Ruijie RG-AP680-IO Installation and operating manual

Ruijie RG-AP680-IO Access Point
Hardware Installation and Reference Guide
Document Version: V1.1
Date: August 16, 2023
Copyright © 2023 Ruijie
Networks

Copyright
Copyright © 2023 Ruijie Networks
All rights are reserved in this document and this statement.
Any reproduction, excerption, backup, modification, transmission, translation or
commercial use of this document or any portion of this document, in any form or by any
means, without the prior written consent of Ruijie Networks is prohibited.
Trademark and are owned by Ruijie
Networks.
All other trademarks or registered trademarks mentioned in this document are owned by
their respective owners.
Disclaimer
The products, services, or features you purchase are subject to commercial contracts and
terms. Some or all of the products, services or features described in this document may
not be within the scope of your purchase or use. Unless otherwise agreed in the contract,
Ruijie Networks does not make any express or implied statement or guarantee for the
content of this document.
Due to product version upgrades or other reasons, the content of this document will be
updated from time to time. Ruijie Networks reserves the right to modify the content of
the document without any notice or prompt.
This manual is for reference only. Ruijie Networks endeavors to ensure content accuracy
and will not shoulder any responsibility for losses and damages caused due to content
omissions, inaccuracies or errors.

I
Preface
Intended Audience
This document is intended for:
Network engineers
Technical support and servicing engineers
Network administrators
Technical Support
Ruijie Networks Website: https://www.ruijienetworks.com/
Technical Support Website: https://ruijienetworks.com/support
Case Portal: https://caseportal.ruijienetworks.com
Community: https://community.ruijienetworks.com
Technical Support Email: [e-mail]
Live Chat: https://www.ruijienetworks.com/rita
Conventions
1. Signs
The signs used in this document are described as follows:
Warning
An alert that calls attention to important rules and information that if not understood or
followed can result in data loss or equipment damage.
Caution
An alert that calls attention to essential information that if not understood or followed
can result in function failure or performance degradation.
Note
An alert that contains additional or supplementary information that if not understood or
followed will not lead to serious consequences.

II
Specification
An alert that contains a description of product or version support.
2. Note
The manual offers configuration information (including model, port type and command
line interface) for indicative purpose only. In case of any discrepancy or inconsistency
between the manual and the actual version, the actual version prevails.

i
Contents
Preface.................................................................................................................................................. I
1 Product Introduction....................................................................................................................... 1
1.1 Overview ...................................................................................................................................1
1.2 Product Appearance ................................................................................................................2
1.3 Package Contents.....................................................................................................................4
1.4 Technical Specifications...........................................................................................................5
1.4.1 Dimensions and Weight...............................................................................................5
1.4.2 RF Specifications...........................................................................................................6
1.4.3 Port Specifications........................................................................................................8
1.4.4 Power Supply and Consumption ................................................................................9
1.4.5 Environment and Reliability ......................................................................................10
1.5 LED and Button.......................................................................................................................10
1.6 Optical Module .......................................................................................................................12
2 Preparing for Installation.............................................................................................................. 14
2.1 Safety Precautions..................................................................................................................14
2.1.1 General Safety Precautions .......................................................................................14
2.1.2 Handling Safety ..........................................................................................................14
2.1.3 Electric Safety..............................................................................................................15
2.1.4 Storage Security .........................................................................................................15

ii
2.2 Installation Environment Requirements..............................................................................15
2.2.1 Bearing Requirements...............................................................................................16
2.2.2 Ventilation Requirements..........................................................................................16
2.2.3 Space Requirements ..................................................................................................16
2.2.4 Temperature/Humidity Requirements.....................................................................16
2.2.5 Grounding Requirements..........................................................................................17
2.2.6 Anti-interference Requirements ...............................................................................17
2.2.7 Lightning Protection Requirements .........................................................................18
2.2.8 Waterproof Requirements.........................................................................................18
2.2.9 Other Requirements ..................................................................................................19
2.3 Tools ........................................................................................................................................20
3 Installation ..................................................................................................................................... 21
3.1 Installation Procedure ...........................................................................................................21
3.2 Before You Begin....................................................................................................................22
3.3 Precautions.............................................................................................................................22
3.4 Installing the Device...............................................................................................................23
3.4.1 Installing the Support for Wall-mounted Installation.............................................23
3.4.2 Installing the Support for Pole-mounted Installation.............................................23
3.4.3 Mounting Bracket and Device Installation...............................................................24
3.4.4 Removing the Device .................................................................................................27
3.5 Installing an Optical Module .................................................................................................27

iii
3.6 Connecting Cables .................................................................................................................28
3.6.1 Connecting the Ground Cable...................................................................................28
3.6.2 Connecting the Network Cable .................................................................................29
3.6.3 Connecting the Fiber-Optic Cable.............................................................................30
3.7 Bundling Cables......................................................................................................................31
3.7.1 Precautions .................................................................................................................31
3.7.2 Bundling Description .................................................................................................32
3.8 Installation Verification..........................................................................................................32
3.8.1 Checking the AP..........................................................................................................32
3.8.2 Checking Cable Connections.....................................................................................33
3.8.3 Checking the Power Supply.......................................................................................33
4 Verifying Operating Status ........................................................................................................... 34
4.1 Establishing the Configuration Environment ......................................................................34
4.2 Powering on the AP................................................................................................................34
4.2.1 Checklist Before Power-on ........................................................................................34
4.2.2 Checking the Environment After Power-on .............................................................34
5 Monitoring and Maintenance....................................................................................................... 35
5.1 Monitoring ..............................................................................................................................35
5.1.1 LED...............................................................................................................................35
5.1.2 CLI Commands ...........................................................................................................35
5.2 Remote Maintenance.............................................................................................................35

iv
5.3 Hardware Maintenance .........................................................................................................35
6 Troubleshooting ............................................................................................................................ 36
6.1 General Troubleshooting Procedure....................................................................................36
6.2 Common Troubleshooting Procedures................................................................................36
6.2.1 Ethernet Port Is Not Working After the Ethernet Cable Is Plugged In..................36
6.2.2 LED Is Off for a Long Time.........................................................................................36
6.2.3 LED Is Steady Red.......................................................................................................37
6.2.4 LED Is Steady Green...................................................................................................37
6.2.5 LED Keeps Blinking Blue at an Interval of 0.2s (in Fit Mode)..................................37
6.2.6 LED Does Not Turn Steady Blue or Blinking Blue....................................................37
6.2.7 No Wireless Signal Searched.....................................................................................37
7 Appendix ........................................................................................................................................ 38
7.1 Connectors and Media...........................................................................................................38
7.2 Cabling Recommendations ...................................................................................................41
7.3 Optical Modules and Specifications......................................................................................46

Hardware Installation and Reference Guide Product Introduction
1
1 Product Introduction
1.1 Overview
The RG-AP680-IO is a Wi-Fi 6, dual-radio, enhanced, and industrial wireless access point
(AP) provided by Ruijie Networks for higher education, wireless city, energy, business
mall, and other scenarios.
The RG-AP680-IO supports the 802.11ax, 802.11ac Wave2, 802.11ac Wave1, and 802.11n
protocols. With hardware-independent quad-band design, the AP can provide up to 5.951
Gbps access rate. The ultra-fast wireless network makes performance no longer a
bottleneck.
Important factors such as the wireless network security, radio control, mobile access,
Quality of Service (QoS), seamless roaming, and expansion of the Internet of Things (IoT)
module are fully taken into account for this product. Therefore, this AP can be used in
combination with Ruijie Access Controllers (ACs) and WIS to implement STA data
forwarding, security, access control, and IoT application extension.
Thanks to its IP68 rated housing, the RG-AP680-IO is suitable for use in extreme
industrial environments and capable of effectively withstanding harsh weather and
environments. It is highly adaptable to colder and wet climates, allowing for easier
installation and maintenance.
The RG-AP680-IO supports power over Ethernet (PoE) and built-in omnidirectional
antennas to meet Wi-Fi network coverage and networking requirements in most
environments.

Hardware Installation and Reference Guide Product Introduction
2
1.2 Product Appearance
Figure 1-1Front View
Table 1-1 Description of Buttons and Ports on the Front Panel
No.
Item
Description
1
LAN1/HPoE electrical
port
Uplink service port for data transmission, 5000Base-T
Ethernet port with auto-negotiation
Support IEEE802.3af/802.3at/802.3bt-complaint PoE
2
LAN2/IoT
Downlink service port for data transmission, 1000Base-T
Ethernet port with auto-negotiation
Support 802.3af-complaint power supply to external
devices
3
LAN3/SFP+
Uplink service port for data transmission, 10GE SFP port

Hardware Installation and Reference Guide Product Introduction
3
No.
Item
Description
4
LED
Used to indicate the system working status, including
one system status LED and three RSSI LEDs
Figure 1-2Rear View

Hardware Installation and Reference Guide Product Introduction
4
Table 1-2 Description of Buttons and Ports on the Rear Panel
No.
Item
Description
1
Console port/Reset
button
The port integrates the functions of a console port and a
reset button.
The console port is used to connect with a serial
cable for device management.
The Reset button is used to restart a device or
restore factory settings of the device.
2
Grounding stud
Used to ground the AP.
3
Breathable valve
Used to balance the pressure difference inside and
outside the AP, meeting IP68 rating requirements
1.3 Package Contents
Table 1-3 Package Contents
No.
Item
Quantity
Remarks
1
AP
1
2
Mounting bracket
1
3
Support for pole-mounted or
wall-mounted installation
1
4
M5 x 10 machine screw
4
5
M6 x 16 machine screw
2
6
M8 x 20 machine screw
2
7
M6 x 40 expansion anchor
4
8
Waterproof PG connector
2
The rubber plug only has one
hole and adapts to network

Hardware Installation and Reference Guide Product Introduction
5
No.
Item
Quantity
Remarks
cables with a diameter of 6.6 to
8.6 mm.
9
Waterproof connector for the
fiber-optic cable
1
The rubber plug has two holes
and adapts to LC-LC fiber-optic
cables with a diameter of 2.5 to
3.5 mm.
10
Metal hook
2
Adapts to poles with a diameter
of 80 to 140 mm
11
Ground cable
1
12
Product warranty manual
1
13
Dust cap for ports
4
The dust caps are pre-installed on
the AP.
14
User Manual
1
1.4 Technical Specifications
1.4.1 Dimensions and Weight
Table 1-4 Dimensions and Weight
Dimensions and
Weight
RG-AP680-IO
Dimensions (W × D
× H)
300 mm × 300 mm × 94 mm (11.81 in. x 11.81 in. x 3.70 in.)
Weight
Main unit: 4.0 kg (8.82 lbs)
Mounting bracket: 1.5 kg (3.31 lbs)
Installation
Wall-mounted or pole-mounted

Hardware Installation and Reference Guide Product Introduction
6
Dimensions and
Weight
RG-AP680-IO
Mounting bracket
Dimensions (W x D
x H)
130 mm × 282 mm x 130 mm (5.12 in. x 11.10 in. x 5.12 in.)
Mounting hole
pattern
105 mm × 65 mm (4.13 in. x 2.56 in.)
Mounting hole
diameter
9 mm (0.35 in.)
Pole diameter
80 mm to 140 mm (3.15 in to 5.51 in.)
1.4.2 Radio Specifications
Table 1-5 Radio Specifications
Radio
Specifications
RG-AP680-IO
Radio design
Dual-radio, eight spatial streams
Radio 1: 2.4 GHz, 4 spatial streams: 4x4, MIMO
Radio 2: 5 GHz, 4 spatial streams: 4x4, MIMO
Operating
frequencies
Radio 1: 802.11b/g/n/ax, 2.400 to 2.4835 GHz
Radio 2: 802.11a/n/ac/ax, 5.150 GHz to 5.350 GHz, 5.470 GHz to
5.725 GHz, 5.725 to 5.850 GHz
Note: The operating frequency is country-specific.
Data rate
Radio 1: 2.4 GHz, 1.147 Gbps
Radio 2: 5 GHz, 4.804 Gbps
Combined: 2.4 GHz + 5 GHz, 5.951 Gbps
Antenna type
Built-in smart antenna

Hardware Installation and Reference Guide Product Introduction
7
Radio
Specifications
RG-AP680-IO
Antenna gain
2.4 GHz: 3 dBi
5 GHz: 3 dBi
Max. transmit
power
30 dBm
Note: The transmit power varies based on the regulations in
different countries and regions.
Power increment
1 dBm
Modulation
OFDM: BPSK@6/9 Mbps, QPSK@12/18 Mbps, 16-QAM@24 Mbps,
64-QAM@48/54 Mbps
DSSS: DBPSK@1 Mbps, DQPSK@2 Mbps, and [email protected]/11 Mbps
MIMO-OFDM: BPSK, QPSK, 16QAM, 64QAM, 256QAM, and
1024QAM
OFDMA
Receive sensitivity
802.11b: –96 dBm (1 Mbps), –93 dBm (5 Mbps), –89 dBm (11 Mbps)
802.11a/g: –91 dBm (6 Mbps), –85 dBm (24 Mbps), –80 dBm (36
Mbps), –74 dBm (54 Mbps)
802.11n: –90 dBm (MCS0), –70 dBm (MCS7), –89 dBm (MCS8), –68
dBm (MCS15)
802.11ac: HT20: –88 dBm (MCS0), –63 dBm (MCS9)
802.11ac: HT40: –85 dBm (MCS0), –60 dBm (MCS9)
802.11ac: HT80: –85 dBm (MCS0), –60 dBm (MCS9)
802.11ac: HT160: –80 dBm (MCS0), –55 dBm (MCS9)
802.11ax: HE80: –82 dBm (MCS0), –57 dBm (MCS9), –52 dBm
(MCS11)
802.11ax: HE160: –80 dBm (MCS0), –49 dBm (MCS11)

Hardware Installation and Reference Guide Product Introduction
8
1.4.3 Port Specifications
Table 1-6 Port Specifications
Port Specifications
RG-AP680-IO
Bluetooth
Bluetooth 5.1
The Bluetooth serial port management mode is used by default.
Apple iBeacon protocol is supported, through which rich
Bluetooth applications such as shake can be extended.
Support for the Zigbee, RFID, and other IoT protocols via software
upgrade
Fixed service port
Uplink:
One 100/1000/2500/5000Base-T Ethernet port with auto-
negotiation, supporting IEEE 802.3af/at/bt-compliant PoE
Two 10 Gbps SFP+ Ethernet optical ports with auto-negotiation,
which are compatible with 2.5 Gbps/1 Gbps optical ports
Downlink:
One 10/100/1000Base-T Ethernet port with auto-negotiation,
which allows the PSE to power external devices (802.3af, 15.4 W)
and can connect to Ruijie IoT module
Fixed management
port
One RJ45 console port
Status LED
One system status LED
Three RSSI LEDs
Button
One reset hole
GPS
Supported

Hardware Installation and Reference Guide Product Introduction
9
1.4.4 Power Supply and Consumption
Table 1-7 Power Supply and Consumption
Power Supply and
Consumption
RG-AP680-IO
Input power supply
DC power supply (48 V/0.35 A)
PoE/PoE+/PoE++ (IEEE 802.3af/at/bt-compliant)
Note: If the AP is powered by 802.3af PoE, only the CPU works. If
the AP is powered by 802.3at PoE, Radio 3 does not work and the
AP does not supply power to external devices.
External power
supply
Supported (Connect to Ruijie IoT module, 802.3af-compliant,
support for 15.4 W output power)
Max. power
consumption
≤40 W
Caution
To power the AP by using PoE, ensure that the device at the other end of the
Ethernet cable supports IEEE 802.3af power supply.
In 802.3af power supply state, the device can be started properly. All RF cards do not
work, and the PSE does not power external devices.
In 802.3at power supply state, the PSE does not power external devices.
In 802.3bt power supply state, the device has the highest performance and all
functions are enabled.
The AP adopts a fan-free design. Therefore, maintain sufficient clearance around the
AP for air circulation.

Hardware Installation and Reference Guide Product Introduction
10
1.4.5 Environment and Reliability
Table 1-8 Standard Compliance
Environment and
Reliability
RG-AP680-IO
Temperature
Working temperature: –40°C to +65°C (–40°F to +149°F)
Storage temperature: –40°C to +85°C (–40°F to +185°F )
At a height between 3000 m (9842.52 ft.) and 5000 m (16404.2 ft.),
every time the altitude increases by 166 m (546 ft.), the maximum
temperature decreases by 1°C (1.8°F).
Humidity
Operating humidity: 0% to 100% RH (non-condensing)
Storage humidity: 0% to 100% RH (non-condensing)
IP Rating
IP68
Anti-corrosion rating
GB/T 2423.17
Regulatory
compliance
EN 55032, EN 55035, EN 61000-3-3, EN IEC 61000-3-2, EN 301 489-
1, EN 301 489-3, EN 301 489-17, EN 300 328, EN 301 893, EN 300
440, FCC Part 15, EN IEC 62311, IEC 62368-1, EN 62368-1, and IEC
60950-22
1.5 LED and Button
Note
The LED description applies to both fit and fat modes unless otherwise specified.
Table 1-9 LED Status
Status
Frequency
Description
Off
N/A
The AP is not powered on.
The AP is powered on, but the LED is manually

Hardware Installation and Reference Guide Product Introduction
11
Status
Frequency
Description
turned off.
Steady green
N/A
The software system of the AP is being
initialized.
Steady red
N/A
The system is running properly, but the uplink
service port is linked down.
Blinking red at
an interval of 1s
On for 3s
Off for 1s
In fit mode, the setup of a CAPWAP tunnel
between the AP and AC timed out.
Blinking blue at
an interval of
0.2s
On for 0.2s
Off for 0.2s
In fit or MACC mode, the software system of
the AP is being updated.
Steady blue
N/A
The system is running properly, but there is
no STA online.
Blinking blue at
an interval of 1s
On for 1s
Off for 1s
The system is running properly and there are
one or more STAs online.
Blinking red at
an interval of
0.2s
On for 0.2s
Off for 0.2s
In fit mode, the AP is being located.
Table 1-10 Reset button
Button
Operation
Result
Reset button
Press the button for
less than 2s
Reboot the device.
Press and hold the
button for longer
than 5s
Restore to factory settings.

Hardware Installation and Reference Guide Product Introduction
12
Table 1-11 Bridge LED
LED Color
No. of Steady-
on LED
Description
N/A
N/A
The AP does not enable the bridge function.
The AP has enabled the bridge function, but bridging fails.
Green
1
Bridging is successful, and the strength of the wireless
signals dedicated for bridging is less than –70 dBm.
Green
1, 2
Bridging is successful, and the strength of the wireless
signals dedicated for bridging ranges from –70 dBm to –50
dBm.
Green
1, 2, 3
Bridging is successful, and the strength of the wireless
signals dedicated for bridging is greater than –50 dBm.
1.6 Optical Module
The type of the port on the device directly connected with the 10G SFP port on the AP can
be an optical port or electrical port. However, the negotiated rate varies depending on
the port rate or optical module used on both devices. For details, see Table 1-11 and
Table 1-12.
Table 1-12 Rate Negotiation for an Optical Port on the Peer Device
Optical
Port Rate
of the AP
Optical
Module Rate
Negotiated Rate Supported by the Port on the Peer
Device
1 Gbps
1 Gbps/10
Gbps/Auto
1 Gbps/2.5 Gbps/10
Gbps/Auto
10 Gbps
10 Gbps
1 Gbps
10 Gbps
10 Gbps
10 Gbps
2.5 Gbps
Not supported
Not supported
2.5 Gbps
10 Gbps
1 Gbps
1 Gbps
1 Gbps
1 Gbps