Sauder Whitaker Point 429372 User manual

sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE RETAILER.
Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep.
Prefer the phone? Give us a ring at 1-800-445-1527.
Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays)
Sauder.com
Share your journey!
Enlish p 1-32
Français p 33-36
Español p 37-40
Lot # 573730 11/16/21
Purchased: __________________
Library Hutch
Whitaker Point Collection | Model 429372
Don't sweat the
small stu anymore.

Part Identification
Hardware Identification
Hardware Usage Guide
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Table of Contents Assembly Tools Required
3
4
5
6-32
33-36
37-40
41-42
43
Electric drill with 1/8" or 3/8" bit
(ONLY in indicated step)
Pencil
Pae 2 www.sauder.com/service 429372

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A LEFT END (1)
B RIGHT END (1)
C TOP (1)
D BOTTOM (1)
E SHELF (1)
F LEFT BACK (1)
G RIGHT BACK (1)
H MOLDING (1)
J DRAWER FRONT (1)
K LEFT DRAWER SIDE (1)
L RIGHT DRAWER SIDE (1)
M DRAWER BACK (1)
N DRAWER BOTTOM (1)
O DRAWER BRACE (1)
A
B
C
D
E
F
G
H
J
K
L
MN
O
Pae 3www.sauder.com/service429372

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
(EXTENSION SET SHOWN SEPARATED)
1EXTENSION RAIL - 2 2EXTENSION SLIDE - 2 LARGE WOOD
DOWEL - 20
3SMALL WOOD
DOWEL - 6
4
LARGE HIDDEN
CAM - 16
5SMALL HIDDEN
CAM - 3
6 7 CAM SCREW - 19 SHELF PIN - 4 8
BACK PLATE - 2
9METAL BRACKET - 5
10 PULL - 1
11 APPLIQUE CARD - 1 12
1-1/2" FLAT HEAD SCREW - 3
16 3/8" FLAT HEAD SCREW - 12
17
2" FLAT HEAD SCREW - 4
13 5/8" PAN HEAD SCREW - 12 14 15 12" MACHINE SCREW  2
1/2" PAN HEAD SCREW - 10
18
Pae 4 www.sauder.com/service 429372
FURNITURE TIPPING
RESTRAINT KIT - 1
96
LONG WOOD
DOWEL - 3
19

Hardware Usage Guide
HOW TO USE A HIDDEN CAM & CAM SCREW OR CAM DOWEL
NOTE: Various CAM SCREWS or a CAM DOWEL may be used.
Cam Screws Cam Dowel
Turn the CAM SCREW or
gently tap the CAM DOWEL
until the shoulder is against
the surface of the part.
1.
Hidden Cam
Arrow
Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the
edge of the board.
Hole
2.
3.
1
2
Insert the CAM SCREW or CAM DOWEL into the
HIDDEN CAM. Tighten the HIDDEN CAM.
Pae 5www.sauder.com/service429372

Step 1 Look for this icon. It means a video assembly tip is
available at www.sauder.com/service/tips
Find the numbered video or scan the QR code.
å Assemble your unit on a carpeted floor or on the empty carton
to avoid scratchin your unit or the floor.
å Push eiht LARGE HIDDEN CAMS (5) into the BACKS (F and G).
1
Pae 6 www.sauder.com/service 429372
F
G
5
Arrow
5
Arrow
Arrow
5
Just think. The sooner
you do this, the sooner
you do somethin else.

Step 2
å Insert three LONG WOOD DOWELS (19) into the RIGHT BACK (G).
å Push the LEFT BACK (F) onto the LONG WOOD DOWELS (19) in
the RIGHT BACK (G).
Pae 7www.sauder.com/service429372
Surface with HIDDEN CAMS
Surface with HIDDEN CAMS
19
F
G

å Push four LARGE HIDDEN CAMS (5) into the BOTTOM (D).
Step 3 1
D
Arrow
5
5
Arrow
Pae 8 www.sauder.com/service 429372

Step 4
å IMPORTANT: You will need two people in this step.
å Insert two LARGE WOOD DOWELS (3) into the BACKS (F and G).
å Fasten the BOTTOM (D) to the BACKS (F and G). Use four 2" FLAT
HEAD SCREWS (13).
å NOTE: Be sure the WOOD DOWELS in the BACKS insert into
the BOTTOM.
Pae 9www.sauder.com/service429372
D
F
G
3
3
2" FLAT HEAD SCREW
(4 used in this step)
13
Surface with
HIDDEN CAMS
Do not stand the unit upriht without the
BACK fastened. The unit may collapse.
Caution

å Push two LARGE HIDDEN CAMS (5) into the LEFT END (A).
å Turn five CAM SCREWS (7) into the LEFT END (A).
Step 5 1
Pae 10 www.sauder.com/service 429372
A
5
Arrow
7
7

å Separate the EXTENSION SLIDES (2) from the EXTENSION RAILS (1) as shown in the upper diaram below. Be
prepared, the parts are reasy.
å Fasten a EXTENSION RAIL (1) to the LEFT END (A). Use three 3/8" FLAT HEAD SCREWS (17).
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlared diaram. Then, slide the inner
cartride of the EXTENSION RAIL in to find the other holes that lines up with the holes in the LEFT END. Turn a
SCREW into these holes.
å NOTE: The EXTENSION SLIDES will be used later for the DRAWERS.
Step 6
A
1
Open end
Push the black lever and pull the SLIDE from the RAIL.
21
Pae 11www.sauder.com/service429372
3/8" FLAT HEAD SCREW
(3 used in this step)
17
7

StepStep 7
å Insert four LARGE WOOD DOWELS (3) into the LEFT END (A).
å Fasten the LEFT END (A) to the BOTTOM (D) and LEFT BACK (F).
Tihten five HIDDEN CAMS.
å NOTE: Be sure the LARGE WOOD DOWELS in the LEFT END
insert into the BOTTOM and LEFT BACK.
A
D
F3
3
1
Pae 12 www.sauder.com/service 429372

Step
å Push two LARGE HIDDEN CAMS (5) into the RIGHT END (B).
å Turn five CAM SCREWS (7) into the RIGHT END (B).
Step 8 1
B
5
Arrow
7
7
Pae 13www.sauder.com/service429372

Step 9
å Fasten a EXTENSION RAIL (1) to the RIGHT END (B). Use three 3/8" FLAT
HEAD SCREWS (17).
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the
enlared diaram. Then, slide the inner cartride of the EXTENSION RAIL in
to find the other holes that lines up with the holes in the RIGHT END. Turn a
SCREW into these holes.
B
Open end
1
3/8" FLAT HEAD SCREW
(3 used in this step)
17
Pae 14 www.sauder.com/service 429372
7

Step 10
å Turn your unit onto the LEFT END (A) as shown.
å Insert four LARGE WOOD DOWELS (3) into the RIGHT END (B).
å Fasten the RIGHT END (B) to the BOTTOM (D) and RIGHT BACK (G).
Tihten five HIDDEN CAMS.
å NOTE: Be sure the LARGE WOOD DOWELS in the RIGHT END insert
into the BOTTOM and RIGHT BACK.
1
Pae 15www.sauder.com/service429372
B
D
G
3
3
A

å Turn six CAM SCREWS (7) into the TOP (C).
Step 11 1
7
7
7
C
Pae 16 www.sauder.com/service 429372

å Insert two LARGE WOOD DOWELS (3) into the TOP (C).
å Push the MOLDING (H) onto the LARGE WOOD
DOWELS (3) in the TOP (C).
Step 12
Pae 17www.sauder.com/service429372
Surface with holes
C
H
3
3

å Fasten three METAL BRACKETS (10) to the TOP (C) and
MOLDING (H). Use six 1/2" PAN HEAD SCREWS (18).
å NOTE: You should start each SCREW a few turns before
completely tihtenin any of them.
Step 13
10
C
H
1/2" PAN HEAD SCREW
(6 used in this step)
18
Pae 18 www.sauder.com/service 429372
Now miht be a
ood time to refresh
your drink.

Step 14
å Turn your unit onto its back edes.
å Insert eiht LARGE WOOD DOWELS (3) into the TOP (C).
å Fasten the TOP (C) to the ENDS (A and B) and BACKS (F and G). Tihten four HIDDEN CAMS.
å NOTE: Be sure the LARGE WOOD DOWELS in the TOP insert into the ENDS and BACKS.
å NOTE: You will tihten the HIDDEN CAMS for the BACKS in the next step.
C
A
B
3
3
(8 used)
F
G
1
Pae 19www.sauder.com/service429372

å Carefully stand your unit upriht.
å Fasten the BACKS (F and G) to the TOP (C).
Tihten two HIDDEN CAMS.
å Open the FURNITURE TIPPING RESTRAINT KIT (96), and fasten the
SAFETY STRAP to the TOP (C). Use the provided SHORT SCREW.
Step 15 1
Pae 20 www.sauder.com/service 429372
96
Use the SHORT SCREW
from the RESTRAINT KIT.
SAFETY STRAP
C
F
G
Pro Tip: Lift with your
les. And, you know,
your arms.