Safe Fleet PRIME DESIGN HRX-009-E-RETRO User manual

PRIME DESIGN, A SAFE FLEET BRAND ▪ Address: 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118
Toll Free: 1.8.PRIME.RACK ▪ Fax: [phone] ▪ Email: [email protected] ▪ Website: www.primedesign.net

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability
(the “Prime Design Limited Warranty”).
▪ TM & © 2020 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608 AND OTHER PATENTS PENDING
2
1
7
8
3
5
6
4
9
10
2
11
HRX-009-E-RETRO ASSEMBLY INSTRUCTIONS–PACKAGING CONTENTS
CONTENTS OVERVIEW
1—Rear Crossbar Assembly.................................. (Qty 1)
2—Front Crossbar Assembly ................................. (Qty 1)
3—Rear Drive Shaft .............................................. (Qty 1)
Left Hand, A Version, 50.00”
4—HHR Handle Assembly .................................... (Qty 1)
35.00”
5—Connecting Bar ................................................ (Qty 1)
4.00’
6—Front Drive Shaft ............................................. (Qty 1)
B Version, 35.75”

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability
(the “Prime Design Limited Warranty”).
▪ TM & © 2020 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608 AND OTHER PATENTS PENDING
3
HRX-009-E-RETRO ASSEMBLY INSTRUCTIONS–PACKAGING CONTENTS
9—Z Post ............................................................... (Qty 1)
Adjustment, 7.25”
10—L Post ................................................................ (Qty 1)
G1, Square Cap, 9.25” w/Hardware
7—Hydraulic Cylinder ............................................ (Qty 1)
8—BLT-6811-M8.................................................... (Qty 1)
Cylinder Hex Head Assembly, M8 x 110MM
12—HKT-8163 (Not called out in Overview)........ (Qty 1)
11—USQSG-Ergorack ............................................ (Qty 1)
Quick Start Guide, Rotation
" Flat Washer (10X)
Anti-Seize (1X)
Lubricant (1X)
Clevis Pin (1X)
Cotter Pin (1X)
M8 x 50MM (4X) ⅜" x 2.25" (2X)
1.00" Sealing
Stickers (16X)
M8 Lock Nut (5X) ⅜" Lock Nut (2X) ⅜" Flat Washer (4X)
M8 x 25MM (1X)
M8 Lock Nut (1X) " Flat Washer (1X)
M8 x 65MM (1X)

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability
(the “Prime Design Limited Warranty”).
▪ TM & © 2020 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608 AND OTHER PATENTS PENDING
4
HRX-009-E-RETRO ASSEMBLY INSTRUCTIONS–LEFT SIDE ROTATION
1
2/5/12
4
6
7
9
3
8
10
3
11
Bushing,
1.75”L
Bushing,
1.25”L
Nylon
Washer
Flanges face
each other
Flange
1.1
Torque to 55 in-lbs
1.2
REAR CROSSBAR ROTATION
NOTE: Ladder Rack is shown for illustrative
purposes only, and is not included with this
Slide Rotation Retrot Kit.
This Slide Rotation Retrot Kit contains only
the parts needed to repair, replace, or retrot
one Slide Rotation.
LEFT SIDE ASSEMBLY SEQUENCE

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability
(the “Prime Design Limited Warranty”).
▪ TM & © 2020 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608 AND OTHER PATENTS PENDING
5
HRX-009-E-RETRO ASSEMBLY INSTRUCTIONS–LEFT SIDE ROTATION
2.1
Torque to 18 in-lbs
2.2
CYLINDER HARDWARE
NOTE: Flow Control Screw
faces toward vehicle rear
NOTE: Ensure Cylinder
Bushing is fully seated
against Crossbar
FRONT CROSSBAR ROTATION
3.1 Torque to 55 in-lbs
3.3
3.2 Press the small .75” (A) round Caps
into the Crossbar holes as shown.

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability
(the “Prime Design Limited Warranty”).
▪ TM & © 2020 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608 AND OTHER PATENTS PENDING
6
HRX-009-E-RETRO ASSEMBLY INSTRUCTIONS–LEFT SIDE ROTATION
REAR DRIVE SHAFT
4.1
4.2
4.3
Torque to
90 in-lbs
4.4
CYLINDER HARDWARE
5.1
5.2
CONNECTING BAR
6.1
6.2

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability
(the “Prime Design Limited Warranty”).
▪ TM & © 2020 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608 AND OTHER PATENTS PENDING
7
HRX-009-E-RETRO ASSEMBLY INSTRUCTIONS–LEFT SIDE ROTATION
FRONT DRIVE SHAFT
Torque to
90 in-lbs
7.1
7.2
7.3
7.4
CONNECTING BAR FASTENERS
8
Z POST
SEE QUICK START GUIDE FOR ADJUSTMENTS
Torque to 90 in-lbs
9.1
9.2
L POST
10
Torque to 90 in-lbs

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability
(the “Prime Design Limited Warranty”).
▪ TM & © 2020 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608 AND OTHER PATENTS PENDING
8
HRX-009-E-RETRO ASSEMBLY INSTRUCTIONS–LEFT SIDE ROTATION
USAM-HRX009ERETRO-US01 Rev-B 0218
DRIVE SHAFT SEALING
Apply Silicone Sealant
to Connecting Bar ends
11.2
11.1
Adjust the Cylinder Flow
Control Screw to allow
approximately 3 seconds
time for the ladder to glide
down when operating the
loaded Ladder Rack.
12
CYLINDER ADJUSTMENT