Sauder 421952 User manual

sauder.com
Lift-Top Coee Table
Model 421952
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-23
Français pg 24-26
Español pg 27-29
Lot # 531007 06/25/19
Purchased: __________________
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
Share your journey!
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep.
Prefer the phone? Give us a ring at 1-800-523-3987.
Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays)
Guaranteed to hold
other beverages, too.

Table of Contents Assembly Tools Required
3
4
5-23
24-26
27-29
30
31
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
421952 www.sauder.com/servicePage 2
Short Screwdriver
Adjustable Wrench

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C BACK PANEL (1)
D SHELF (1)
E BOTTOM (1)
F RIGHT FRONT/LEFT REAR LEG (2)
G LEFT FRONT/RIGHT REAR LEG (2)
H LONG SKIRT (2)
I SHORT SKIRT (2)
J STRETCHER (1)
K FRONT PANEL (1)
L TOP (1)
Now you know
our ABCs.
421952www.sauder.com/service Page 3
A
B
C
D
E
F
G
H
I
J
K
L
G
F
I
H

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
421952 www.sauder.com/servicePage 4
23M LIFT TABLE
MECHANISM SET - 1
SUPPORT
BRACKET - 2
37G PULL - 2
149K
HIDDEN
CAM - 24
1F CAM DOWEL - 4 2F 7F TWIST-LOCK®
FASTENER - 4 CAM SCREW - 20
8F
METAL
BRACKET - 12
4G BUMPER - 6
2M WASHER - 10
13M
NUT - 8
24M BUSHING - 2
91M
BLACK 9/16" LARGE HEAD SCREW - 40
1S SILVER 1/2" MACHINE SCREW - 4 38S
BLACK 3/4" PAN HEAD SCREW - 2
85S BLACK 3/4" MACHINE SCREW - 4
92S
BLACK 1-1/4" MACHINE SCREW - 4
93S
APPLIQUE CARD - 4
79P
TACK GLIDE - 4
13E

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/service/tips
å Assemble your unit on a carpeted floor or on the
empty carton to avoid scratching your unit or the floor.
å To begin assembly, push a SAUDER TWIST-LOCK®
FASTENER (7F) into the large holes in the BACK
PANEL (C) and FRONT PANEL (K).
421952www.sauder.com/service Page 5
Do not tighten the TWIST-LOCK® FASTENERS in this step.
7F
7F
C
K

Step 2
å Push four HIDDEN CAMS (1F) into the SHELF (D). Then,
insert the metal end of a CAM DOWEL (2F) into each
HIDDEN CAM.
421952 www.sauder.com/servicePage 6
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
Arrow
1F
2F
(4 used)
Do not tighten the HIDDEN CAMS in this step.
D
Surface with holes
on the short edges

å Push twenty HIDDEN CAMS (1F) into the ENDS (A and B),
BOTTOM (E), and PANELS (C and K).
Step 3
421952www.sauder.com/service Page 7
A
B
C
E
K
Arrow
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
Hole
1F
Arrow
(20 used)
Arrow
1F
Just think. The sooner
you do this, the sooner
you do something else.

Step 4
å Turn twenty CAM SCREWS (8F) into the LEGS (F and G).
421952 www.sauder.com/servicePage 8
F
G
F
G
8F
8F
(20 used)

å Fasten the RIGHT END (A) to the LEGS (F and G). Tighten
four HIDDEN CAMS.
å NOTE: Be sure to position the LEGS exactly as shown.
Step 5
421952www.sauder.com/service Page 9
1
2
A
F
G
These holes must be here. These small holes should
be closer to this edge.

Step 6
å Fasten the LEFT END (B) to the LEGS (F and G). Tighten
four HIDDEN CAMS.
å NOTE: Be sure to position the LEGS exactly as shown.
421952 www.sauder.com/servicePage 10
F
G
B
These holes must be here.
These small holes should
be closer to this edge.

å Fasten the PANELS (C and K) to the SHELF (D). Tighten
four TWIST-LOCK® FASTENERS.
Step 7
421952www.sauder.com/service Page 11
How to use the SAUDER TWIST-LOCK® FASTENER
1. Insert the dowel end of the FASTENER into the
hole of the adjoining part.
NOTE: The dowel end of the FASTENER must
remain fully inserted in the hole of the adjoining
part while locking the FASTENER.
2. Tighten the FASTENER with a Phillips
screwdriver as tight as possible.
Dowel end
Surface with
TWIST-LOCK®
FASTENERS
D
C
Surface without
HIDDEN CAMS
Surface with groove
K

Step 8
å Fasten the SHELF (D) and PANELS (C and K) to the
RIGHT END (A) and LEGS (F and G). Tighten six
HIDDEN CAMS.
421952 www.sauder.com/servicePage 12
Start Tighten
Arrow
Minimum
190 degrees
Caution
Risk of damage or
injury. HIDDEN CAMS
must be completely
tightened. HIDDEN
CAMS that are not
completely tightened
may loosen, and parts
may separate. To
completely tighten:
Arrow
Maximum
210 degrees
F
GA
D
C
K
These holes are closer to this leg.
This PANEL has a groove.
Surface with
HIDDEN CAMS

å Fasten the BOTTOM (E) to the LEGS (F and G). Tighten
two HIDDEN CAMS.
Step 9
421952www.sauder.com/service Page 13
F
G
E
Surface with
HIDDEN CAMS

Step 10
å Fasten the LEFT END (B) and LEGS (F and G) to the
SHELF (D), BOTTOM (E), and PANELS (C and K). Tighten
eight HIDDEN CAMS.
å NOTE: Use the Short Screwdriver to tighten the HIDDEN
CAMS in the SHELF.
421952 www.sauder.com/servicePage 14
D
C
K
F
G
B
E
Now might be a
good time to refresh
your drink.

å Fasten twelve METAL BRACKETS (4G) to the BOTTOM (E).
Use twelve BLACK 9/16" LARGE HEAD SCREWS (1S).
å NOTE: Be sure four of the BRACKETS are even with the
SHORT edges of the BOTTOM.
å Fasten the SKIRTS (H and I) to the BOTTOM (E). Use twelve
BLACK 9/16" LARGE HEAD SCREWS (1S) through the
BRACKETS and into the SKIRTS.
å NOTE: There are no pre-drilled holes in the SKIRTS. The
SCREWS will tighten into the grooves.
Step 11
421952www.sauder.com/service Page 15
BLACK 9/16" LARGE HEAD SCREW
(24 used in this step)
1S
4G
4G
4G
4G
E
I
H
H
I
The groove
is closer to
this edge.
The groove
is closer to
this edge.
(12 used)

Step 12
å Using your hammer, gently tap four TACK GLIDES (13E)
into the bottoms of the LEGS (F and G).
421952 www.sauder.com/servicePage 16
F
G
F
G
13E

å Carefully stand your unit upright.
å Push six BUMPERS (2M) into the PANELS (C and K)
and LEGS (F and G).
å Fasten the PULLS (149K) to the FRONT PANEL (K). Use
four SILVER 1/2" MACHINE SCREWS (38S).
Step 13
421952www.sauder.com/service Page 17
F
G
F
G
C
K
2M
149K
SILVER 1/2" MACHINE SCREW
(4 used for the PULLS)
38S

Step 14
å Fasten the LIFT TABLE MECHANISMS (23M) to the TOP (L).
Use six BLACK 9/16" LARGE HEAD SCREWS (1S).
å NOTE: Be sure to position the LIFT TABLE MECHANISMS on
the TOP exactly as shown.
421952 www.sauder.com/servicePage 18
L
Surface with holes
23M
23M
BLACK 9/16" LARGE HEAD SCREW
(6 used in this step)
1S
This hole
must be here.
Meet Part (L). This component has
been engineered to be lighter, stronger,
faster… well ok. Not technically faster. But
definitely makes for a sturdier Lift-Top
Coee Table that’s easier to assemble
and friendlier to the environment.

å Fasten the SUPPORT BRACKETS (37G) to the LIFT
TABLE MECHANISMS (23M). Use four WASHERS (13M),
NUTS (24M), and BLACK 3/4" MACHINE SCREWS (92S).
å NOTE: Use the adjustable wrench in this step.
Step 15
421952www.sauder.com/service Page 19
37G
37G
23M
23M
BLACK 3/4" MACHINE SCREW
(4 used in this step)
92S
13M
24M
13M
24M
92S
92S

Step 16
421952 www.sauder.com/servicePage 20
å IMPORTANT: You will need someone's help in this step.
å Fasten the TOP (L) to the ENDS (A and B). Use ten BLACK 9/16" LARGE HEAD SCREWS (1S) through the LIFT TABLE
MECHANISMS (23M) and into the holes in the ENDS.
å NOTE: Be careful when lining up the holes in the MECHANISMS with the holes in the ENDS as to not damage any parts.
You should start each SCREW a few turns before completely tightening any of them.
23M
23M
B
A
BLACK 9/16" LARGE HEAD SCREW
(10 used in this step)
1S
These four holes
must be here.
L
This hole will be used
in the next step.
This hole will be used
in the next step.