Sauder 423392 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Enlish p 1-23
Français p 24-26
Español p 27-29
Niht Stand
WARNING
CHOKING HAZARD - Small Parts
Not for children under 3 years.
Adult assembly required.

Table of Contents Assembly Tools Required
3
4
5-23
24-26
27-29
30
31
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
Pae 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the ede
to help distinuish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C TOP (1)
D BACK (1)
D12 RIGHT DRAWER SIDE (1)
D13 LEFT DRAWER SIDE (1)
D62 DRAWER BACK (1)
D701 DRAWER BOTTOM (1)
E RIGHT FRONT/LEFT REAR LEG (2)
F LEFT FRONT/RIGHT REAR LEG (2)
G BOTTOM (1)
H LONG SKIRT (2)
J SHORT SKIRT (2)
K DRAWER FRONT MOLDING (1)
L DRAWER FRONT (1)
M END MOLDING (2)
Pae 3
A
B
C
D
E
F
G
H
J
K
L
M
D12
D13
D62
D701
H
J
F
E
M

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
Pae 4
APPLIQUE CARD - 1
35P
35AA UNIVERSAL CABINET RAIL - 2 35AC DRAWER RIGHT - 1 35AD DRAWER LEFT - 1 10A SLIDE CAM - 2
HIDDEN CAM - 34
1F CAM DOWEL - 6 2F
WOOD DOWEL - 6
15F
CAM SCREW - 28
8F
157K KNOB SET - 2
3S GOLD 5/16" FLAT HEAD SCREW - 8 12S BROWN 1" FLAT HEAD SCREW - 2
30S BLACK 1-9/16" FLAT HEAD SCREW - 4 BLACK 9/16" FLAT HEAD SCREW - 4 32S
GOLD 1" MACHINE SCREW - 2
50S

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratchin your unit or the floor.
å Push six HIDDEN CAMS (1F) into the ENDS (A and B)
and BACK (D). Then, insert the metal end of a CAM
DOWEL (2F) into each HIDDEN CAM.
Pae 5
A
B
D
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
Do not tihten the HIDDEN CAMS in this step.
Arrow
1F
2F
(6 used)

Step 2
å Push twenty-eiht HIDDEN CAMS (1F) into the
BOTTOM (G), SKIRTS (H and J), and the remainin
holes of the ENDS (A and B) and BACK (D).
Pae 6
G
H
J
H
J
A
B
D
1F
Arrow
(28 used)
Arrow
1F
1F Arrow
Arrow
1F
Arrow
The arrow in the HIDDEN
CAM must point toward the
hole in the ede of the board.
Hole
Just think. The sooner
you do this, the sooner
you do somethin else.

å NOTE: Position the LEGS (E and F) exactly as shown.
å Turn twenty-eiht CAM SCREWS (8F) into the exact holes
shown in the LEGS (E and F) and SKIRTS (H and J).
å NOTE: One set of LEGS (E and F) receives four CAM SCREWS
each. The other set of LEGS will have six CAM SCREWS each.
Step 3
Pae 7
H
J
H
J
E
F
F
E
8F
(28 used)
8F

Step 4
Pae 8
A
B
M
åTurn four BLACK 9/16" FLAT HEAD SCREWS (32S) into
the ENDS (A and B) until the shoulders of the SCREWS
rest on the surfaces of the ENDS.
åNOTE: Do not overtihten the SCREWS.
åSlide the END MOLDINGS (M) onto the ENDS (A and B).
Line up the rooves in the MOLDINGS over the heads of
the SCREWS in the ENDS.
åNOTE: The MOLDINGS should be centered on the ENDS.
åNOTE: If the MOLDING comes up o of the SCREWS,
remove it and slide it on aain.
BLACK 9/16" FLAT HEAD SCREW
(4 used in this step)
32S
Shoulder
Apply pressure with your hands
as you uide the MOLDINGS over
the SCREWS and onto the ENDS.
Surface without
HIDDEN CAMS
Surface without
HIDDEN CAMS
M

åInsert one WOOD DOWEL (15F) into the RIGHT FRONT/LEFT
REAR LEG (E) with four CAM SCREWS.
åNOTE: Be sure to use the exact hole shown.
åFasten the RIGHT END (A) to the RIGHT FRONT/LEFT REAR
LEG (E). Tihten two HIDDEN CAMS.
åNOTE: Be sure the WOOD DOWEL in the LEG inserts into the
RIGHT END.
åFasten one of the SHORT SKIRTS (J) to the RIGHT FRONT/
LEFT REAR LEG (E). Tihten one HIDDEN CAM.
Step 5
Pae 9
E
Surface
with
HIDDEN
CAMS
1
2
These surfaces
should be even.
Ede with
CAM DOWELS
A
J
15F
The CAM SCREWS
are closer to this ede.

Step 6
åInsert one WOOD DOWEL (15F) into the LEFT FRONT/RIGHT
REAR LEG (F) with six CAM SCREWS.
åNOTE: Be sure to use the exact hole shown.
åFasten the LEFT FRONT/RIGHT REAR LEG (F) to the RIGHT
END (A) and SHORT SKIRT (J). Tihten three HIDDEN CAMS.
åNOTE: Be sure the WOOD DOWEL in the LEG inserts into the
RIGHT END.
Pae 10
A
J
F15F
These surfaces
should be even.