Sauder 413081 User manual

Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-16
Français pg 17-18
Español pg 19-20
Lot # 386563 12/01/15
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987
4 Drawer Chest
Beginnings Collection | Model 413081
The dresser's
not-so-distant cousin.

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
No. 2 Phillips Screwdriver
Tip Shown Actual Size
3
4
5-16
17-18
19-20
21-22
23
Hammer
Not actual size
Skip the power trip.
This time.
Scissors
Tape Measure
413081 www.sauder.com/servicesPage 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A2 RIGHT END (1)
B2 LEFT END (1)
C TOP (1)
D BRACE (3)
E BACK (2)
G SKIRT (1)
H LARGE DRAWER FRONT (3)
L DRAWER FRONT (1)
D486 LARGE DRAWER SIDE (6)
D487 LARGE DRAWER BACK (3)
D488 DRAWER SIDE (2)
D489 DRAWER BACK (1)
D610 DRAWER BOTTOM (4)
A2
B2
C
D
E
G
H
L
D
E
DD610
D610
D486
D486
D487
D488
D488
D489
413081www.sauder.com/services Page 3

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
APPLIQUE CARD - 2
29P
5L WARNING LABEL - 1
(Refer to the last step for proper
location and application)
WARNING
Serious or fatal crushing injuries can occur
from furniture tip-over. To help prevent
tip-over:
• Place heaviest items in the lowest drawers.
• Unless specifically designed to accommodate, do not
set TVs or other heavy objects on top of this product.
• Never allow children to climb or hang on drawers,
doors, or shelves.
• Never open more than one drawer at a time.
• If equipped with a drawer interlock system, do not
defeat or remove it.
Use of tip-over restraints may only reduce, but not
eliminate, the risk of tip-over.
This is a permanent label. Do not attempt to remove!
04/10 332296
SLIDE SET - 4
16B
DRAWER FRONT
BRACKET - 14
30G
SAFETY BRACKET - 1
1G
BLACK 9/16" LARGE HEAD SCREW - 23
1S
ANGLE BRACKET - 8
5G
BROWN 7/16" LARGE HEAD SCREW - 8
6S
BLACK 1-7/8" FLAT HEAD SCREW - 17
2S
METAL PIN - 4
1R
BLACK 1/2" FLAT HEAD SCREW -28
43S BLACK 1-1/2" PAN HEAD SCREW - 16 49S
HIDDEN CAM - 4
1F CAM DOWEL - 4 2F
PULL - 4
45K
SILVER 3/4" MACHINE SCREW - 8
53S52S SILVER 3/4" PAN HEAD SCREW - 16
413081 www.sauder.com/servicesPage 4

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Push four HIDDEN CAMS (1F) into the ENDS (A2 and B2).
Then, insert the metal end of a CAM DOWEL (2F) into
each HIDDEN CAM.
413081www.sauder.com/services Page 5
Scan this QR code or go to this address:
http://qr.sauder.com/?ID=1328
to watch a video on how to assemble your unit.
A2
B2
Arrow
1F
2F
(4 used)
Do not tighten the HIDDEN CAMS in this step.
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow

å NOTE: Before beginning this step, separate the SLIDES from the SLIDE SETS (16B) and the DRAWER PINS at the end of
the SLIDES using a SCISSORS. Save the DRAWER PINS. You will use them in Step 11.
å Fasten the SLIDES (16B) to the ENDS (A2 and B2). Use sixteen SILVER 3/4" PAN HEAD SCREWS (52S) through the first
and last holes in the SLIDES.
å NOTE: The SLIDES are marked "RIGHT" and "LEFT" for easy identification. The SLIDES marked "RIGHT" will fasten to the
RIGHT END (A2) and the SLIDES marked "LEFT" will fasten to the LEFT END (B2). There are also arrows on the SLIDES
for correct positioning on the ENDS.
Step 2
413081 www.sauder.com/servicesPage 6
16B
A2
B2
16B
16B
16B
16B
16B
16B
16B
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
Finished edge
SILVER 3/4" PAN HEAD SCREW
(16 used in this step)
52S
Notch
Straight edge
Angled edge
16B
DRAWER PIN
(Save for Step 11)
Using your Scissors, separate the
SLIDES and the DRAWER PINS.
RIGHT SLIDES
LEFT SLIDES
Finished edge

å Fasten four ANGLE BRACKETS (5G) to the BACKS (E).
Use four BROWN 7/16” LARGE HEAD SCREWS (6S).
å Fasten two ANGLE BRACKETS (5G) to the SKIRT (G). Use
two BLACK 9/16” LARGE HEAD SCREWS (1S).
å NOTE: Be sure the edges of the ANGLE BRACKETS are
even with the edges of the BACKS and SKIRT.
Step 3
413081www.sauder.com/services Page 7
E
E
G
Surface
with holes
5G
5G
BLACK 9/16" LARGE HEAD SCREW
(2 used for the SKIRT)
1S
BROWN 7/16" LARGE HEAD SCREW
(4 used for the BACKS)
6S
Surface
with holes
Remember:
Righty tighty.
Lefty loosey.

å Fasten the ENDS (A2 and B2) to the TOP (C). Tighten
four HIDDEN CAMS.
Step 4
413081 www.sauder.com/servicesPage 8
A2
B2
C
Surface with holes
Start Tihten
Arrow
Minimum
190 degrees
Caution
Risk of damage or
injury. HIDDEN CAMS
must be completely
tightened. HIDDEN
CAMS that are not
completely tightened
may loosen, and parts
may separate. To
completely tighten:
Arrow
Maximum
210 degrees
Finished edge
Long finished edge

å Insert four METAL PINS (1R) into the BACKS (E).
å Insert the METAL PINS (1R) in the BACKS (E) into the
holes in the TOP (C).
å Fasten the BACKS (E) to the ENDS (A2 and B2). Use four
BROWN 7/16" LARGE HEAD SCREWS (6S) through the
ANGLE BRACKETS on the BACKS and into the ENDS.
Step 5
413081www.sauder.com/services Page 9
A2
B2
C
EE
1R
Edge and surface with
ANGLE BRACKETS.
Edge and surface with
ANGLE BRACKETS.
(4 used)
BROWN 7/16" LARGE HEAD SCREW
(4 used in this step)
6S

å Fasten the BRACES (D) to the ENDS (A2 and B2). Use
twelve BLACK 1-7/8" FLAT HEAD SCREWS (2S).
å Fasten the lower BRACE (D) to the BACKS (E). Use four
BLACK 1-7/8" FLAT HEAD SCREWS (2S).
Step 6
413081 www.sauder.com/servicesPage 10
A2
B2
E
E
D
D
Surface with more holes
D
2S
These holes
must be here.
These holes
must be here.
Surface with more holes
Surface with more holes
BLACK 1-7/8" FLAT HEAD SCREW
(16 used in this step)
2S
Now might be a
good time to refresh
your drink.