Sauder Barrister Lane 414720 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-22
Français pg 23-25
Español pg 26-28
Lot # 376462 09/14/15
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987
Highboy TV Stand
Barrister Lane Collection | Model 414720
Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
Your holder for all
things awesome.

Table of Contents Assembly Tools Required
3
4
5-22
23-25
26-28
29-30
31
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Use of a TV that is too heavy or large is hazardous. A TV that is too heavy will create a risk of a tip-over that can cause severe injury or
death. A TV that is too large for the available space might be accidentally pushed or bumped o the furniture, or subject to tip-over.
• Check the size and weight of your TV. Compare it to the diagram below – before you begin assembly!
• This Sauder unit is designed for use with televisions weighing less than 50 pounds. Never use with a TV that weighs more.
• The size of the television, front-to-back and side-to-side, must fit within the space defined in the diagram.
• Never place the front edge of the TV past the front edge of the TV support shelf (or stop molding – if equipped)
• Never allow the sides of the TV to extend past the side edges of the TV support surface.
• If the TV has a CRT picture tube, the picture tube cone may extend past the rear of the support shelf.
• Be sure to apply the warning label as instructed in the last assembly step. The label provides important safety related information.
WARNING
!
50 lbs.
50 lbs.
18-3/4"
18-3/4"
41-5/8"
41-5/8"
Skip the power trip.
This time.
414720 www.sauder.com/servicesPage 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C LOWER RIGHT END (1)
D LOWER LEFT END (1)
E UPRIGHT (1)
F LOWER UPRIGHT (1)
G2 TOP (1)
H BOTTOM (1)
I SHELF (1)
J BACK (1)
K BRACE (1)
L DOOR (4)
M FRONT MOLDING (1)
N RIGHT MOLDING (1)
O LEFT MOLDING (1)
P2 FRONT BASE (1)
Q SIDE BASE (2)
R SIDE RAIL (2)
S BACK RAIL (1)
Now you know
our ABCs.
414720www.sauder.com/services Page 3
A
B
C
D
E
F
G2
H
I
J
K
L
L
L
L
M
N
O
P2
Q
Q
R
RS

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
414720 www.sauder.com/servicesPage 4
PULL- 4
70K
DOOR SLIDE - 8
37M
DOOR HANGER- 8
40G
BROWN 7/16" LARGE HEAD SCREW - 16
6S
RUBBER SLEEVE - 8
2R
BLACK 1-7/8" FLAT HEAD SCREW - 15
2S
MOLDING
CONNECTOR - 2
19F
NAIL - 46
1N METAL PIN - 8 1R
SILVER 1-1/8" FLAT HEAD SCREW - 7
10S
CAM SCREW - 4
8F
HIDDEN CAM - 16
1F CAM DOWEL - 12 2F ANGLE BRACKET - 8 5G
BLACK 9/16" LARGE HEAD SCREW - 24
1S
DOOR STOP - 4
4I
GOLD 1" MACHINE SCREW - 8
50S
BROWN 1" FLAT HEAD SCREW - 4
12S
WARNING
Never use this furniture with a TV that is
too large or too heavy. Severe injury or
death can occur.The TV and furniture
will be unstable and may tip.
-The TV must less than 50 lbs.
-The base of the TV must be able to sit
completely on this shelf.
Refer to instruction book for complete
safety information.
Note: This is a permanent label. Do not
try to remove. Surface will be damaged.
08/05 2 6 9 2 2 0 269220
WARNING LABEL - 1
1L
(Refer to the last step for proper
location and application)

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Push sixteen HIDDEN CAMS (1F) into the ENDS (A
and B), LOWER ENDS (C and D), UPRIGHTS (E and F),
and BOTTOM (H). Then, insert the metal end of a
CAM DOWEL (2F) into each HIDDEN CAM, except in
the ENDS (A and B).
414720www.sauder.com/services Page 5
A
B
E
C
D
F
H
Arrow
1F
2F
Do not tighten the HIDDEN CAMS in this step.
Do not insert
CAM DOWELS
into these edges.
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
(16 used)
(12 used)
Arrow
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
Hole
Scan this QR code or go to this address:
http://qr.sauder.com/?ID=1269
to watch a video on how to assemble your unit.

Step 2
å Fasten eight DOOR SLIDES (37M) to the ENDS (A and B),
LOWER ENDS (C and D), and UPRIGHTS (E and F). Use
twelve BROWN 7/16" LARGE HEAD SCREWS (6S).
414720 www.sauder.com/servicesPage 6
A
B
E
C
D
F
Finished edge
Finished edge
Finished edge
Finished edge
The large hole will be
closest to the finished
edge of all parts.
Do not fasten this end of the
DOOR SLIDE until step 17.
Do not fasten this end of the
DOOR SLIDE until step 17.
37M
37M
37M
37M
37M
37M
37M
37M
37M
37M
BROWN 7/16" LARGE HEAD SCREW
(12 used in this step)
6S

å Fasten the RAILS (R and S) to the TOP (G2). Use seven
BLACK 1-7/8" FLAT HEAD SCREWS (2S).
Step 3
414720www.sauder.com/services Page 7
G2
R
R
S
Rounded edge
Rounded edge
Finished surface
Surface with
more holes
BLACK 1-7/8" FLAT HEAD SCREW
(7 used in this step)
2S

Step 4
å Tap two MOLDING CONNECTORS (19F) into the notches
in the MOLDINGS (M, N, and O).
414720 www.sauder.com/servicesPage 8
Flat end
Flat end
MN
O
19F
19F
Use your hammer to tap the MOLDING CONNECTORS (19F) into the notches in the MOLDINGS.

å Fasten the MOLDINGS (M, N, and O) to the TOP (G2).
Use seven SILVER 1-1/8" FLAT HEAD SCREWS (10S).
å NOTE: Do not over tighten the SCREWS into the TOP.
Step 5
414720www.sauder.com/services Page 9
M
N
O
G2
Finished surface
SILVER 1-1/8" FLAT HEAD SCREW
(7 used in this step)
10S

Step 6
å Turn four CAM SCREWS (8F) into the MOLDINGS (N and O).
414720 www.sauder.com/servicesPage 10
8F
N
O