps.
RJ45PoE status LED
PoE (1–16)
Off
PoE does notsupplypower.
Solidgreen
PoE is operational.
Blinking green
PoE is overloaded.
1.5 RG-ES116G
Technical Specifications
Model
RG-ES116G
Ports
Sixteen 10/100/1000Base-Tauto-sensingEthernetports
Power Supply
AC input
Rated voltage range: 100V AC to 240 V AC
Maximum voltage range: 90V AC to 264 V AC
Frequency: 50/60 Hz
Rated current: 0.5 A
EEE
Not supported
PoE
Not supported
Power
Consumption
11 W
Operating
Temperature
0°C to 45°C (32°Fto 113°F)
Storage
Temperature
-40°C to +70°C (-40°F to +158°F)
Operating Humidity
10%to 90%RH
Storage Humidity
5% to 95% RH
Port Mode
Switchover in four modes:
1. Flow Control On
2. Flow Control Off
3. Port Isolation
When portisolation is enabled,ports 1-14 areisolated from eachother, butcancommunicate
with ports 15and 16.
4. ExtendData Transmission-10Mbps:Whenthis modeis enabled,ports 1–8haveareduced
speed of 10Mbps, with atransmission distance of up to 250 m. Ifcompatibilityis considered,
some ports maynot deliversuch a transmission distance.
Fan
Not supported
Temperature
Warning
Not supported

Ruijie RG-ES100 Series Switches Hardware Installation and Reference Guide
Accessing Optical
Module Information
Not supported
Certification
CE
Earth Leakage
Current
≤1.5 mA
Dimensions
(W x D x H)
280mm x 126mm x 44 mm (11.02in. x 4.96 in. x 1.73 in.)
Weight
(With Package)
1.75 kg (3.86lbs)
Device operationin a residential environmentmaycauseradio interference.
Product Appearance
The RG-ES116G provides sixteen 10/100/1000Base-Tauto-sensing Ethernet ports, aport mode switchover buttonand
LED indicators onthefront panel, anda powersocketand a groundingpoleonthe back panel.
Figure 1-10 Appearanceof the RG-ES116G
Front Panel
Figure 1-11 Front Panel of the RG-ES116G
5

Ruijie RG-ES100 Series Switches Hardware Installation and Reference Guide
Note:
1. System status LED
2. Port status LED
3. Port mode switchoverbutton
4. 10/100/1000Base-Tauto-sensing Ethernetport
5. Nameplate on the bottom of the device
Back Panel
Figure 1-12 Back Panel of the RG-ES116G
Note:
1. Grounding pole
2. AC powerport
Heat Dissipation
The RG-ES116G adopts natural heat dissipation, thereby ensuring normal operation. You must maintain a minimum
clearance of 100 mm (3.94 in.) aroundthe RG-ES116G. Itis recommended thatyou clean the RG-ES116G once every3
months toavoid dustfrom blocking vents.
LEDs
LED
Panel Identification
State
Meaning
System status LED
Power
Off
The switchis poweredoff.
Solidgreen
The switchis operational.
RJ45 port status LED
Link/ACT (1-16)
Off
The port is not connected.
Solidorange
The port is connectedat a rate of 10/100 Mbps.

Ruijie RG-ES100 Series Switches Hardware Installation and Reference Guide
Blinking orange
The port is receiving or sending traffic at a rateof
10/100Mbps.
Solidgreen
The port is connectedat a rate of 1000Mbps.
Blinking green
The port is receiving or sending traffic at a rateof
1000Mbps.
1.6 RG-ES124GD
Technical Specifications
Model
RG-ES124GD
Ports
Twenty-four 10/100/1000Base-Tauto-sensingEthernetports
Power Supply
AC input
Rated voltage range: 100V AC to 240 V AC
Maximum voltage range: 90V AC to 264 V AC
Frequency: 50/60 Hz
Rated current: 0.5 A
EEE
Not supported
PoE
Not supported
Power
Consumption
16 W
Operating
Temperature
0°C to 45°C (32°Fto 113°F)
Storage
Temperature
-40°C to +70°C (-40°F to +158°F)
Operating Humidity
10%to 90%RH
Storage Humidity
5% to 95% RH
Port Mode
Switchover in four modes:
1. Flow Control On
2. Flow Control Off
3. Port Isolation
When portisolation is enabled,ports 1-22 areisolated from eachother, butcancommunicate
with ports 23and 24.
4. ExtendData Transmission-10Mbps:Whenthis modeis enabled,ports 1–8haveareduced
speed of 10Mbps,with atransmission distance of up to250 m. Ifcompatibilityis considered,
some ports maynot deliversuch a transmission distance.
Fan
Not supported
Temperature
Warning
Not supported