Ruijie Reyee RG-RAP6202(G) Installation and operating manual

Ruijie Reyee RG-RAP6202(G) Access Point
Hardware Installation and Reference Guide
Document Version: V1.0
Date: 2022-07-20
Copyright © 2022 Ruijie Networks

Copyright
Ruijie Networks©2022
Ruijie Networks reserves all copyrights of this document.
Any reproduction, excerption, backup, modification, transmission, translation or commercial use of this
document or any portion of this document, in any form or by any means, without the prior written consent of
Ruijie Networks is prohibited.
Trademarks including, and are owned by Ruijie Networks.
All other trademarks or registered trademarks mentioned in this document are owned by their respective owners.
Disclaimer
The products, services or features you purchase are subject to commercial contracts and terms. Some or all of
the products, services or features described in this document may not be within the scope of your purchase or
use. Unless otherwise agreed in the contract, Ruijie Networks does not make any express or implied statement
or guarantee for the content of this document.
Due to product version upgrades or other reasons, the content of this document will be updated from time to
time. Ruijie Networks reserves the right to modify the content of the document without any notice or prompt.
This manual is for reference only. Ruijie Networks endeavors to ensure content accuracy and will not shoulder
any responsibility for losses and damages caused due to content omissions, inaccuracies or errors.

I
Preface
Intended Audience
This document is intended for:
⚫Network engineers
⚫Technical support and servicing engineers
⚫Network administrators
Technical Support
⚫Official website of Ruijie Reyee: https://www.ruijienetworks.com/products/reyee
⚫Technical Support Website: https://ruijienetworks.com/support
⚫Case Portal: https://caseportal.ruijienetworks.com
⚫Community: https://community.ruijienetworks.com
⚫Technical Support Email: [email protected]
Conventions
1. Signs
The symbols used in this document are described as follows:
Danger
An alert that calls attention to safety operation instructions that if not understood or followed when operating the
device can result in physical injury.
Warning
An alert that calls attention to important rules and information that if not understood or followed can result in
data loss or equipment damage.
Caution
An alert that calls attention to essential information that if not understood or followed can result in function
failure or performance degradation.
Note
An alert that contains additional or supplementary information that if not understood or followed will not lead to
serious consequences.
Specification
An alert that contains a description of product or version support.

II
2. Note
This manual provides the device installation steps, hardware troubleshooting, module technical specifications,
and specifications and usage guidelines for cables and connectors. It is intended for the users who have some
experience in installing and maintaining network hardware. At the same time, it is assumed that the users are
already familiar with the related terms and concepts.

I
Contents
Preface................................................................................................................................................I
1 Product Overview..........................................................................................................................3
1.1 Package Contents .................................................................................................................3
1.2 Appearance ...........................................................................................................................4
1.3 Technical Specifications .......................................................................................................7
1.4 Power Supply ........................................................................................................................8
2 Preparing for Installation.............................................................................................................. 9
2.1 Safety Precautions ................................................................................................................9
2.1.1 Grounding and Lightning Protection ......................................................................9
2.2 Preparing the Installation Site .............................................................................................9
2.2.1 Temperature and humidity requirements .............................................................10
2.2.2 Outdoor Installation................................................................................................ 10
2.2.3 Weatherproof ..........................................................................................................10
2.2.4 EMI............................................................................................................................10
2.3 Installation Tools................................................................................................................. 11
3 Installation ...................................................................................................................................12
3.1 Installation Flowchart .........................................................................................................12

II
3.2 Before You Begin ................................................................................................................ 12
3.3 Choosing a Site ...................................................................................................................12
3.4 Installing the Device ........................................................................................................... 13
3.4.1 Wall Mounting......................................................................................................... 13
3.4.2 Vertical Pole Mounting ...........................................................................................14
3.4.3 Horizontal Pole Mounting......................................................................................15
3.5 Connecting Ethernet Cables .............................................................................................. 16
4 Appendix Connectors and Media..............................................................................................18

Hardware Installation Guide and Reference Product Overview
3
1 Product Overview
The RG-RAP6202(G) access point is an outdoor wireless access point designed by Ruijie Networks for high-
speed wireless networks. RAP6202(G) features wireless network security, radio frequency (RF) control, mobile
access, Quality of Service (QoS) and seamless roaming.
The IP68 design adapts to inclement outdoor environments such as the cold and humidity, and can effectively
avoid the influence of bad weather and environment. This greatly simplifies installation and maintenance.
RAP6202(G) supports PoE and can be applied in a wide variety of deployment scenarios, including outdoor space
of hotels, orchard monitoring, warehouses.
1.1 Package Contents
Table 1-1 Package Contents
Item
Quantity
RG-RAP6202(G) Access Point
1
Hardware Installation and Reference Guide
1
Hose Clamp
2
Mounting Plate
1
M8 x 60 Expansion Bolt
4
M8 x 20 Screw
2
Cable Gland (Pre-installed on the AP)
2
Connecting Rod (Pre-installed on the AP)
1
Warranty Card
1
Note
A normal delivery should contain the above mentioned items, which may differ from the actual delivery, depending
on purchase contracts. Please check your goods carefully against the package contents list or purchase contract.
If you have any questions or there are any errors, please contact your distributor.

Hardware Installation Guide and Reference Product Overview
4
1.2 Appearance
Figure 1-1 Front View
Figure 1-2 Side View

Hardware Installation Guide and Reference Product Overview
5
Figure 1-3 Ports
Table 1-2 Description
Sign
Button/Port
Function
1
Ethernet Port
10/100/1000Base-T adaptive Ethernet ports
2
Power port
DC power port, 12 V/1.5 A
Caution
If the power adapter is needed, please purchase it separately.
3
Ethernet port/PoE
10/100/1000 Base-T adaptive Ethernet ports, supporting 802.3af/802.3at PoE
power supply
4
Reset button
Press for shorter than 2 seconds: Restart the device.
Press for 2 to 5 seconds: There is no reaction on the device.
Press for longer than 5 seconds: Restore the factory settings.
5
Weatherproof Cap
Protect the access point interior from environmental elements including water,
heat, cold, and dust.

Hardware Installation Guide and Reference Product Overview
6
Figure 1-4 Top View
Table 1-3 Description
LED
Status
Meaning
Wi-Fi (Green)
Blinking
Data is transmitted by Wi-Fi.
Solid on
Wi-Fi is enabled and no data is transmitted.
Off
Wi-Fi is disabled.
SYS(Blue)
Fast blinking
The device is being initialized.
Slow blinking (0.5 Hz):
The Internet is unreachable.
Blinking twice
1. Restore the factory settings.
2. Upgrade the firmware and restore the image file.
Caution
In this case, please do not power off the device.

Hardware Installation Guide and Reference Product Overview
7
LED
Status
Meaning
A long blink and three
short blinks
Other faults occur.
Solid on
The device is working properly without alarm.
Off
The device is powered off.
LAN 1(Green)
Blinking
The port is up and data is transmitted.
Solid on
The port is up and no data is transmitted.
Off
The port is down.
LAN 2(Green)
Blinking
The port is up and data is transmitted.
Solid on
The port is up and no data is transmitted.
Off
The port is down.
1.3 Technical Specifications
Table 1-4 Technical Specifications of RG-RAP6202(G)
Max Transmission Rate
Built-in antenna mode: 1267Mbps (867Mbps@5GHz ; [email protected])
Operating Frequency
802.11b/g/n: 2.4 GHz to 2.4835 GHz
802.11a/n/ac: 5.150 GHz to 5.350 GHz, 5.47 GHz to 5.725 GHz, 5.725 GHz to
5.850 GHz
(Country-Specific)
Transmit Power
2.4 GHz: ≤ 26 dBm(adjustable)
5 GHz: ≤ 27 dBm(adjustable)
Antenna Type
Built-in omnidirectional antennas
Antenna Gain
2.4 GHz: 3dBi
5 GHz: 4dBi
Beam Width
2.4 GHz E: 30°; H: 360°
5 GHz E: 30°; H: 360°
Ports
One 10/100/1000BASE-T Ethernet uplink port supports 802.3af/ 802.3at PoE
input.
One 10/100/1000 Base-T Ethernet port
FAT/FIT Mode Switchover
Not Supported
Power Supply
IEEE 802.af/at PoE
DC power port: 12 V/1.5 A

Hardware Installation Guide and Reference Product Overview
8
Caution
If the power adapter is needed, please purchase it separately.
Power Consumption
< 12.95 W
LED
System, Wi-Fi and port status indicators
Product Certification
CE
ROHS
Dimensions (W x D x H)
222 mm × 200 mm × 166 mm (8.74 in. x 7.87 in. x 6.54 in.)
Weight
< 1 kg (2.20 lbs.)
IP Rating
IP68
Operating Temperature
-30°C to 65°C (-22°F to 149°F)
Operating Humidity
0% to 100% (non-condensing)
Storage Temperature
-40°C to 85°C (-40°F to 185°F)
Storage Humidity
0% to 100% (non-condensing)
Warning
Using this device may cause radio interference in living environment.
1.4 Power Supply
RG-RAP6202(G) supports 802.3af/802.3at-compliant PoE or 12V DC/1.5 A power supply (please purchase a
power adapter separately).
Table 1-5 Power Supply
Output Voltage
12 V
Minimum Output current
1.5 A
Technical Specifications
of the DC Power
Connector
Inner Diameter: 2.1 mm (0.08 in.)
Outer Diameter: 5.5 mm (0.25 in.)
Depth: 10 mm (0.39 in.)
Polarity:
Inner pole: positive
Outer pole: negative

Hardware Installation Guide and Reference Preparing for Installation
9
2 Preparing for Installation
2.1 Safety Precautions
Note
To prevent device damage and physical injury, please read carefully the safety recommendations described
in this chapter.
The following safety precautions do not cover all possible dangers.
Warning
Using this device may cause radio interference in living environment.
2.1.1 Grounding and Lightning Protection
⚫Keep the grounding connection within 30 m (98.43ft), and use a 40 mm x 4 mm (1.57 in. x 0.16 in.) or 50 mm
x 5 mm (1.97 in. x 0.2 in.) ground bar of hot-dip zinc-coated flat steel sheet.
⚫When the connection cable between the main grounding conductor and local equipotential earthing terminal
board (LEB) on each floor is short, use a stranded copper wire with a sectional area not less than 1.318 mm2
(16 AWG) for the connection cable.
⚫Use a shielded network cable and make sure that the devices at the two ends of the cable, and the shielded
sleeves are well grounded. Alternatively, run the network cable through the steel pipe and ground the pipe at
both ends.
⚫No additional lightning protector is required as a high-profile lightning protector is built in the RG-RAP6202(G)
and the antenna port and power port support 4 kV lightning protection. If a lightning protector of a higher profile
is available, configure the lightning protector optionally. Before the configuration, connect the lightning
protector to the ground cable.
⚫Use a power cable with the PE end to ground the power supply (AC). Ensure that the PE end is properly
grounded, with a ground resistance less than 5 ohms. Do not use a two-wire power cable with only the live (L)
wire and naught (N) wire. Do not connect the N wire to the protection ground cable of other communication
devices, and ensure that the L wire and N wire are properly connected.
⚫The ground resistance should be less than 5 ohms. In an area with a higher soil resistivity, reduce the soil
resistance by spreading ground resistance reducer powder to reduce the soil resistivity.
2.2 Preparing the Installation Site
⚫Do not expose the AP to high temperature, dust, or harmful gases.
⚫Do not install the AP in an area prone to fire or explosions.
⚫Keep the AP away from EMI sources such as large radar stations, radio stations, and substations.
⚫Do not subject the AP to unstable voltage, vibration, and noises.

Hardware Installation Guide and Reference Preparing for Installation
10
⚫Keep the AP at least 500 meters away from the ocean and do not face it towards the sea breeze.
⚫The installation site should be protected from water and flooding, seepage, dripping, or condensation.
⚫The installation site should be selected according to network planning, communications equipment features
and considerations such as climate, hydrology, geology, earthquake, electric power, and transportation.
2.2.1 Temperature and humidity requirements
Temperature and Humidity Requirements:
Operating Temperature
Operating Humidity:
-30°C to 65°C (-22°F to 149°F)
0% to 100% RH (non-condensing)
2.2.2 Outdoor Installation
The AP can be installed outdoors and supports installation methods including wall mounting, vertical pole
mounting and horizontal pole mounting.
2.2.3 Weatherproof
⚫Use a weatherproof cap to seal the unused ports.
⚫After using the reset button, please seal it with the weatherproof cap.
⚫The Ethernet cable needs to be threaded through the cable gland before connecting to the AP. For details, see
Chapter 3 Installation.
2.2.4 EMI
All interference sources (from outside or inside of the device or application system) affect the device by capacitive
coupling, inductive coupling, or electromagnetic waves.
Electromagnetic interference (EMI) occurs due to electromagnetic radiation or conduction, depending on the
transmission path.
Radiation interference occurs when energy (usually radio frequency energy) is emitted from a device and
propagated through space to disrupt other devices. The interference source can be part of disrupted system or a
fully electrically isolated unit. Conduction interference occurs when interference is transferred from one unit to
another through cables, which are usually electromagnetic wires or signal cables connected between the source
and the device(s) experiencing interference. Conduction interference often affects the power supply of the device.
It is eliminated by using filters. Radiation interference can influence the path of any signal from the device and is
difficult to shield.
⚫Take effective measures against interference from the power grid.
⚫Keep the AP far away from the grounding or lightning protection devices for power equipment.
⚫Keep the AP away from high-power radio stations, radar stations, and high-frequency high-current devices.
⚫Take electrostatic shielding measures.

Hardware Installation Guide and Reference Preparing for Installation
11
2.3 Installation Tools
Table 2-1 Installation Tools
Common Tools
Marker, Phillips (crosshead) screwdriver, slotted screwdriver, paper knife, diagonal
pliers, wires, Ethernet cables, binding straps, wrench and hammer
Special Tools
Hammer drill, ESD tools, stripping pliers and crimping pliers
Meter
Multimeter, network cable tester
Relevant devices
PC, display, and keyboard
Note
The tool kit and cables are customer-supplied.

Hardware Installation Guide and Reference Installation
12
3 Installation
Caution
Before installing the AP, make sure you have carefully read the requirements described in Chapter 2.
3.1 Installation Flowchart
3.2 Before You Begin
⚫The installation site meets temperature and humidity requirements.
⚫The installation site is equipped with a proper power supply.
⚫Network cables are in place.
3.3 Choosing a Site
The outdoor AP can be mounted on a wall and a pole with a diameter ranging from 50 mm to 70 mm (1.97 in. to
2.76 in.). If the diameter of the pole is out of the range, the hose clamp is customer-supplied. In this case, it is
recommended that you use a hose clamp with thickness of 2.5mm (0.1 in.) at least. The installation site varies
due to on-the-spot surveys conducted by technical personnel.
Please make full preparations as described in Chapter 2 and observe the following precautions before installing

Hardware Installation Guide and Reference Installation
13
the device.
⚫Before connecting the power supply, make sure the external power supply matches the power module of the
AP.
⚫Before connecting the power cord, make sure the power module is turned off.
⚫When connecting the power cord to a binding post, make sure their colors are the same.
⚫Make sure the power supply is properly connected.
3.4 Installing the Device
3.4.1 Wall Mounting
Use the mounting plate and M8 x 60 expansion bolts to implement wall mounting.
a Attach the mounting plate to the wall and mark the locations of screw holes after adjusting the installation
position.
Figure 3-1 Pre-install M8 x 60 expansion bolts on the wall
b Install the access point and the connecting rod to the mounting plate on the wall, and tighten the M8 x 20
screws to complete installation.
Figure 3-2 Wall Mounting

Hardware Installation Guide and Reference Installation
14
3.4.2 Vertical Pole Mounting
Secure the mounting plate to the vertical pole by threading two clamps through the mounting plate, and
fasten the clamps with screws. You are advised to use an electronic screwdriver.
Figure 3-3 Mounting the Plate on a Vertical Pole
Install the access point and the connecting rod to the mounting plate on the vertical pole, and tighten the M8
x 20 screws to complete installation.
Figure 3-4 Vertical Pole Mounting

Hardware Installation Guide and Reference Installation
15
3.4.3 Horizontal Pole Mounting
Note
The procedures of horizontal pole mounting are the same as those of vertical pole mounting.
Figure 3-5 Mounting the Plate on a Horizontal Pole
Figure 3-6 Horizontal Pole Mounting

Hardware Installation Guide and Reference Installation
16
3.5 Connecting Ethernet Cables
Caution
The weatherproof materials are customer-supplied.
(1) Trim an Ethernet cable according to the distance between the access point and the power supply.
(2) Insert the unterminated end of the Ethernet cable through part D, C and B in sequence.
(3) Install an RJ45 connector on the unterminated end of the Ethernet cable using an Ethernet cable installation
tool..
(4) Insert the RJ45 connector into the LAN, PoE or uplink port of the access point, and tighten part B, C and D in
sequence.
(5) If you want to install the cable gland without an Ethernet cable threaded through it, insert the waterproof rubber
rod into the washer (rubber gasket), and tighten part B, C and D in sequence.
(6) Make sure to seal the DC port and the reset button with clean weatherproof caps and insert them into the slot
of connecting rod.
Washer
(Rubber
Gasket)
RJ-45
Connector