Sauder 423399 User manual

Lot # 530610 06/24/19
Purchased: __________________
English pg 1-14
Français pg 15-17
Español pg 18-20
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Share your journey!
5-Shelf Bookcase
Model 423399
Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep.
Prefer the phone? Give us a ring at 1-800-445-1527.
Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays)
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
The stories of your life.

Table of Contents Assembly Tools Required
2
3
4-14
15-17
18-20
21-22
23
Hardware Identification
Part Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Page 2 www.sauder.com 423399
Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
HIDDEN CAM - 46
1
CAM COVER - 18
54 TACK GLIDE - 4
SILVER 1-1/2" FLAT HEAD SCREW - 4
11
NAIL - 46
10
CAM SCREW - 46
2METAL PIN - 12 3
FURNITURE TIPPING RESTRAINT KIT - 1
99
Skip the power trip.
This time.

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A UPPER RIGHT END (1)
B UPPER LEFT END (1)
C LOWER RIGHT END (1)
D LOWER LEFT END (1)
E TOP (1)
F BOTTOM (1)
G SHELF (1)
H ADJUSTABLE SHELF (3)
J ADJUSTABLE SHELF MOLDING (3)
K VALANCE (1)
L SHELF MOLDING (1)
M BASE (1)
N UPPER END MOLDING (2)
O LOWER END MOLDING (2)
P LARGE BACK (1)
Q SMALL BACK (1)
Now you know
our ABCs.
Page 3www.sauder.com423399
E
F
B
A
D
C
G
H
K
L
M
N
O
P
Q
J
HJ
HJ
N
O

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on
the empty carton to avoid scratching your unit
or the floor.
å Push forty-six HIDDEN CAMS (1) into the
ENDS (A, B, C, and D), TOP (E), BOTTOM (F),
SHELF (G), and ADJUSTABLE SHELVES (H).
Arrow
1
1
Arrow
1
Arrow
Arrow
1
Arrow
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
Hole
(46 used)
Page 4 www.sauder.com 423399
E
F
B
A
D
C
G
H
H
H
Some assembly
(and snacks) required.

StepStep 2
å Turn forty-six CAM SCREWS (2) into the ENDS (A, B, C,
and D), SHELF (G), SHELF MOLDINGS (J and L),
VALANCE (K), BASE (M), and END MOLDINGS (N and O).
Page 5www.sauder.com423399
2
K
L
M
N
O
J
J
J
N
O
B
A
D
C
G

Step
å Fasten the UPPER ENDS (A and B) to the TOP (E). Tighten
four HIDDEN CAMS.
Step 3
Page 6 www.sauder.com 423399
1
2
E
B
A
Surface with HIDDEN CAMS
Surface with HIDDEN CAMS
Surface without HIDDEN CAMS
Edge with HIDDEN CAMS
Edge with HIDDEN CAMS
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution

StepStep 4
å Fasten the SHELF (G) to the UPPER ENDS (A and B). Use
four SILVER 1-1/2" FLAT HEAD SCREWS (11).
Page 7www.sauder.com423399
SILVER 1-1/2" FLAT HEAD SCREW
(4 used in this step)
11
B
A
G
Edge with HIDDEN CAMS
Surface with HIDDEN CAMS

Step
å First, fasten the LOWER ENDS (C and D) to the
BOTTOM (F). Tighten four HIDDEN CAMS.
å Then, fasten the LOWER ENDS (C and D) to the
SHELF (G). Tighten four HIDDEN CAMS.
Step 5
Page 8 www.sauder.com 423399
F
D
C
D
C
G
Surface with
HIDDEN CAMS
Surface with HIDDEN CAMS
Surface without HIDDEN CAMS
Edge with
HIDDEN CAMS
Edge with
HIDDEN CAMS
Just think. The sooner
you do this, the sooner
you do something else.
1st
2nd

StepStep 6
Page 9www.sauder.com423399
å Unfold the SMALL BACK (Q) and lay it over the bottom of
your unit.
å Make equal margins along all four edges of the SMALL
BACK (Q). Push on opposite corners of your unit if needed to
make it "square".
å Fasten the bottom and side edges of the SMALL BACK (Q) to
your unit using the NAILS (10).
å NOTE: Do not fasten the upper edge of the SMALL BACK at
this time.
å Repeat this step for the LARGE BACK (P).
å NOTE: The LARGE BACK (P) will overlap the SMALL BACK (Q).
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution
Unfinished
surface
P
Q
Unfinished
surface
Do not fasten NAILS along this
edge until the LARGE BACK (P) is
overlapping the SMALL BACK (Q).
P
Q
G
The LARGE BACK (P) will
overlap the SMALL BACK (Q)
along the SHELF (G).
NAIL
(46 used in this step)
10

StepStep 7
Page 10 www.sauder.com 423399
å Carefully turn your unit over onto its back.
å Fasten the VALANCE (K) to the TOP (E) and UPPER
ENDS (A and B). Tighten five HIDDEN CAMS.
å Fasten the UPPER END MOLDINGS (N) to the UPPER
ENDS (A and B). Tighten six HIDDEN CAMS.
E
B
A
K
N
N
These surfaces
should be even.