Sauder 420567 User manual

sauder.com
Night Stand
Model 420567
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-19
Français pg 20-22
Español pg 23-25
Lot # 530076 05/24/19
Purchased: __________________
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
Share your journey!
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep.
Prefer the phone? Give us a ring at 1-800-523-3987.
Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays)
WARNING
CHOKING HAZARD - Small Parts
Not for children under 3 years.
Adult assembly required.

Table of Contents Assembly Tools Required
2-3
4
5-19
20-22
23-25
26
27
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
420567 www.sauder.com/servicePage 2
Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C2 TOP (1)
D BOTTOM (1)
D24 RIGHT DRAWER SIDE (1)
D25 LEFT DRAWER SIDE (1)
D109 DRAWER BACK (1)
D716 DRAWER BOTTOM (1)
E BACK (1)
F RIGHT FRONT LEG (1)
G LEFT FRONT LEG (1)
H REAR LEG (2)
I DRAWER FRONT (1)
O BOTTOM MOLDING (1)
P END MOLDING (2)

Part Identification
420567www.sauder.com/service Page 3
A
B
C2
D
E
F
G
H
I
P
O
H
P
D24
D25
D716
D109

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
420567 www.sauder.com/servicePage 4
HIDDEN CAM - 12
1F
GOLD 5/16" FLAT HEAD SCREW - 8
3S
CAM SCREW - 4
8F
CAM DOWEL - 8
2F
SLIDE CAM - 2
10A
BLACK 9/16" FLAT HEAD SCREW - 4
32S
BLACK 1-1/8" MACHINE SCREW - 1
21S
BLACK 2-1/4" FLAT HEAD SCREW - 4
26S
NAIL - 16
1N
35AA UNIVERSAL CABINET RAIL - 2 35AC DRAWER RIGHT - 1 35AD DRAWER LEFT - 1
12E TACK GLIDE - 4
30S BLACK 1-9/16" FLAT HEAD SCREW - 4
KNOB - 1
5K

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/service/tips
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Push eight HIDDEN CAMS (1F) into the ENDS (A and B)
and BOTTOM (D). Then, insert the metal end of a CAM
DOWEL (2F) into each HIDDEN CAM.
å NOTE: Use the exact holes shown.
420567www.sauder.com/service Page 5
A
B
D
Do not tighten the HIDDEN CAMS in this step.
(8 used)
Arrow
1F
2F
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
Arrow
1F
2F

Step 2
å Push four HIDDEN CAMS (1F) into the ENDS (A and B).
A
B
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
Hole
Arrow
420567 www.sauder.com/servicePage 6
Just think. The sooner
you do this, the sooner
you do something else.
1F
Arrow
1F
Arrow

å Turn four CAM SCREWS (8F) into the FRONT LEGS (F and G).
StepStep 3
8F (4 used)
F
G
420567www.sauder.com/service Page 7

StepStep 4
å Fasten the ENDS (A and B) to the FRONT LEGS (F and G).
Tighten four HIDDEN CAMS.
1
2
B
A
These surfaces
should be even.
Surface with HIDDEN CAMS
Surface with HIDDEN CAMS
F
G
These surfaces
should be even.
Angled edge
Angled edge
Edge with CAM DOWELS
Edge with CAM DOWELS
420567 www.sauder.com/servicePage 8

StepStep 5
å Turn four BLACK 9/16" FLAT HEAD SCREWS (32S) into
the ENDS (A and B) until the shoulders of the SCREWS
rest on the surfaces of the ENDS.
å NOTE: Do not overtighten the SCREWS.
å Slide the END MOLDINGS (P) onto the ENDS (A and B).
Line up the grooves in the MOLDINGS over the heads of
the SCREWS in the ENDS.
å NOTE: If the MOLDING comes up o of the SCREWS,
remove it and slide it on again.
These edges
should be even.
BLACK 9/16" FLAT HEAD SCREW
(4 used in this step)
32S
B
A
P
P
Shoulder
Shoulder
Apply pressure with your hands
as you guide the MOLDINGS over
the SCREWS and onto the ENDS.
Apply pressure with your hands
as you guide the MOLDINGS over
the SCREWS and onto the ENDS.
These edges
should be even.
32S
Surface without
HIDDEN CAMS
Surface without
HIDDEN CAMS
420567www.sauder.com/service Page 9

StepStep 6
å Fasten the REAR LEGS (H) to the ENDS (A and B). Use four
BLACK 2-1/4" FLAT HEAD SCREWS (26S).
B
A
These surfaces
should be even.
Surface with HIDDEN CAMS
Surface with HIDDEN CAMS
H
H
These surfaces
should be even.
Angled edge
Angled edge
Edge with CAM DOWELS
Edge with CAM DOWELS
BLACK 2-1/4" FLAT HEAD SCREW
(4 used in this step)
26S
420567 www.sauder.com/servicePage 10