Samsung SHP-DS700 User manual

SHP-DS700
Samsung SDS Door Lock
User and Reference Guide
Ver1.0.0

2 / 12
Product Specifications
Item
Spec.
Size
Exterior Unit
41mm (W) X 41mm(H) X 9.5mm(D)
Interior Unit
70mm (W) X 53mm(H) X 22mm(D)
Voltage
AA Alkaline 1.5V Batteries (LR6) 4EA (6V)
Emergency Power Source
9V Battery(6LF22) (Separately sold)
Battery Life
10 Months (based on an average of 10 uses per day with a
wireless module not mounted)
Support Card Standard
ISO14443A (Mifare®)
Exterior Parts
Interior Parts

3 / 12
The Samsung SDS Z-Wave Door Lock is a security enabled Z-Wave Plus product that is able to use
encrypted Z-Wave Plus messages to communicate to other security enable Z-Wave Plus products.
The Samsung SDS Z-Wave Door Lock must be used in conjunction with a Security Enabled Z-Wave
Controller in other to fully utilize all implemented functions.
The Samsung SDS Z-Wave Door Lock can be included and operated in any Z-Wave network with
other Z-Wave certified devices from other manufacturers and/or other applications. All non-battery
operated nodes within the network will act as repeaters regardless of vendor to increase reliability of
the network.
Z-Wave Specifications
Device Type : Door Lock –Keypad (SPECIFIC_TYPE_SECURE_KEYPAD_DOOR_LOCK)
Role Type : LSS (Listening Sleeping Slave)
Command Class Support/Control
Mandatory CC support :
Z-Wave plus info (MUST be place first in NIF) –(V2)
Manufacturer Specific (V2)
Security (V1)
Device Reset Locally (V1)
Battery (V1)
Power Level (V1)
Version (V2)
Door Lock (V2)
User Code (V1)
Association (V2)
Association Group Information (V1)
Recommended CC support
Notification (V4)
Configuration (V1)
Firmware update meta data (V2)
Schedule Entry Lock (V3)
Time Parameters (V1)
Time (V2)

4 / 12
Z-Wave plus info (V2)
- Z-Wave Plus Version : 02
- Role Type : LSS (Listening Sleeping Slave)
- Node Type : Z-Wave Plus Node
Manufacturer Specific (V2)
-Device ID Type : 01(Serial Number)
- Device ID Data Format : 01 (Binary)
- Device ID Data Length Indicator : 16
-Device ID : XX XX XX XX XX XX XX XX XX XX XX XX XX XX XX XX
Version (V2)
- Z-Wave Protocol Library Type : 03
- Z-Wave Protocol Version : 04
- Z-Wave Protocol Sub Version : 05
- Firmware 0 Version : 01
- Firmware 0 Sub Version : 03
- Hardware Version : 01
Door Lock (V2)
- support Unsecure(0x00), Secure(0xFF)
Note : When using ‘Operation_Set’command, lock will execute ‘Unsecure(0x00)’then
perform ‘Auto Re-lock’if door is not open.
When using ‘Operation_Get’command, lock can response after executing
‘Operation_Set’command. (take about 2 seconds)
User Code (V1)
- Lock will accept maximum 30 pin codes that are 4-10 digits in length.
①Supported Users : 30
②User Type : Number, Card (Key Tag)
⋅Card (Key Tag) : Cannot be registered through Z-Wave
③ID Range
⋅Number : 1 ~ 30

5 / 12
⋅Card (Key Tag) : 1 ~ 20
⋅Bluetooth : 21 ~ 30
Association (V2) & Association Group Information (V1)
- Lifeline between controller and SHP-DS700
- Supported command classes
: Battery report, Notification report, and Device Reset Locally notification
- Maximum supported node is 1EA
Notification (V4)
Notification Type
Event
Event Parameter
Access Control
(0x06)
Manual Lock Operation (0x01)
Manual Unlock Operation (0x02)
RF Lock Operation (0x03)
RF Unlock Operation (0x04)
Keypad Unlock Operation (0x06)
User ID
RF Not Fully Locked Operation (0x08)
Auto Lock Loced Operation (0x09)
Auto Lock Not Fully Operation (0x0A)
Lock Jammed (0x0B)
All user codes deleted (0x0C)
Single user code deleted (0x0D)
New user code added (0x0E)
New user code not added due to
duplicate code (0x0F)
New Program code Entered - Unique
code for lock configuration (0x12)
Home Security
(0x07)
Intrusion, Unkown Location (0x02)
Tampering, Invalid Code (0x04)

6 / 12
Motion Detection, Unknown Location
(0x08)
Emergency
(0x0A)
Contact Police (0x01)
Contact Fire Service (0x02)
Configuration (V1)
Name
Parameter
Number
Size
Value
Description
Security Function
0x01
1byte
0x00
0x01
0x02
0x03
0x04
0x05
Disable (Default)
Enable
System Disable1)
System Enable1)
Request for Enable1)
Fail1)
Privacy Mode
0x02
1byte
0x00
0x01
Disable (Default)
Enable
Registered User
ID
0x03
1byte
1 ~130
The number of registered user codes.2)
Platform
0x0A
1byte
0x00
0x01
Common (Default)
Samsung SDS3)
1) This value can be used when the device is connected with platform of Samsung SDS.
This function is not related to Z-Wave CC.
- 0x02 : Command for disable which is set by platform of Samsung SDS.
After setting, if you try to get value of Security Function , '0x00' will be reported.
- 0x03 : Command for enable which is set by platform of Samsung SDS.
After setting, if you try to get value of Security Function, '0x01' will be reported.
- 0x04 : 'Request for Enable' command which is reported by Doorlock. This cannot be set.
(8th function in manual)
- 0x05 : If the request for 'Request for Enable' command is failed in platform,
this will be set by platform of Samsung SDS.

7 / 12
Value of Security Function is not changed by this command.
2) This parameter is supported to ‘Configuration Get Command’only.
3) This value set by platform after device connected with platform of Samsung SDS.
Firmware update meta data (V2)
-Manufacturer ID : 0x022E (Samsung SDS)
Schedule Entry Lock (V3)
- Supported the Number of Slots Week Day : 0
- Supported the Number of Slots Year Day : 0
- Supported the Number of Slots Daily Repeating : 30
Glossary
Device or Node
Devices and nodes are all terms to describe an individual Z-Wave device. These
are all interchangeable when setting up your Z-Wave network
Unsecure /
Unsecured
Unlock / Unlocked
Secure / Secured
Lock / Locked
Inclusion
Add a Z-Wave device to the network
Exclusion
Delete a Z-Wave device from the network
Z-Wave Network
A collection of Z-Wave devices is controlled by primary and secondary controllers
operating on the same system. A Z-Wave network has its own unique ID code so
that controllers not in the network cannot control the system.
Association
Association is used to organize nodes in different groups allowing the device to
identify the nodes by a group identifier. The groups can also be copied to other
devices.

8 / 12
Note : Pressing the [REG] button is only available while the door is open. (Deadbolt must be
unsecured.)
Basic Functions
1. Factory Reset
All registered Master/User data will be deleted, and Master PIN Code is set to ‘1234’. Also Z-
Wave Door Lock is being removed from a network.
① Press the [REG] button for 3 seconds. (Ding dong -> Ding ding)
② Press the [*] button after pressing the [4567890123] button.
(Success : Ding dong dang, Fail : Ding dong Ding dong)
※Use this procedure only in the event that the network primary controller is missing or
otherwise inoperable.
2. Changing the Master PIN Code
You can enter only one Master PIN Code. If changing the Master PIN code, All User PIN
Codes are deleted.
① Press the [REG] button. (Ding dong)
② Enter the new Master PIN Code, and press the [*] button.(4~12digits) (Ding dong dang)
3. Registering a User Card
You can register up to 20 User Card. (Supproted ISO14443 A Type)
To register multiple cards, lightly place another card to the card reader within 20 seconds
after registering the previous card. Also you can add card later after completing registration.
① Press the [REG] button. (Ding dong)
② Place the card to be registered on the card reader of the exterior body.(Ding dong dang)
③ Place the card on the card reader for the addtional registration or press the [REG] button
to quit.

9 / 12
4. Registering a Bluetooth
① Press the [REG] button. (Ding dong)
② Enter the [88] + [*] (Ding dong)
③ Enter the Password + [*] (Ding dong deng →Ding ding)
④ Check a pairing number from Smart Door Lock App of smartphone.
(First, please install the Smart Door Lock app in the smart phone.)
⑤ Enter a Pairing number + [*] (Ding dong deng)
5. Inclusion / Exclusion into(from) Z-Wave Network
5.1 Inclusion into Z-Wave Network
① Click [Add] icon in Z-Wave PC Conroller Program.
② Press the [REG] button for 3 seconds. (Ding dong -> Ding ding)
③ Press the [*] button after pressing the [00] button.
(Success : Ding dong dang, Fail : Ding dong Ding dong)
5.2 Exclusion from Z-Wave Network
After exclusion from Z-Wave Netwokr, it will no longer be remotely-controlled via the
controller.
① Click [Remove] icon in Z-Wave PC Conroller Program.
② Press the [REG] button for 3 seconds. (Ding dong -> Ding ding)
③ Press the [*] button after pressing the [00] button.
(Success : Ding dong dang, Fail : Ding dong Ding dong)
6. Opening the Door with a PIN Code
① Touch the [Number Pad].
② Enter the PIN Code and press the [*] button.
③ The door opens whithin one second.

10 / 12
7. Opening the Door with a Card
① Place the Card on the Card Reader.
② The door opens whithin one second.
8. Opening the Door with a Bluetooth
① Access the door lock from the outside or touch its number pad.
② The number pad will light up.
③ Push message is sent to smartphone through Bluetooth.
④Press the icon of push message (from smartphone)
⑤ Then push the door handle to open the door.