Ruijie Reyee RG-ES106D-P V2 Installation and operating manual

Ruijie Reyee RG-ES106D-P V2 Switch
Hardware Installation and Reference Guide
Document Version: V1.1
Date: 2022-11-29
Copyright © 2022 Ruijie Networks

Copyright
Ruijie Networks©2022
Ruijie Networks reserves all copyrights of this document.
Any reproduction, excerption, backup, modification, transmission, translation or commercial use of this
document or any portion of this document, in any form or by any means, without the prior written consent of
Ruijie Networks is prohibited.
Trademarks including , and are
owned by Ruijie Networks.
All other trademarks or registered trademarks mentioned in this document are owned by their respective owners.
Disclaimer
The products, services or features you purchase are subject to commercial contracts and terms. Some or all of
the products, services or features described in this document may not be within the scope of your purchase or
use. Unless otherwise agreed in the contract, Ruijie Networks does not make any express or implied statement
or guarantee for the content of this document.
Due to product version upgrades or other reasons, the content of this document will be updated from time to
time. Ruijie Networks reserves the right to modify the content of the document without any notice or prompt.
This manual is for reference only. Ruijie Networks endeavors to ensure content accuracy and will not shoulder
any responsibility for losses and damages caused due to content omissions, inaccuracies or errors.

I
Preface
Intended Audience
This document is intended for:
Network engineers
Technical support and servicing engineers
Network administrators
Technical Support
The official website of Ruijie Reyee: https://www.ruijienetworks.com/products/reyee
Conventions
1. Signs
The symbols used in this document are described as follows:
Danger
An alert that calls attention to safety operation instructions that if not understood or followed when operating
the device can result in physical injury.
Warning
An alert that calls attention to important rules and information that if not understood or followed can result in
data loss or equipment damage.
Caution
An alert that calls attention to essential information that if not understood or followed can result in function
failure or performance degradation.
Note
An alert that contains additional or supplementary information that if not understood or followed will not lead to
serious consequences.
Specification
An alert that contains a description of product or version support.
2. Note
This manual provides the device installation steps, hardware troubleshooting, module technical specifications,
and specifications and usage guidelines for cables and connectors. It is intended for the users who have some
experience in installing and maintaining network hardware. At the same time, it is assumed that the users are
already familiar with the related terms and concepts.

Contents
Preface.................................................................................................................................................. I
1 Product Overview..............................................................................................................................1
1.1 Package Contents......................................................................................................................1
1.2 Appearance................................................................................................................................1
1.2.1 Front Panel.....................................................................................................................2
1.2.2 Rear Panel.....................................................................................................................3
1.3 Technical Specifications............................................................................................................3
1.4 Cooling.......................................................................................................................................5
2 Preparing for Installation...................................................................................................................6
2.1 Safety Precautions.....................................................................................................................6
2.1.1 General Safety Precautions...........................................................................................6
2.1.2 Handling Safety..............................................................................................................6
2.1.3 Electric Safety................................................................................................................6
2.1.4 Electrostatic Discharge Safety.......................................................................................7
2.2 Installation Environment Requirements.....................................................................................7
2.2.1 Bearing Requirements...................................................................................................7
2.2.2 Ventilation Requirements...............................................................................................7
2.2.3 Space Requirements.....................................................................................................8
2.2.4 Temperature and Humidity Requirements.....................................................................8
2.2.5 Cleanliness Requirements.............................................................................................8
2.2.6 Grounding Requirements...............................................................................................9
2.2.7 Anti-interference Requirements...................................................................................10
2.2.8 Lightning Protection Requirement...............................................................................10

2.2.9 Installation Site Requirements.....................................................................................10
2.3 Tools ........................................................................................................................................10
3 Installing the Switch ........................................................................................................................ 11
3.1 Before You Begin.....................................................................................................................11
3.2 Precautions..............................................................................................................................11
3.3 Mounting the Switch ................................................................................................................12
3.3.1 Mounting the Switch on a Wall ....................................................................................12
3.3.2 Mounting the Switch on a Workbench.........................................................................12
3.4 Grounding the Switch ..............................................................................................................13
3.4.1 Connecting Cables.......................................................................................................13
3.5 Checking after installation........................................................................................................13
4 Verifying Operating Status .............................................................................................................. 14
4.1 Powering on the Switch...........................................................................................................14
4.1.1 Checklist before Power-on...........................................................................................14
4.1.2 Checklist after Power-on..............................................................................................14
5 Appendix..........................................................................................................................................15
5.1 Connectors and Media.............................................................................................................15
5.2 Lightning Protection.................................................................................................................16
5.2.1 Installing AC Power Arrester (lightning protection cable row) .....................................16
5.2.2 Installing the Ethernet Port Arrester.............................................................................17

Hardware Installation and Reference Guide Product Overview
1
1 Product Overview
RG-ES106D-P V2 is a 100M Ethernet PoE switch, providing six 10/100 Mbps self-adaptive Ethernet RJ45 ports
with line-rate forwarding performance. As four ports are PoE-capable and are backward compliant with
IEEE802.3at standard, the RG-ES106D-P V2 can serve as a PoE device. The switch can automatically identify
the powered devices compliant with IEEE802.3at/af standard and supply power for such devices through
Ethernet cables. You can switch the working mode by toggling the DIP switch on the front panel for flow control
and port isolation.
The RG-ES106D-P V2 switch features easy operation and plug-and-play without any configuration. It can work
with more video monitoring devices and access points without being limited by the electric wring. The switch is
an ideal choice for the small- and medium-sized Ethernet.
1.1 Package Contents
Table 1-1 Package Contents
Item
Quantity
RG-ES106D-P V2 Switch
1
Power Adapter (1.2 m/3.94 ft)
1
KA3 x 25 mm Screw
2
Expansion Anchor
2
User Manual
1
Note
The package contents are subject to the purchase contract. The actual delivery prevails. Please check the items
carefully against the package contents or purchase contract. If you have any questions or there are any errors,
please contact your distributor.
1.2 Appearance
The RG-ES106D-P V2 switch provides six 10/100Base-TX self-adaptive Ethernet ports, a DIP switch, a system
LED and other LEDs on the front panel and a DC input plug as well as a grounding stud on the rear panel.

Hardware Installation and Reference Guide Product Overview
2
Figure 1-2 Appearance of a RG-ES106D-P V2 Switch
1.2.1 Front Panel
Figure 1-3 Front Panel of a RG-ES106D-P V2 Switch
1 2 3 4 5
Table 1-2 Front Panel Specifications
No.
Item
Description
1
System Status LED
Off: The device is not powered on.
Solid on: The device is powered on.
2
DIP Switch
The DIP switch is used to switch the working mode.
Standard mode: Flow control is enabled and all ports can
communicate with each other.
Flow Control Off mode: Flow control is disabled and all ports can
communicate with each other. .
VLAN mode: Ports 1 to 4 cannot communicate with each other but
they can communicate with ports 5 and 6.
3
10/100Base-T Self-adaptive
Ethernet Ports
Six 10/100M self-adaptive Ethernet RJ45 ports (Auto MDI/MDIX).
Ports 1-4 are PoE-capable.
4
10/100Base-T Link/Act LED
(1-6)
Solid green: The port has made a successful 10/100 Mbps link
Blinking green: The port is sending and receiving traffic at 10/100

Hardware Installation and Reference Guide Product Overview
3
Mbps.
Off: The port is not connected.
5
PoE LED
Solid green: PoE is enabled.
Blinking green: PoE overload occurs.
Off: PoE is disabled.
1.2.2 Rear Panel
Figure 1-4 Rear Panel of a RG-ES106D-P V2 Switch
Table 1-3 Rear Panel Specifications
No.
Item
Description
1
Grounding Stud
Connect the grounding stud to the protection ground with the grounding
cable to provide grounding protection.
2
Nameplate
Nameplate on the bottom of the device
3
DC Input Plug
Connect the DC power adapter to the DC input plug to power on the
switch.
1.3 Technical Specifications
Table 1-4 Technical Specifications of a RG-ES106D-P V2 Switch
Model
RG-ES106D-P V2
Ports
Six 10/100 Mbps self-adaptive Ethernet ports (Auto MDI/MDIX).
Ports 1-4 are PoE-capable.
Power Supply
AC input:
Rated voltage range: 100 V AC to 240 V AC
Maximum voltage range: 90 V AC to 264 V AC
Frequency: 50 Hz/60 Hz
Rated current: 1.5 A
1 32

Hardware Installation and Reference Guide Product Overview
4
DC output:
Rated voltage: 54 V DC
Rated current: 1.11 A
Dimensions of a DC connector: outer diameter: 5.5 mm (0.22 in.), inner diameter:
2.1 mm (0.08 in.), depth: 10 mm (0.39 in.)
EEE
Disabled by default
PoE
Compliant with IEEE 802.af/at
Ports 1-4 are PoE/PoE+ capable.
Maximum PoE+ output power per port: 30 W
Maximum PoE/PoE+ output power per device: 54 W
PoE Power Cable
Pairs
Mode A (1-2, 3-6 pairs)
Maximum Power
Consumption
60.6 W
Working Mode
Standard mode: Flow control is enabled and all ports can communicate with each
other.
Flow Control Off mode: Flow control is disabled and all ports can communicate
with each other.
VLAN mode: Ports 1 to 4 cannot communicate with each other but they can
communicate with ports 5 and 6.
Operating
Temperature
0ºC to 45ºC (32ºF to 113 ºF)
Storage Temperature
–40ºC to 70ºC (–40ºF to 158ºF)
Operating Humidity
10% to 90% RH (non-condensing)
Storage Humidity
5% to 95% RH (non-condensing)
Lightning Protection
(Port Surge)
4 KV
Fan
Fanless design
Certification
CE
Ground Leakage
Current
≤3.5 mA
Dimensions
(W x D x H)
140 mm x 67 mm x 26 mm (5.51 in. x 2.64 in. x 1.02 in.)
Weight
0.75 kg (1.65 lbs, with packaging materials)
Warning
Operation of this equipment in a residential environment could cause radio interference.

Hardware Installation and Reference Guide Product Overview
5
1.4 Cooling
The RG-ES106D-P V2 switch adopts natural heat dissipation without fans. Please maintain a minimum
clearance of 100 mm (3.94 in.) around the device to ensure normal operation. Dust the device every three
months to avoid blocking the ventilation openings.