Safe Fleet PRIME DESIGN OCM-3032 User manual

OCM-3032
OVER THE CAB ADD-ON CROSSBAR
PRIME DESIGN, A SAFE FLEET BRAND ▪ Address: 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118
Toll Free: 1.8.PRIME.RACK ▪ Fax: [phone] ▪ Email: [email protected]t ▪ Website: www.primedesign.net

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability
(the “Prime Design Limited Warranty”).
▪
TM & © 2020 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608 AND OTHER PATENTS PENDING
2
OCM-3032 ASSEMBLY INSTRUCTIONS–PACKAGING CONTENTS
Pickup Crossbar .................................................... (Qty 1)
67.00”, with Caps and Hardware
CONTENTS OVERVIEW
Lock Washer (4X) Mounting Connector (4X)
Anti-Seize
M8 x 50MM (4X) M8 x 60MM Carriage Bolt (2X)
End Stop (2X)LH Removable
Crossbar Mount (1X)
RH Removable
Crossbar Mount (1X)
M8 Lock Nut (2X) " Flat Washer (6X)
M8 Nut Bracket (4X)
HKT-0183 Removable Crossbar Hardware Kit

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability
(the “Prime Design Limited Warranty”).
▪
TM & © 2020 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608 AND OTHER PATENTS PENDING
3
Left side shown-repeat on right
OCM-3032 ASSEMBLY INSTRUCTIONS–ASSEMBLY INSTRUCTIONS
M8 x 60MM Carriage Bolt
Locknut
Flat Washer
M8 x 50MM
Lock Washer
Flat Washer
Leave M8 Nut Brackets
loose until Step 5
Leave M8 Nut Brackets
loose until Step 5
Slide rear Removable
Crossbar forward
ASSEMBLY INSTRUCTIONS
NOTE: Channels in this Overview are shown for
reference only. Specic channels and congurations
are determined by Service Body size.
CROSSBAR MOUNT BUILDS PRE-INSTALLED
REMOVABLE CROSSBAR
1.1
1.2
2.1
Loosen bolts
2.2

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability
(the “Prime Design Limited Warranty”).
▪
TM & © 2020 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608 AND OTHER PATENTS PENDING
4
USAM-OCM3032-US01 Rev-A 0220
Variable Placement
Flush to end
OCM-3032 ASSEMBLY INSTRUCTIONS–ASSEMBLY INSTRUCTIONS
ADD-ON CROSSBAR INSTALLATION
3Install Mounts into Channels
as shown below.
4.1
Set Crossbars into the Mounts
as shown and torque Crossbar
Connector Hardware to 90 in-lbs.
Attach Ladder stops as shown
and torque to 90 in-lbs.
4.2
5Set to distances as shown below, and torque all Removable Crossbar Mounts into the Channels at 90 in-lbs.
NOTE: Channels and FBM are shown for reference. Specic channels and congurations are determined by
Service Body size.