Russound A-K3 User manual

A-K3
Amplified Keypad with Multisource Capability
for A-BUS
8
System
Installation Manual
A-K3 Overview
The Russound A-K3 is an in-wall amplified keypad used
with A-BUS hubs and controllers in a distributed audio
system. It can be used with both single- and multi-source
A-BUS hubs/controllers. The A-K3 provides source selec-
tion and control with backlit push buttons, plus an IR
window to receive remote control signals.
The
volume up/down buttons control the speakers in
the room that are connected to the A-K3. Typical installa-
tions place one
A-K3 in each room of the A-BUS system.
The Line
Out connection on the A-K3 can be used to
feed aseparate powered subwoofer or to connect an
external amplifier for more power to alarger listening
area.
A-K3 Key Features
Power On/Off button (acts as source select with
multi-source hubslcontrollers)
Volume trims for
L/R balance and maximum level
settings
Built-in
IR receiver with IR confirmation LED
IR control of settings and sources via A-LRC2 optional
remote
Line Out connection for external
amp or powered
subwoofer
A-K3 Specifications
Output Impedance:
Input Impedance:
Power Requirements:
CAT-5 Connections:
Dimensions (in-wall):
Weight:
8ohmslchannel
(1 pair speakers)
10 kohms
+24VDC 660mA peak
RJ45
1.75"W x2.875"H x1.75"0
(45x73x45mm)
5.5oz. (160g)
A-BUS is aregistered trademark of LeisureTech Electronics Pty
Ltd Australia
This product may be covered by one or more of the following
patents:
US #7,181,023, #6,389,139; EP #1004222,
AU #739808, NZ #502982, Mexico #241196, Canada #CA2301 062

A K3 Keypad Fron Panel Opera ion
'---------I~--4
3 ---oof--------J
1 ----+---+-------.- tJ0
r;;o
2 ----+--+------- @ ...-..---+--6
---------+---5
1 VOLUME UP/DOWN -Raises/ owers room va ume
2 VOLUME LEVEL - Volume evel indicator LEDs light up
from bot om 0 top to idica evol me eve •. Also
'ndicates source selected (-6) wen in "
mu
f-sQurceU
mode.
3 STATUS LED -Green LED lights to S ow 5atus lion" and
turns off when 5atus is lIoff"
4 IR CONFIRMATION LED - Red LED blinks to conflr 'R
signal recep ·on.
IR RECEIVER -Receives Rsigna 5 from a remote
can rol. So rce co po ents atac ed a IR emitters
in an
A-BUS system ca be controlled w"t their own
remote controls or A-LRC2Iea ning re ate aOmed at
the A-K3,
6 POWER -Turns zo e0 when pessed once. (I multi-
sourc,e mode, wen ON, ress and hod wOIl urn zone
OFF. Wen OFF, p ess and adwil turn OFF all zones.)
Sta us Dremains lit when keypad/zone is OFF of any
other zone in sys em is 0 .
6 SOURCE SELEU (Mul· ~ so rce controller) - W. en the
eypad is se in "Multisou. ce" mode, he power bu on
's used to oggle th ough and se eet asource. Tap he
power bu on to ogg e between 1and 6 multiple
sources (once powe is on). Te op LEDs of the volume
id'cator show (fro top to bo tom) the source hat's
selec ed (op ED is source 1, nex LED down is
source 2, etc).

CONNECTION DIAGRAM FOR A-K3. REFER TO THE NUMBERED INSTRUCTIONS ON REVERSE. DIAGRAMS ARE NOT TO SCALE.
, , , . . '-131
••••••••• e·. ~ •.• ',' '" .' .' ••• ", ~~.-_
•• :.:... e. •e!- • e . _:- ~ • e. . e. • .. _ L2:.~
A-C68 (back)
CAT-S
cable
22AWG
2pair
twisted
shielded
cable Speakers
6
4
•
•
•
~tatus [!] []![]
Jumper [!] ~
NO LED
LED
Source
jumper
o
U
o
o
Lj:
/7 ..
V·
.@
.-
@
o
o
@
"'-
,- -
Jr,
G')
/(»J
z
\::IJ"",
A-K3 (side) A-K3 (back)
A-K3 (front)
A-C68 (front)
.. -- ..
"--'-1
• G). '":"·1' ~ -e ••• ,. • •
Speaker cable Keypad Dip
Switches
Keypad dip switch on A-C68
set in DOWN position
8-ohm speakers
RJ-4S using TS68A Wiring Standard
12345678
~ I ~ I ~ I ~ I

CONNECTION INSTRUCTIONS FOR A-K3. REFER TO NUMBERED DIAGRAM ON REVERSE.
1 RJ45 Connector for CAT-5 Connection
The RJ45 input provides aconnection for the CAT-5 cable
from an A-BUS hub/controller to receive an audio signal,
passthrough IR and power over the CAT-5 cable. Use the
T568A wiring standard. The recommended maximum
length for standard CAT-5 cable is 150 feet.
Before connecting the A-K3, disconnect the power sup-
ply from the A-BUS hub/controller and disconnect the
Status power supply if used.
2 Line Out Connector for External Amplification
The Line Out provides avariable line-level audio output
connection for an external amplifier or powered sub-
woofer. An amplifier provides more power to alarge
listening area, and apowered subwoofer adds extended
bass response.
Use 22AWG four conductor, two-pair twisted shielded
cable to connect to the Left positive (+) and negative (-),
and Right positive (+) and negative (-) screw down termi-
nals on the back of the A-K3.
Terminate the four conductor two-twisted pair shielded
cable to the rear solder lugs of awall plate fitted with
two RCA jacks on its front. Terminate the shield at the
Right negative (-) or Left negative (-) ring of the solder
lugs. RCA cables can be used to connect the amp or sub-
woofer to the wall place for audio signal feed.
3 Speaker Output Connector for Speakers
The Speaker Output connections provide speaker-level
audio output for apair of 8-ohm speakers. The screw-
down terminals accepts up to 16 gauge speaker wire.
4 Status Jumper for Status LED Enable/Disable
The Status option provides visual indication when source
equipment is powered on. With this option enabled, the
status LED shows green on the keypad when the system
is on (keypad can be on or off).
To enable the Status LED, locate the status pins on the
right side of the keypad under the faceplate. Place the
status jumper over the bottom two pins to enable the
status LED.
Note: Amplified keypads are shipped with the Status LED
option disabled (default).
Status function and operation:
When the source is powered on, the Status circuit is
powered by 12VDC and turns the keypad's status LED to
green. This indicates to the user that the source is on and
ready to receive remote control commands.
When the source is powered off (remotely or manually),
it shuts off the 12VDC Status power connected to it, and
turns off all the interfaces connected to the controller
(green LED off).
5 Source ModeJumper for Single/Multisource
The single/multisource jumpers set the A-K3 to be used
with either single- or multi-source A-BUS hubs/control-
lers. The jumpers and pins are located underthe face-
plate on the right side of the keypad (facing front).
The pins are jumpered to select between 1,4 and 6
sources. 1source =no jumper; 4sources =top two pins
jumpered; 6sources = bottom two pins jumpered.
6 Gain Control for Maximum Levels
The two rotary trim potentiometers on the side of the
A-K3 provide adjustment of audio gain. These are used to
set the maximum allowable volume for the left and right
speakers connected to the A-K3.
7 Keypad Connection to A-C68 Controller
Each keypad connects to aKeypad Output port on the
back of the A-C68 controller. Connections are made using
CAT-5 cable with an RJ45 connector.
The Keypad Ports are located on the back of the A-C68
on the left. Connections at the Keypad Ports are made
with RJ45 connectors using T568A CAT-5 wire configura-
tion. CAT-5 cable length should be no longer than 150
feet from controller to keypad.
If used in asystem with A-K5L keypads, when connecting
A-K3 keypads to the A-C68, the keypad dip switches on
the controller's front programming center must be set in
the UP position. Dip switches correspond to numbered
keypad ports.
If used in a A-C68 system with no A-K5L keypads, set the
keypad dip switches in the UP position.
For aclean installation when wiring from aKeypad Port,
use an RJ45 CAT-5 patch cable to connect from the key-
pad port to an RJ-45 wall plate (optional). Using the same
RJ45 T568A CAT-5 wiring configuration, use CAT-5 from
the RJ45 wall plate to the keypad.
8Installation
Check all connections and test the system's operation
before installing the A-K3 into the wall. Using the includ-
ed hardware, install the A-K3 into astandard UL/CSA
single-gang electrical J-box.
Conforlllslo
UL 6500
Cet1ified 1o
CANlCSA
Copyright © 2007 Russound All rights reserved. All trade-
marks are property oftheir respective owners. Russound is not
responsible for typographical errors or omissions. Specifications
subject to change without notice.

Read Instructions -All the safety and operating instructions should
be read before the appliance is operated.
Retain Instructions -The safety and operating instructions should
be retained for future reference.
Heed Warnings -All
warnings on the appliance in the operating
instructions should be adhered to.
Follow Instructions - Follow all operating and user instructions.
Water
and Moisture -The appliance should not be used near water;
for example, near a bathtub, washbowl, kitchen sink, laundry tub, in
a wet basement, or near a swimming pool.
Wall or Ceiling Mounting -The appliance should be mounted to a
wall or ceiling only as recommended by the manufacturer.
Heat -The appliance should be situated away from heat sources
such
as radiators, heat registers, stoves, or other appliances (includ-
ing amplifiers) that produce heat.
Power Sources -The appliance should be connected to a power
supply only of the type described in the operating instructions or as
marked on the appliance.
Grounding or Polarization -Precaution should be taken so that the
grounding or polarization means of an appliance is not defeated.
Object and Liquid Entry -Care should be taken so that objects do
not fall and liquids are not spilled into the enclosure through the
openings.
Damage Requiring Service -The appliance should be serviced by
qualified service personnel when:
The
power supply cord or the plug has been damaged;
Objects have fallen, liquid has been spilled into the appliance;
The appliance has been exposed
to rain;
The appliance does
not appear to operate normally; or
The appliance has been dropped or the enclosure is damaged.
Servicing -The user
should not attempt to service the appliance
beyond that described in the operating instructions. All other ser-
vicing should be referred to qualified service personnel.
Care -From
time to time you should wipe off the front panel with a
soft
dry cloth.
10.
13.
12.
2.
11.
9.
8.
3.
7.
6.
4.
S.
Safety Instructions
1.
Limited Warranty
The Russound A-K3 is fully guaranteed for two (2) years from the date of purchase
against all defects in materials and workmanship. During this period Russound will
replace any defective parts and correct any defect in workmanship without charge
for either parts or labor. For this warranty to apply, the unit must be installed and used
according to its written instructions. If service is necessary, it must be performed by
Russound. Russound assumes no responsibility for defects resulting from abuse or
servicing performed by an agency or person not specifically authorized in writing by
Russound. Damage to or destruction of components due to improper use voids the
warranty.
In these cases the repair will be made at the owner's expense. Accidental
damage and shipping damage are not considered defects under the terms of the
warranty.
To return for repairs, the unit must be shipped to Russound at the owner's
expense, along with a Return Authorization number and documentation explaining
the nature
of the service required. Any product returned without prior written per-
mission will be returned to sender. Russound sells products only through authorized
Dealers and Distributors to ensure that customers obtain proper support and service.
Any Russound product purchased from an unauthorized dealer or other source,
including retailers, mail order sellers and online sellers will not be honored or serviced
under existing Russound warranty policy. Any sale of products by an unauthorized
source or other manner not authorized by Russound shall void the warranty on the
applicable product.
l. ~Russound.
5Forbes Rd., Newmarket, NH 03857, USA
Tel [phone] •
Fax [phone]
e-mail: [email protected]
28-1258 10/19/07