Sauder Rose Valley 404867 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-31
Français pg 32-35
Español pg 36-40
Lot # 370261 03/04/15
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987
Entertainment Credenza
Rose Valley Collection | 404867
Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
Your center of
attention.

Table of Contents Assembly Tools Required
3
4-5
6-31
32-35
36-40
41-42
43
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Use of a TV that is too heavy or large is hazardous. A TV that is too heavy will create a risk of a tip-over that can cause severe injury or
death. A TV that is too large for the available space might be accidentally pushed or bumped o the furniture, or subject to tip-over.
• Check the size and weight of your TV. Compare it to the diagram below – before you begin assembly!
• This Sauder unit is designed for use with televisions weighing less than 135 pounds. Never use with a TV that weighs more.
• The size of the television, front-to-back and side-to-side, must fit within the space defined in the diagram.
• Never place the front edge of the TV past the front edge of the TV support shelf (or stop molding – if equipped)
• Never allow the sides of the TV to extend past the side edges of the TV support surface.
• If the TV has a CRT picture tube, the picture tube cone may extend past the rear of the support shelf.
• Be sure to apply the warning label as instructed in the last assembly step. The label provides important safety related information.
WARNING
!
135 lbs.
135 lbs.
19-1/4"
19-1/4"
63-3/8"
63-3/8"
Skip the power trip.
This time.
404867 www.sauder.com/servicesPage 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C RIGHT UPRIGHT (1)
D LEFT UPRIGHT (1)
E TOP (1)
F BOTTOM (1)
G SHELF (1)
H BACK (2)
I CENTER BACK (1)
J DOOR (2)
K ADJUSTABLE SHELF (4)
L2 RIGHT LEG (1)
M2 LEFT LEG (1)
N REAR LEG (2)
O VALANCE (1)
P EXTENSION BLOCK (1)
Q DRAWER FRONT (1)
V BOTTOM MOLDING (1)
W END MOLDING (6)
X RIGHT SKIRT (1)
Y LEFT SKIRT (1)
D65 DRAWER BACK (1)
D107 RIGHT DRAWER SIDE (1)
D108 LEFT DRAWER SIDE (1)
D962 DRAWER BOTTOM (1)
Now you know
our ABCs.
404867www.sauder.com/services Page 3
A
B
C
D
E
F
G
H
I
J
K
L2
M2
NO
P
Q
V
X
Y
D108
D107
D65
D962
J
N
K
K
K
H
W
W

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
404867 www.sauder.com/servicesPage 4
ZRIGHT CABINET RAIL - 1 AA LEFT CABINET RAIL - 1 CC LEFT DRAWER SLIDE - 1
BB RIGHT DRAWER SLIDE - 1
HIDDEN CAM - 10
1F CAM DOWEL - 4 2F CAM SCREW - 6 8F
ADJUSTABLE FOOT - 1
DD2 FOOT BASE - 1 FFF EE TWIST-LOCK®FASTENER - 12
ANGLE BRACKET - 7
HH JJ HINGE - 4 FELT DISC CARD - 1 LL
PULL - 3
MM NN SLIDE CAM - 2 CAM COVER - 4 OO
METAL PIN - 16
PP RUBBER SLEEVE - 16 QQ RR WARNING LABEL - 1
WARNING
Never use this furniture with a TV that is too
large or too heavy. Severe injury or death
can occur.The TV and furniture will be
unstable and may tip.
-The TV must less than 135 lbs.
-The base of the TV must be able to sit
completely on this shelf.
-Refer to instruction book for complete safety
information.
Note: This is a permanent label. Do not try
to remove. Surface will be damaged.
02/ 02 2 6 9 2 3 2 269232
(Refer to Step 25 for proper
location and application)

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
404867www.sauder.com/services Page 5
BLACK 2-1/4" FLAT HEAD SCREW - 6
SS BLACK 1-7/8" FLAT HEAD SCREW - 12 TT
BLACK 1-1/8" PAN HEAD SCREW - 4
UU SILVER 3/4" MACHINE SCREW - 2
VV
BLACK 9/16" LARGE HEAD SCREW - 14
XX
BLACK 9/16" FLAT HEAD SCREW - 12
YY BLACK 1/2" FLAT HEAD SCREW - 8
AAA
BROWN 7/16" LARGE HEAD SCREW - 4
BBB CCC GOLD 5/16" FLAT HEAD SCREW - 8
NAIL - 12
DDD SILVER 5/8" FLAT HEAD SCREW - 4 GGG
30S BLACK 1-9/16" FLAT HEAD SCREW - 4
WW SILVER 5/8" MACHINE SCREW - 1

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å To begin assembly, push a SAUDER TWIST-LOCK®
FASTENER (EE) into the large holes in the ENDS (A and B).
å Repeat this step for the UPRIGHTS (C and D)
and BOTTOM (F).
404867 www.sauder.com/servicesPage 6
(12 used)
EE
Do not tighten the TWIST-LOCK® FASTENERS in this step.
A
B
STOP
If you purchased
the 407443
Entertainment
Hutch, assemble
that unit first.

å Push ten HIDDEN CAMS (1F) into the ENDS (A and B)
and BACKS (H). Then, insert the metal end of a CAM
DOWEL (2F) into each HIDDEN CAM in the BACKS (H).
Step 2
404867www.sauder.com/services Page 7
Arrow
1F
2F
Do not tighten the HIDDEN CAMS in this step.
Do not insert
CAM DOWELS
into these edges.
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
(10 used)
(4 used)
Arrow
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
Hole
1F
Arrow
A
B
H
H

Step 3
å Slide the BOTTOM MOLDING (V) onto the notched edge
of the BOTTOM (F).
å * U.S. Patent No. 5,499,886
404867 www.sauder.com/servicesPage 8
Slide the BOTTOM MOLDING (V) onto the notched edge.
Notched edge
V
F
Surface without
TWIST-LOCK®
FASTENERS

å Fasten the CABINET RAILS (Z and AA) to the UPRIGHTS (C
and D). Use four GOLD 5/16" FLAT HEAD SCREWS (CCC)
through holes #1 and #3.
å NOTE: The CABINET RAILS are marked "CABINET RIGHT"
and "CABINET LEFT" for easy identification.
Step 4
404867www.sauder.com/services Page 9
C
Z
Surface without
TWIST-LOCK®
FASTENERS
GOLD 5/16" FLAT HEAD SCREW
(4 used in this step)
CCC
Finished edge
Roller end
Finished edge
Roller end
D
AA
Surface without
TWIST-LOCK®
FASTENERS
3
2
1
1
2
3
4
4
Remember:
Righty tighty.
Lefty loosey.

Step 5
å Fasten the UPRIGHTS (C and D) to the SHELF (G). Use
four BLACK 1-7/8" FLAT HEAD SCREWS (TT).
404867 www.sauder.com/servicesPage 10
C
Surface without
TWIST-LOCK®
FASTENERS
D
G
Surface with
TWIST-LOCK®
FASTENERS
Finished edge
Finished edge
Finished edge
BLACK 1-7/8" FLAT HEAD SCREW
(4 used in this step)
TT
Unfinished surface
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution